607822

Thomson ROC6507 Manual

6
Zoom out
Zoom in
Previous page
1/48
Next page
GB
3
Programming the remote control
Setting up the codes
Method A - Programming by scrolling
Used to enter the codes using the list of codes shown
on the display.
1. Turn on the equipment that you wish to control.
2. Hold down the SETUP key until CODE SETUP appears
on the display (for 7 seconds).
3. Press OK once to display SCROLL A LIST OF
CODES.
4. Press OK once to display SELECT A MODE KEY.
5. Press once on the key of the device to be
controlled (TV, DVD, VCR, etc.) to display SELECT
DEVICE TV?
6. Using the navigation keys (5,6), select the device
(DVD, VCR, etc.) then conrm using OK. (for the TV
mode key, only TV may be selected). The rst brand
name and the rst code are displayed (e.g.: ADMIRAL,
0000).
7. Select the brand using the navigation keys 56,
or by selecting the 1st letter of the brand of your
device using keys 2 - 9 (as on a mobile phone: 2=abc,
3=def, etc.) (e.g.: THOMSON : 8 4).
8. Point the remote control at the device and try out
various keys, for example VOL +/-, PROG +/-, etc.
9. If the device responds, store the code using OK.
10. If the device does not respond, change the code using
the 43 keys and try controlling the device again.
11. If you have tried all of the codes for your brand
and the device still does not respond, try Method C
(programming by code search).
Method B - Programming by entering the code
Codes from the separate list (code tables).
1. Turn on the equipment that you wish to control.
2. Hold down the SETUP key until CODE SETUP appears
on the display (for 7 seconds).
3. Press OK once to display SCROLL A LIST OF CODES.
4. Using the navigation keys (5,6), display ENTER
THE CODES then conrm using OK in order to display
SELECT A MODE KEY.
5. Press once on the key of the device to be controlled
(TV, DVD, VCR, etc.). The key selected and the code
stored in memory for this key are shown on the
display (e.g.: TV.....0166).
6. Enter one of the 4-digit codes oered on the list
received separately.
7. The display briey indicates SUCCESS before exiting
the programming mode.
Method C - Programming by code search
Used to manually search for a code in any code library
for a family of devices whose code or commercial brand
may not be included in the separate list or is led in
another fashion.
1. Turn on the equipment that you wish to control.
2. Hold down the SETUP key until CODE SETUP appears
on the display (for 7 seconds).
3. Press OK once to display SCROLL A LIST OF CODES.
4. Using the navigation keys (5,6), display SEARCH
FOR THE CODES then conrm using OK in order to
display SELECT A MODE KEY.
5. Press once on the key of the device to be
controlled (TV, DVD, VCR, etc.) to display SELECT
DEVICE TV?
6. Conrm using OK to display TO SEARCH PRESS …P+
or � (for the TV mode key, only TV can be selected).
7. Point the remote control at the device to be
controlled and try to turn it o using the � key.
8. If the device to be controlled goes o, press OK to
store the code.
9. If the device does not go o, press the � again
several times until the device goes o. Between
two presses on the key, leave time for the device to
respond (1-2 seconds).
10. As soon as the device to be controlled goes o, press
OK to store the code.
11. The display briey indicates SUCCESS before exiting
the programming mode.
Note 1: Each time the (�) key is pressed, the remote control
sends a signal to the device. This signal corresponds to
a code in the code library stored in the remote control
memory. If you go past the required code, use the PROG -
key to go back (or advance using PROG +) inside the code
library.
Note 2: the indication SEARCHING FOR: remains on display
during this mode.
Method D
Programming by search for Brand names
Used to manually search for a brand name (Thomson,
Philips, Sony, etc.) in the code library, which generally
contains 30 to 40 codes.
1. Turn on the equipment that you wish to control.
2. Hold down the SETUP key until CODE SETUP appears
on the display (for 7 seconds).
3. Press OK once to display SCROLL A LIST OF CODES.
4. Using the navigation keys (5,6), display USE
BRAND CODES then conrm using OK in order to
display SELECT A MODE KEY.
5. Press once on the key of the device to be
controlled (TV, DVD, VCR, etc.) to display SELECT
DEVICE TV?
6. Conrm using OK in order to display ENTER THE
BRAND KEY 1-8 (for the TV mode key, only TV can be
selected).
7. Refer to the separate list of codes by brand (this list
comes separately) and key in the number (1 to 8)
that corresponds to the brand of the device to be
controlled. TO SEARCH PRESS P+ OR � is displayed
on the screen.
8. Point the remote control at the device to be
controlled and try to turn it o by pressing the � key
once.
9. If the device to be controlled goes o, press OK to
store the code.
10. If the device does not go o, press the � again several
times until the device goes o. Between two presses
on the key, leave time for the device to respond (1-2
seconds).
11. As soon as the device to be controlled turns o, press
OK to store the code.
12. The display briey indicates SUCCESS before exiting
the programming mode.
Note 1: Each time the (�) key is pressed, the remote control
sends a signal to the device. This signal corresponds to
a code in the code library stored in the remote control
memory. If you go past the required code, use the PROG -
key to go back (or advance using PROG +) inside the code
library.
Note 2: The indication SEARCHING FOR remains on display
during this mode.
Testing the remote control
before programming
1. Turn on the device that you wish to control.
2. Press the key that corresponds to the type of device
to be controlled:
TV: TV set,
DVD: DVD player/recorder,
VCR: video cassette recorder,
STB: satellite, cable, ADSL,
AMP: amplier
AUDIO: Hi-Fi system,
3. Point the remote control at the device to be
controlled and try to turn it o using the � key. If
the device does not go o, you should program the
remote control following one of the procedures A, B,
C or D described below.
Identifying a code: Press and hold a mode key. The
code stored in memory for this mode is displayed (e.g.,
DVD…..0768).
Note: Except for the TV key, every mode key (DVD, VCR,
etc.) can be programmed to control a device other than
the one indicated on the key. It is thus possible to assign,
for example, the DVD mode to the VCR key. You should
enter the code that corresponds to the desired brand and
device following one of the procedures indicated in this
manual.
01_GB_ROC6507.indd 3 15/05/07 9:22:45
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson ROC6507 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC6507 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info