Manual Thomson ROC Z107 (page 5 of 90) (All languages)

699750

Zoom out

Zoom in

1/90

5.1 Manual code search

Your Universal Remote Control is equipped with an

internal memory,which is preloaded with up to

350 codes per device type for the most common

TV/STB devices. Youcan zap through these codes

until the device you want to control shows a

reaction. This might be that the device you want to

control switches off (POWER key) or changes the

channel (CH+/CH- keys).

5.1.1 Turn on the device you want to control

5.1.2 Press and hold the device button which you

want to control (e.g. TV) for 3seconds until

the LED is on.

5.1.3 Press the “POWER” or the CH+/CH- key to

zap through the preloaded codes until the

device you want to control reacts.

5.1.4 Press MUTE to save the code and exit the

code search. The LED indicator turns off.

Note

► Internal memory limitations allow only up to 350

most common device codes to be preloaded.

Due to the extensive number of different availa-

ble TV/STB devices on the market, it may be pos-

sible that only the most common main functions

areavailable. If so, repeat steps 5.2.1 to 5.2.5 to

nd amorecompatible code. No code may be

available for some special device models.

5.2 Auto Code Search

Auto Code Search uses the same preloaded codes

as the Manual Code Search (5.2) but your Universal

Remote Control scanns through the codes automa-

tically until the device you want to control shows

areaction. This might be that the device you want

to control switches off (POWER key) or changes the

channel (CH+/CH- keys).

5.2.1

Turn on the device you want to control.

5.2.2 Press and hold the device button which

you want to control (e.g. TV) until the LED

indicator ash once and then keep on.

5.2.3 Press the CH+/CH- keys or POWER to start

the Auto Code Search. The LED indicator

ashes once followed by permanent light.

The Universal Remote Control has alatency of

6seconds beforethe rst scan starts.

Note: Scan Speed Settings

► Scan Speed Settings can be set at either 1or

3seconds. The default setting for the scan

time per single code is 1sec. If this feels un-

comfortable ,you can switch to 3sec. scan

time per single code. To switch between the

scan times, press CH+ or CH- during the

6sec. latency beforeAuto Code Search starts

scanning.

5.2.4 The LED indicator conrms each single code

scan with asingle ash.

5.2.5 Press MUTE to save the code and exit the

code search. The LED indicator turns off.

Note

► When all codes aresearched without suc-

cess, the Universal Remote Control exits

Auto Code Search and returns to operational

mode automatically.Currently stored code

is not changed.

5.3 Code Identification

The Code identication offers you the possibility,to

determine an already entered code.

5.3.1 Press and hold the device button until the

LED indicator ash once and then keep on.

5.3.2 Press button ”AV” two times.

5.3.3 LED indicator ashes times means the code.

Like code 1234, LED indicator will ash once

and pause approx.2s, ash two times and

pause approx.2s, ash 3times and pause

approx.2s, then ash 4times and pause

approx.2s. (Number 0and number 1both will

ash once, but number 0will ash very fast).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC Z107 in the language / languages: All languages as an attachment in your email.

The manual is 1,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thomson ROC Z107 Manual

Product: