Manual Thomson ROC6411 6in1 Universal Remote Control (page 3 of 36) (All languages)

542010

Zoom out

Zoom in

1/36

2 3

Method C – Programming by means

of code retrieval

Should none of the codes work, you still have the

possibility of retrieving the appropriate code without

having to perform any input.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the indicator lamp

blinks and then remains lit.

3. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player, VCR: Video

recorder, SAT/STB: satellite receiver, cable, DVBT,

ADSL, AMP/AUX: AUDIO equipment and any

other appliance.

4. Direct the remote control towards the set and try to

switch it off by pressing the key G.

5. If the set you want to control switches off, press

OK to memorise the code.

6. Should the set not switch off, press key G as many

times as required (up to 200 times), until the

set switches off. Between two key presses, leave

enough time for the key corresponding to the

indicator lamp to light up again (about 1 second).

Proceeding this way will enable you to see whether

the set responds or not.

7. Immediately upon the switching-off of the set to be

controlled, press OK to store the code.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 3.

Try out other remote control keys to ﬁ nd out the range

of functions you can control. If you think that not all

of the keys are active, repeat the procedure of this

programming method to ﬁ nd out the code supporting a

wider range of features.

Method D – Automatic

code search

With this method, the remote control scrolls through

the full code list by sending an IR signal to the set to be

controlled remotely. Proceed as follows:

1. Check that your equipment is on. If not, switch it on

manually.

2. Hold down the SETUP key until the indicator lamp

blinks and then remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp ﬂ ashes to signal that this time is almost up,

and then goes off).

3. Release the SETUP key.

4. Press the key corresponding to the type of

equipment (for example TV).

5. Press the Prog+ or standby G or B (DVD/

VCR only) key. After a few seconds, the remote

control begins to scroll through the whole code

list included in the library (at a rate of roughly

1 code per second). Press the Prog+ key once

again to slow down the test speed (1 code every

3 seconds). As soon as the set changes channels,

you must press OK to save the code and stop the

remote control scrolling through the list. If you do

not react quickly enough, you can go back to the

previous code by pressing Prog- or E (DVD/

VCR only) as many times as necessary (you can

go forward by pressing G , Prog+ or B (DVD/

VCR only) if you have gone back too far). As soon

as the set responds again, press OK to save the

code.

Method E – Programming for control of a

COMBO (combined TV-VCR, TV/DVD, VCR/

DVD, … set)

Depending on the COMBO group (TV/VCR, VCR/

DVD, etc.) and the make, you will be required to enter

a single code for both devices in the COMBO, or to

enter two codes, one code per device. Consult the

separate list to discover this.

Before you start programming, you must ﬁ nd the

subcode or code of the subset to be controlled

(television or video recorder, ...). Refer to the list

supplied with this user manual (see page subcodes

or codes).

1. Switch on the COMBO you want to control.

2. Hold the SETUP key down until the indicator lamp

blinks and then remains lit.

3. Press the key of the ﬁ rst device to control, and then

follow one of the programming methods A, B, C or

D previously described.

4. If a second code programming is required, then

repeat steps 2 and 3 above.

How to retrieve

a programmed code

It may be useful to retrieve the code programmed in

the remote control.

1. Hold down the SETUP key until the indicator lamp

blinks and then remains lit.

2. Press the key that corresponds to the type of

equipment you want to ﬁ nd the code:

TV: television set, DVD: DVD player, VCR: Video

recorder, SAT/STB: satellite receiver, cable, DVBT,

ADSL, AMP/AUX: AUDIO equipment and any

other appliance.

3. Press the SETUP key brieﬂ y, so that the indicator

lamp blinks once.

4. Press the numbered keys in ascending order (0 to

9) until the indicator lamp blinks once.

5. The number that caused the indicator lamp to blink

is the ﬁ rst of the four numbers that make up your

code. Make a note of it below.

6. Repeat step 4 to ﬁ nd out the other numbers of the

code.

7. When the fourth number has been found, the

indicator lamp goes out.

Check of

the programming

- For a television or a satellite receiver: switch on and,

for example, press 2 to change channels, etc...

- Video recorder: load a tape and then press B.

- DVD player: load a DVD and then press B.

Try other remote control keys to ﬁ nd out the range of

functions you can control. If you think that not all of the

keys are active, try the programming Method B or C.

When you have retrieved the code of

Learning function

If the make of the device you wish to control is not in

the separate code list or if some functions are missing

in the code you have programmed, you can copy

the key functions of the original remote control of

the device into your ROC6411. Depending on the

format of the transmission codes of the original remote

control, your ROC6411 remote control can memorise

up to 150 keys.

Global delete – Delete all the keys copied

(this is recommended the ﬁ rst time you use

this function)

1. Hold down the SETUP key until the indicator lamp

remains lit.

2. Release the SETUP key.

3. Press twice on the LEARN key. The indicator lamp

goes out and then relights.

4. Press once on the SETUP key. The indicator lamp

goes out after several seconds.

5. All the copied keys are now deleted.

Before starting

• The batteries in the 2 remote controls must be in

good condition; change them if necessary.

• First copy 2 or 3 keys from the original remote

control in order to check the compatibility of the

codes of both remote controls. Then carry out a

global delete of these keys before starting the full

learning procedure.

• Lay out the original remote control and your

ROC6411 end to end so as to align the LED

diodes on the 2 remote controls. Where necessary

adjust the height of both remote controls so that the

LED diodes are properly aligned.

• Place the remote controls with the infrared diodes

on a table so that they point each other at a

distance between 15 and 50 mm.

• Do not move the remote controls during the

learning procedure.

• Ensure that the room is not lit by ﬂ uorescents tubes

or low consumption lamps since such light sources

can interfere with the copying.

• The 2 remote controls must be at least one metre

away from any light source.

• Avoid copying VOL and keys codes and the play

keys since depending on the remote controls the

codes of these keys do not necessarily control the

same devices.

• When the memory of your ROC6411 is full,

the mode key will blink for 3 seconds. It is then

not possible to copy any more codes without ﬁ rst

carrying out a global delete.

• When you copy a key, it is possible that the mode

key will blink feebly. In this case, do not release the

key and wait until the blinking stops.

Note 1: if the learning procedure does not seem to

work correctly, try the following:

1. End the learning procedure by pressing SETUP.

2. Check that the LEDs of the two remote controls

are properly aligned. Carry out the alignment

procedure.

Modify the distance between the remote controls, in-

creasing or reducing the distance from 1.5 cm to 5 cm.

4. Restart the procedure from the beginning.

5. If the problem persists and always with the same

key, check that the original remote control is

actually operating: is it sending IR signals? (check

batteries; is it correctly aligned in relation to the

diode on your ROC6411?)

Note 2:

• You cannot copy keys to the LEARN SETUP and

MODE keys.

• All the keys copied to a mode will be deleted if a 4

ﬁ gure code is entered for this mode (and likewise

for direct entry of a code, search of a code or

make).

Identifying the position of the diode on the

original remote control (keys to copy)

If the Infrared LED of the original remote control is not

visible (for example, if hidden behind a dark plastic

plate), the instructions below will help you to locate

it precisely.

1. Place the front of the original remote control (the

part you point at the device to control) around

2.5 cm from the LED of your ROC6411 (see

LEARNING diagram above).

2. Hold down the SETUP key until the indicator lamp

remains lit.

3. Release the SETUP key.

4. Press once on a mode key (TV, DVD, VCR, …).

The indicator lamp goes out and then relights.

5. Press once on the LEARN key.

6. Hold down one of the keys on the original remote

control while moving the remote control from left

to right. As soon as the 2 remote controls are

correctly aligned, the indicator lamp blinks rapidly.

7. To copy the key functions from your original

remote control into your ROC6411, go to step 5

of “To copy keys”.

Note: Some original remote controls don’t transmit

continuous IR signals when a key is held down. If this is

the case, press several times on one of the keys while

moving the remote control from left to right.

To copy keys

1. Hold down the SETUP key until the indicator lamp

remains lit.

2. Release the SETUP key.

3. Press once on the mode key (TV, DVD,

VCR,...).The indicator lamp goes out then relights.

4. Press the LEARN key once.

5. Press once on the key of your ROC6411 to which

you want to copy one of the keys of your original

remote control.

6. Hold down the key of the original remote control

you wish to copy until the indicator lamp goes

out and then relights (2 to 3 seconds). In case

of problems, the indicator lamp will blink for 3

seconds but will remain in learning mode. Try

again or try another key.

7. For the other keys, repeat the procedure from step

5 onwards.

8. Press the SETUP key once when all the desired

keys have been copied. The mode key goes off.

To delete all keys copied under a mode

1. Hold down the SETUP key until the indicator lamp

remains lit

2. Release the SETUP key.

3. Press once on a mode key (TV, DVD, SAT,...).

The indicator lamp goes out then relights.

4. Press twice on the LEARN. key. The indicator lamp

goes out then relights.

5. Press once on the SETUP key. The indicator lamp

goes out. All the keys copied under this mode are

deleted.

AUDIO CODESAT/STB CODEAMP/AUX CODE

VCR CODE

TV CODE

DVD CODE

Method B – 4-digit codes

programming

Before you start programming, you must ﬁ nd the code

of the set to be controlled.

Refer to the list provided with these instructions, page

II of the codes.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the indicator lamp

blinks and then remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp ﬂ ashes to signal that this time is almost up,

and then goes off).

3. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player, VCR: Video

recorder, SAT/STB: satellite receiver, cable, DVBT,

ADSL, AMP/AUX: AUDIO equipment and any

other appliance.

4. While the indicator is lit, enter the ﬁ rst digit of the

4-digit code proposed for the set to be controlled

(example: 0166 for a Thomson TV).

5. Direct the remote control towards the set and try to

switch it off by pressing the key G.

6. Should the set not switch off, repeat step 2. Then

type in the next 4-digit code. Try to switch off the

set by pressing key G once. Repeat this procedure

by trying out each of the 4-digit codes.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands. Check your remote control for

proper functioning by performing the test described

on page 3.

your set, jot it down so that you can use it

whenever needed.

After battery replacement, you may have to

programme the remote control again.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands. Check your remote control for

proper functioning by performing the test described

on page 3.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC6411 6in1 Universal Remote Control in the language / languages: All languages as an attachment in your email.

The manual is 2,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thomson ROC6411 6in1 Universal Remote Control Manual

Product: