658771

Thomson THS 845 Manual

12
Zoom out
Zoom in
Previous page
1/32
Next page
P8
STARTING UP FOR THE FIRST TIME
the remote control to navigate forward or back through the wizard steps. Press the OK button to edit a
parameter and select its value from the drop list that will appear on the right side of the screen.
4.1 Menu Language and Tuner type
This is where you can set the menu language and select the tuner type. First select the language to be
used for all menus by pressing the tu buttons.
Select Streaming source if you want to use an external satellite tuner as SAT-IP server. The most common
way is to confirm the setting Local tuner.
Press the GREEN button on the remote control to proceed to Antenna settings.
4.2 Antenna Settings
Satellites 1 – 4: To set up the receiver for the type of connected antenna, follow the instructions
below. Select the satellites you wish to receive with the receiver. Each of the
satellites in the built-in satellite list is configured with predefined default
parameters. You may press the BLUE button to edit these values. See below
details for advanced settings. In case you use Astra 19.2 satellites, skip these steps
and press the GREEN button (continue reading chapter 4.4 Channel Search).
4.3 Advanced Satellite Settings
LNB Type: Select Universal for most standard LNBs or Unicable if you have a Unicable SatCR
LNB or multiswitch.
Satellite: Use this option to select the satellite for which you would like to set the position.
Use the COLOUR BUTTONS on the remote control, as shown at the bottom of
the screen, to delete or add a satellite from the satellite list and set their individual
settings.
LOF Low and High Band: The LOF (Local Oscillator Frequency) of the LNB is usually printed on the LNB itself
or in its documentation. You can set the High and Low LOF frequencies to match
the LNB here.
Band switching: The receiver uses a 22 kHz signal to control the band of the LNB. If you do not
know if your LNB supports this feature, set the option to Auto.
DiSEqC type and DiSEqC input:
You can connect up to two cascadable DiSEqC switches to the receiver. This
option allows you to set the type and input port for each switch.
Reference transponder: This option allows you to set which transponder is used as the reference for the
satellite signal strength.
Transponder number: Use this option to select a transponder from the built-in transponder list. Once
selected from the list, the Frequency, Polarity and Symbol rate fields will be updated
accordingly. Alternatively you can set these fields manually.
Frequency: Set the frequency of the reference transponder.
Polarity: Set the polarity of the reference transponder.
Symbol rate: Set the symbol rate of the reference transponder.
Tuner IF and Channel ID (SatCR only):
This option allows you to select the SatCR Tuner IF frequency (also known as User
Band frequency) and the channel ID for the receiver. In a typical SatCR installation,
you are able to connect multiple receivers to a single LNB or Multiswitch output,
with each receiver set to connect to a different SatCR user band and channel ID.
Signal strength and signal quality bars:
In two level bar meters, on the right side of the screen, the user can see the
strength and quality of the signal coming from the antenna dish to the tuners.
These two meters can be used while doing a fine-tuning of the antenna position.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson THS 845 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson THS 845 in the language / languages: English as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info