Manual Thomson ROC4239 4in1 (page 2 of 34) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

607851

Zoom out

Zoom in

1/34

ROC

4239

STB

DVD

AUX

CR2032

ROC4239

This universal remote control (4 in 1) is compatible with the majority of television sets, DVD pla-

yers and video recorders, as well as digital boxes such as satellite or cable receivers, DVBT recei-

vers (Digital Video Broadcast Terrestrial), ADSL decoders, and so on.

This remote control was programmed in the factory, so that you can use it to control most of the

sets of the THOMSON group’s make. For this reason, we recommend that prior to attempting to

programme the remote control, you try it out by means of one of the methods described in this

user manual. However, ﬁ rst of all, please activate the remote control by removing the 2 protective

tabs from the 2 CR 2032 batteries.

Please keep this guide along with the code list (provided separately), so that you can subsequent-

ly programme your remote control for use with other sets.

1: On/Standby or Standby only, depending on

the equipment being used.

2 Mode keys: Select the device to control

(TV, DVD, …).

3 Setup: Allows you to program your remote before

the ﬁrst use. It also allows you to access to

secondary functions of certain A/V

appliances (Shift). Press and release the

„Setup“ key followed by the function key you

want.

4 Learn: Used for the learning codes procedure (key

copying) (see page 3).

5: Displays information of the selected

appliance.

6: Teletext On.

7: Teletext Off.

8: Teletext Hold (stop page scrolling).

9 Exit: Turn off the menu of the selected

product.

10 (Mute): Switches the selected appliance sound

off.

11 Menu: Turns on the menu of the selected

product.

12 V-, V+: Increases (+) or decreases (-) the volume

of the selected device.

13 P+, P-: Channel Up and Channel Down buttons.

14: Allow you to navigate the menus

horizontally and verticaly.

15 OK: Conﬁrms a selection.

16 (play): Play a DVD disc (DVD)*.

17: Fast forward (DVD)*.

18 (rewind): Goes backward (DVD)*.

19 (pause): Suspends play and stops on an image*.

20 (record): To record, press the RECORD key twice.

21 (stop): Stop the disc (DVD)*.

22 Numeric keys 0 - 9: These keys have the same

functions as those of your original

remote and are also used to enter the

codes for different products.

23 -/--: In connection with the numeric keys, this

button allows you, with some equipment,

to select directly channels with 2 digits.

24 AV: For selecting an external source (SCART,

HDMI, ...).

* The coloured buttons can be used to select

categories when teletext is activated, and speciﬁc

functions depending on the make.

The keys

Testing the remote control before

you programme it

1. Turn on the product you want to control.

2. Press the Mode key that corresponds to the type of

product you want to control:

TV: television set, DVD: DVD player, SAT: satellite

receiver, AUX: any other equipment.

3. Direct the remote control towards your equipment

and try to switch it off by simply pressing the

key G. If the device does not turn off, you must

program the remote control using one of the

methods A, B, C or D described hereafter.

Note 1: Except for the TV key, the DVD, SAT and AUX

mode keys can be programmed to control a device

other than that indicated on the key. It is therefore

possible, for example, to allocate SAT mode to the

DVD key. You must enter the code corresponding to

the manufacturer and the device by using one of the

methods indicated in this manual.

However, method D (automatic search for a code)

will greatly simplify the task for you. In this case it

is only necessary to enter a code from the list that

corresponds to the type of device, for example: 0603

for a Thomson satellite receiver) and then to run the

automatic search procedure. The remote control will

then test all the codes automatically until it ﬁnds those

that control the receiver.

Note 2: To control 2 devices of the same type and the

same brand (2 Thomson AUXs, 2 Thomson satellite

receivers, ...) ensure ﬁrst that these two devices are

not set to react to the same sub code, they will require

one sub code for one and a different sub code for

the other (i.e., codes A and B with Thomson devices).

Once you have checked this, successively program 2

separate mode keys using method D.

Programming

the remote control

Method A – Fast programming

with 1-digit subcode

Before you start programming, you must ﬁnd the

subcode of the set to be controlled. Entering a

subcode lets the remote control test a predeﬁned list of

codes. Refer to the list provided with these instructions,

page I of the subcodes.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the key that

corresponds to the last mode you selected blinks

and then remains lit (the indicator light remains on

for a few seconds to give you the time to proceed

with the following steps. The indicator lamp ﬂashes

to signal that this time is almost up, and then goes

off).

3. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player, SAT: satellite

receiver, cable, DVBT, ADSL, AUX: any other

appliance.

4. While the indicator is lit, type in the subcode

(example: 1 for THOMSON).

5.Direct the remote control towards the set and try to

switch it off by pressing the key G.

6.If the set you want to control switches off, press OK

to memorise the code.

7. Should the set not switch off, press key G repeatedly,

until the set switches off. Between two key presses,

leave enough time for the key corresponding to the

selected mode enough time to light up again (about

1 second). Proceeding this way will enable you to

see whether the set responds or not.

8.Immediately upon the switching-off of the set to be

controlled, press OK to store the code.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Method B – 4-digit codes

programming

Before you start programming, you must ﬁnd the code

of the set to be controlled.

Refer to the list provided with these instructions, page

II of the codes.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the key that

corresponds to the last mode you selected blinks

and then remains lit (the indicator light remains on

for a few seconds to give you the time to proceed

with the following steps. The indicator lamp ﬂashes

to signal that this time is almost up, and then goes

off).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC4239 4in1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thomson ROC4239 4in1 Manual

Product: