629832
12
Zoom out
Zoom in
Previous page
1/24
Next page
12
nuswelle oder das 320V-Netz
- Nutzen Sie einen Wechselrichter mit einer Unterspannungssicherung, um die Batterie zu
schonen.
- Schließen Sie alles wie auf Bild 1-2 an.
EINSTELLUNG
Wenn Sie möchten, kann Folgendes noch eingestellt werden.
- Regeln der Neigung beim Ausdrehen. Fig. 7 und 8.
- Die Gegenmutter lösen (Schlüssel SW13).
- Drehen Sie die Imbusschraube rechts, dann hebt sich der Gelenkarm höher und links,
dann senkt der Arm tiefer (Imbusschlüssel 4mm). Bitte stützen Sie den Arm beim
abregeln.
- Die Gegenmutter wieder anziehen. Halten Sie die Imbusschraube beim Andrehen der
Mutter fest.
MÔGLICHE STÔRUNGEN
Siehe Beschreibung in der Gebrauchsanweisung 6AC903.
TECHNISCHE ANGABEN DES MOTORS
- Versorgungsspannung: 230V AC, 50Hz
- Leistung Motor: max. 260 W.
- Der Motor entspricht den EG Richtlinien 73/23/EEG und 89/336/EEG.
- Die Funkinstallation entspricht den EG Richtlinien 1999/5/EC.
BEMERKUNG
Der Sender und der Motor sind auf einander abgestimmt. Bei Bestellung eines neuen
Senders, muss der Sender mit den Motor neu synchronisiert werden. Siehe hierfür die
Instruktionen beim Motor Nice Neomat HT, Tabelle A13, A1 und A3.
GB
ELECTRIC CONNECTION
You always have to connect to the 230V supply. If there is no 230V supply available,
then you should use an inverter to convert the voltage. Connection of the inverter, see
further on.
- Connect the wires as shown on the diagram fig. 1-2.
-
- Place a 6A fuse in the conductor. In order to avoid short circuiting wait before introduc-
ing the fuse until the electrical connection is completed.
- It’s important to install the relay as shown as in the diagram, in order to disconnect the
current to the motor whilst driving. Install the relay so that it is out of reach for anyone
else.
- Ensure that the wiring is connected and cannot come loose.
- Introduce the fuse into the fuse holder. Two long beeps will be heard immediately.
- Use the remote to program the end switches.
CONNECTION INVERTER
You can use an inverter to convert the power supply (12V DC or 24 V DC) into the suit-
able power supply for the motor (230V AC).
- Use an inverter which meets this specifications:
intput: 10 – 15 V DC (or 20 - 30 V DC)
output: 230V AC / 50Hz
capacity: 300W permanent, 600W max
- To program your motor : us an inverter with sine wave output or the 230V supply
- Use an inverter with lower voltage security, if not then there is a possibility that the un-
charged inverter will drain your battery.
- Make the connection as on fig 1-2
EXTRA ADJUSTMENT
If required the following adjustments can be made.
- Adjustment of the angle of projection. Fig 7 and 8. This can be useful for awnings in a
high postion or when the awning touches the door.
- Loosen the counter nut (wrench SW13).
- Turn the hexagonal socket screw to the right for a higher and to the left for a lower pro-
jection of the arm ( socket head wrench 4mm). hold the arm while adjusting.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thule Omnistor 9200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thule Omnistor 9200 in the language / languages: All languages as an attachment in your email.

The manual is 6,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info