607826
3
Zoom out
Zoom in
Previous page
1/3
Next page
3
1. S witch on the COMBO you want to control.
2. Hold down the S (4) until the indicator lamp (1)
remains lit (the indicator light remains on for a few
seconds to give you the time to proceed with the
following steps. The indicator lamp flashes when this
time is almost up, and then goes off).
3. Press the TV (3) key, then follow one of the
programming methods (A, B, C or D) described
earlier.
4. I f a second code programming is required, then repeat
steps 2 and 3 above.
4 - How to retrieve
a programmed code
It may be useful to retrieve the code programmed in the
remote control.
1. Hold down the S (4) key until the indicator lamp (1)
remains lit (the indicator light remains on for a few
seconds to give you the time to proceed with the
following steps. The indicator lamp flashes when this
time is almost up, and then goes off).
2. P ress the key (3) that corresponds to the type of
equipment you want to control:
TV: television set,
VCR/DVD: video cassette recorder, DVD player.
3. Press S (4) again briefly. The indicator lamp (1)
flashes once.
4. Press the number keys (0 to 9) in ascending order
until the indicator lamp (1) flashes once.
5. The digit which made the indicator lamp (1) flash, is
the first number of the 4-digit code. Please make note
of it.
6. R epeat step 4 to find out the other numbers of
the code.
7. When the fourth number is found, the red indicator
lamp (1) goes off.
5 - Check of the programming
- F or a television or a satellite receiver: switch on and, for
example, press (18) to change channels.
- D VD player: load a DVD and then press PLAY (10).
Tr y other remote control keys to find out the range of
functions you can control. If you think that not all of the
keys are active, try the programming Method B or C.
When you have retrieved the code of your set, jot
it down so that you can use it whenever needed.
After battery replacement, you may have to
programme the remote control again.
6 - Other functions
Adjustment of ALL volume controls under a
specific mode.
Yo u can allocate the volume control to one of the modes
of the remote control on condition that the volume
control exists on the corresponding device (e.g. control of
TV sound in VCR/TV mode).
1. H old down the S (4) key until the indicator
lamp (1) remains lit.
2. Release the S (4) key.
3. P ress the c (6) key. The indicator lamp (1)
flashes once.
4. P ress once on the mode key (TV, VCR/DVD…)
corresponding to the device whose volume will always
be controlled by the VOL (7) and c (6) keys.
5. Press the c (6) key once.
Adjustment of the volume controls for EACH
mode.
Yo u can decide that the volume control is functional for
each mode selected on condition that the volume control
exists on the corresponding device (e.g. control of the
television set sound in TV mode, the control of the sound
of the SAT receiver in SAT mode, ...).
1. Hold down the S (4) key until the indicator
lamp (1) remains lit.
2. Release the S (4) key.
3. Press the c (6) key. The indicator lamp (1)
flashes once.
4. Press once on the mode key (TV, VCR/DVD…)
corresponding to the device whose volume will always
be controlled by the VOL (7) and c (6) keys.
5. Press the VOL - (7) key once.
6. Press the c (6) key once.
7 - The NAVILIGHT system
The THOMSON NAVILIGHT navigation system allows you
easy access to the settings of your television set (TV) or your
video recorder (VCR) fitted with the THOMSON NAVILIGHT
system provided that you have allocated the VCR/DVD key
to the video recorder.
1. S witch on the set you want to control.
2. P ress the key corresponding to the type of set you
want to use (TV or VCR/DVD). In the VCR/DVD
position, make sure that the AV mode is activated for
the TV set (the SCART socket must be selected).
3. Press the S (4) key once and then press the a (19)
key.
4. N avigate through the setting menus with the play keys
p, q, t and u (18 and 7).
5. Validate with OK (6).
6. T o leave the menus, press key EXIT (5) once.
Note: The S (4) key remains on as long as light I is lit. If this
light goes out, you have to press the S (4) key again before
using the navigation keys. To exit this mode, press S (4) a
second time.
ROC 2206 / EN / aws - rst / 11-2006
GB
TV CODE VCR/DVD CODE
Yo u can contact THOMSON by dialling:
0871 500 0520
(call to this number
will be charged at 10 pence per minute)
www.thomsonlink.com
01_ROC2206_GB.indd 3 30/11/06 16:56:22
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson ROC2206 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC2206 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thomson ROC2206

Thomson ROC2206 User Manual - German - 3 pages

Thomson ROC2206 User Manual - Dutch - 3 pages

Thomson ROC2206 User Manual - French - 3 pages

Thomson ROC2206 User Manual - Spanish - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info