Manual Thomson ROC6507 (page 9 of 48) (English, German, Dutch, French, Italian, Spanish)

607822

Zoom out

Zoom in

1/48

Notes on learning: Do not try to perform learning

directly under fluorescent lights or in weak lighting

conditions since this could cause interference with the IR

transmissions. Place the remote control at least 1 metre

[3 feet] from any light source • Avoid copying the volume

and mute keys on your original remote control, unless

you are sure that they activate the same target device;

for example, certain original DVD remote controls may

also include a TV volume/mute key: they may have two

different types of codes • Avoid learning VCR keys on your

original remote control unless you are sure that they

activate the same target device; for example, certain

original TV remote controls may also include a VCR key:

they may have two different types of codes • Copying

a key may take up to 3 seconds. Do not release the key

being copied unless the “

Success” or “Key Learn Error”

screens are displayed.

If copying the rst or second keys for a certain mode

constantly cause errors, use the following procedure:

i. End the learning session by pressing the

EXIT key.

ii. Clear the commands learned for this mode.

iii. Verify that the IR LED’s are properly aligned between the

two remote controls.

iv. Ajust the gap between the two remote controls so as to

reduce or increase the distance (from 15 mm to 50 mm

[1/2 to 2»]).

v. Tr y learning the original remote control again for this

mode.

If the problem continues for the same key, verify that the key

on the original remote control was properly learned; does

it send the signals? Does it activate the target device? Try

copying this key using a dierent mode. If the learning is

correct, the type of code may be dierent from the others

and cannot be copied in the same mode.

Macro commands

This function permits storing sequences of commands

using the MACRO key. You can program and store up

to 3 sequences of successive keystrokes for several

keys of your choice. By pressing the respective Macro

digital key, this sequence of successive keystrokes

(IR commands) is sent. Any sequence of successive

keystrokes performed frequently may be reduced to

only two commands (MACRO key plus one of the 1, 2 or

3 keys). For example, by pressing MACRO and then only

one key, you can turn on your TV set, display your favorite

channel, turn on your VCR and start a recording, etc.

You can store a sequence of 10 commands for each 1, 2

or 3 key.

How to set up a macro

Tip: Set up your macro on a sheet of paper by

writing down the series of 10 keystrokes (maximum)

that it is composed of. As an example, if you want to

turn on your TV set to Channel 3 and then turn on a

satellite receiver to Channel 5, you should write down:

MACRO, 1 (for storage for this key), TV (�), 3, SAT (�),

5, MACRO.

1. Using the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display CODE

SETUP then navigate up to MACRO SETUP (press

OK) then MACRO KEY SET (press OK) then SELECT A

MACRO KEY.

2. Press once on the 1, 2 or 3 key to which you wish to

assign the macro.

The indication SELECT MACRO X MODE? appears.

4. Press once on the desired mode key (TV, DVD,

VCR, etc.) to select the device that will receive the

command SELECT MACRO X KEY? is displayed.

Note: The rst key in the Macro sequence must always be

a mode key.

5. Press each of the keys in order that make up the

macro.

6. Store the macro by pressing the MACRO key once.

7. The display briey indicates PLEASE WAIT before

leaving this mode.

Note: the Macro is automatically stored the 10th time the

key is pressed.

8. The display briey indicates SUCCESS before leaving

this mode.

How to clear a macro

1. Using the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display CODE

SETUP then navigate up to MACRO SETUP (press OK)

then MACRO KEY CLEAR (press OK) then SELECT A

MACRO KEY.

2. Press once on key 1, 2 or 3 of the macro to be cleared

to display CONFIRM OK TO CLEAR

3. Press OK once.

4. The display briey indicates SUCCESS before leaving

this mode.

How to use a macro

In normal operation, to activate the Macro, press and

release the MACRO key, then (within 20 seconds) press

and release key 1, 2 or 3 to display MACRO X while the

Macro sequence is being run and remote control returns

to normal function. While the Macro is being executed,

the remote control must be pointed at the devices to be

controlled.

Note: if there is no Macro stored for the number key selected,

“Macro X Void“ is displayed.

Notes on macros: The time elapsed between each automatic

command during the execution of a macro is 1/2 second.

For certain commands, you may have to add pauses in a

macro sequence (for example, to allow the TV set to warm

up). These pauses may be adjusted by using the PAUSE key,

followed by a number of seconds from 1 to 9. The rst key

stored in a Macro sequence must be a Mode key (TV, VCR,

etc.). The SETUP, HOME CINEMA and MACRO keys may

not be included in a Macro. Press SETUP in order to exit

Macro Setup.

Home Cinema Function

The Home Cinema function uses up to 5 devices with

one mode key: the HOME CINEMA key. The 5 devices

correspond to the ve mode keys (TV, DVD, AMP. ..) that

will be associated with predened keys. The keys are:

a. The 2 program keys PROG + / -.

b. The 3 volume VOL + / - keys and the mute ( ) key.

c. The 6 run keys Play, Pause, Stop, Fast Forward, Fast

Rewind and Record 7,4,8,=,<,;.

d. Directional keys: up, down, right and left 5,6,4,3

and the MENU, EXIT, OK keys.

e. For the remaining keys: "base" mode HOME CINEMA

(any one of the other modes).

Example: In Home Cinema mode, you can set up the

PROG+/ keys to control the satellite receiver, the VOL +/

and ( ) keys to control the amplier, the Run keys (PLAY,

PAUSE, etc.) to control the DVD player, the MENU, EXIT, etc.

keys to control the DVD player, and the other keys to control

the TV set.

How to program the Home Cinema function

1. Using the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display CODE

SETUP then navigate to HOME CINEMA SETUP (press

OK) then HOME CINEMA SET (press OK) then PROG/

CHAN KEY GROUP MODE?.

2. Choose a mode key (TV, DVD, VCR, etc.) for the PROG

+ / - keys.

> VOLUME & MUTE KEYS MODE? appears.

3. Choose a mode key (TV, SAT, AMP, AUDIO, etc.) for

the VOL + / - keys.

>RUN KEYS MODE? appears.

4. Choose a mode key (TV, DVD, VCR, etc.) for the

7,4,8,=,<,;run keys.

>xxx MENU, OK, EXIT MODE? appears

5. Choose a mode key (TV, DVD, VCR, etc.) for the

navigation keys MENU, EXIT, OK.

> ALL OTHER KEYS MODE? appears.

6. Choose a mode key (TV, DVD, VCR, etc.) for the other

remote control keys to be used for Home Cinema

mode.

The display briey indicates PLEASE WAIT then

SUCCESS before returning to CODE SETUP.

How to delete the Home Cinema function

1. Using the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display CODE

SETUP then navigate to HOME CINEMA SETUP (press

OK) then HOME CINEMA RESET.

2. Press OK once to display CONFIRM OK TO RESET.

3. Press OK once.

01_GB_ROC6507.indd 6 15/05/07 9:22:47

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC6507 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thomson ROC6507 Manual

Product: