658771
22
Zoom out
Zoom in
Previous page
1/32
Next page
P18
CONTROL PANEL
the identified source. In order to update from a USB disk, you need to download the updated software file
from our website to the root directory on the USB disk first.
The USB disk should be plugged in the USB port before executing the System Update option. Do not
remove the USB disk until the complete software update process is completed. In order to update over
the Internet, the receiver must be connected to the Internet over a LAN or WLAN connection. Remove any
USB device from the USB port before you execute the System Update option. If the System Update option
is executed but there is no USB disk connected and no Internet connection, the receiver will search for a
newer software version over the satellite. This procedure may take very long time depending on the size
of the new software file and therefore it is recommended to use the USB or Internet methods described
above for software updates. After the new software file was downloaded, the receiver will store the new
software and automatically restart. All user preferences and channel lists will remain unchanged.
ATTENTION: Be careful not to interrupt the software update process by removing the USB stick,
disconnecting the Internet or turning off the receiver, or otherwise interrupting the installation
process. If the installation is interrupted by accident, such as by a power failure, the receiver
may not boot up properly afterwards.
9.11 System Information
This menu displays information related to the software and hardware version of the receiver. This
information may be required if you request service or repair.
9.12 Audio/Video Settings
This is where you can set the basic audio and video parameters of your receiver related to connections on
the rear panel.
9.12.1 Digital Audio Out
Use this option to specify desired audio format on the digital audio outputs (SPDIF / HDMI). Please check
that your TV supports Dolby Digital and DTS over HDMI.
9.12.2 HDMI Video output
Use this option to specify the video output format on the HDMI connector.
Dolby DRC Use this option to set the Dynamic Range Control when using Dolby technology.
Line is more suitable for effects reproduction, while RF produced a higher voice level.
Audio track Use this option to select a preferred audio track language.
9.12.3 HDCP
Use this option to set HDCP protocol over the HDMI connection On or Off.
9.12.4 Analogue video output
Use this option to enable/disable the analogue video outputs.
9.12.5 Adaptive scan HDMI
Use this option to adjust the screen frequency over the HDMI connection to allow for optimal picture
quality during video playback.
9.13 Antenna Settings
Antenna setting options were described under the Installation Wizard chapter.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson THS 845 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson THS 845 in the language / languages: English as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info