658771
8
Zoom out
Zoom in
Previous page
1/32
Next page
P4
YOUR RECEIVER
2.0 YOUR RECEIVER
2.1 DEFAULT PIN-CODE: 0000
2.2 Front Panel
Fig.1
1. Standby/ON button Turns the receiver ON or into Standby
2. Navigations buttons Menu navigation
3. LED Display Displays channel number, time, videotext page or recording modes
4. Indicator LED GREEN indicates that the receiver is currently ON
5. IR Sensor Receives the RCU commands
2.3 Side Panel
Fig.2
1. Smart card slot To insert your HD+ smart card with the golden chip to bottom side.
2.4 Rear Panel
Fig. 3
1. SAT OUT To loop through the satellite signal to a second receiver
2. SAT IN To connect to the LNB of your satellite antenna for reception of satellite
broadcast signal
3. USB To connect your USB storage device
4. HDMI To connect to the HDMI input of your TV set using a good quality HDMI
cable
5. OPTICAL S/PDIF To connect to a digital amplifier or home theatre using an optical cable
6. VIDEO To connect to the TV or DVD/VCR recorder for analogue video signals. (This
connection supports Standard Definition TV resolutions only.)
7. COAXIAL S/PDIF To connect to a digital amplifier or home theatre using a coaxial cable
8. AUDIO L/R To connect to the TV or DVD/VCR recorder for analogue stereo audio
9. ETHERNET To connect to a Local Area Network (LAN) at home.
10. DC POWER To connect to the original included main power adapter (Input ~230 V
50~60 Hz/ Output 12 V, 2 A DC
)
11. Power switch To power switch ON or OFF your receiver
2.5 Remote Control
2.5.1 Batteries
Fig. 4
First time Use
Two 3 V Lithium CR2032 batteries come pre-installed in your remote control. When using the remote for
the first time, pull out the plastic tab from the remote to activate the batteries.
Replacing the Batteries
With screwdriver, remove the battery tray. Insert the batteries with the “+” marking facing up into the
battery tray. Slide the tray back into the remote until it clicks.
ATTENTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson THS 845 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson THS 845 in the language / languages: English as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info