607829
3
Zoom out
Zoom in
Previous page
1/3
Next page
1. Tu rn on the COMBO you want to control.
2. Hold down the SETUP (11) key until the red
indicator lamp (1) remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp flashes when this time is almost up,and then
goes off).
3. Press the TV (2) key, then follow one of the
programming methods (A, B, C or D) described
earlier.
4. If second code programming is required then repeat
steps 2 and 3 above.
4 - How to retrieve
a programmed code
You may want to retrieve the code programmed in the
remote control.
1. Hold down the SETUP (11) key until the red
indicator lamp (1) remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp flashes when this time is almost up,and then
goes off).
2. Press the product key (2) that corresponds to the
type of product you want to control:
TV:television set, DVD:DVD player,
SAT:satellite receiver.
3. Press SETUP (11) again briefly. The red indicator
lamp flashes once.
4. Press the number keys (0 to 9) in ascending order
until the red indicator lamp (1) flashes once.
5. The digit which made the red indicator lamp (1)
flash, is the first number of the 4-digit code.Please
make note of it.
6. Repeat step 4 to find out the other numbers of the
code.
7. When the fourth number is found, the red indicator
lamp (1) goes off.
5 - Check the programming
-For a television or a satellite receiver:turn on and
off, then try to change channels using a digit key (9).
-DVD player: load a DVD and then press PLAY (B)
(18).
Tr y other remote control keys to find out which
functions you can control. If you think that not all of the
keys are active, try the programming Method B or C.
When you have retrieved the code of your product,
make note of it.
After battery replacement, you may have to
programme the remote control again.
6 - Controlling volume in
satellite and cable mode
Adjustment of ALL volume controls under a
specific mode.
Yo u can allocate the volume control to one of the
modes of the remote control on condition that the
volume control exists on the corresponding device
(e.g. control of TV sound in VCR/TV mode).
1. Hold down the SETUP (11) key until the
indicator lamp (1) remains lit.
2. Release the SETUP (11) key.
3. Press the MUTE (15) key. The indicator lamp (1)
flashes once.
4. Press once on the mode key (TV, VCR/DVD…)
corresponding to the device whose volume will
always be controlled by the VOL (4) and MUTE
(15) keys.
5. Press the MUTE (15) key once.
Adjustment of the volume controls for EACH
mode.
Yo u can decide that the volume control is functional for
each mode selected on condition that the volume
control exists on the corresponding device (e.g. control
of the television set sound in TV mode,the control of
the sound of the SAT receiver in SAT mode,...).
1. Hold down the SETUP (11) key until the
indicator lamp (1) remains lit.
2. Release the SETUP (11) key.
3. Press the MUTE (15) key. The indicator lamp (1)
flashes once.
4. Press once on the mode key (TV, VCR/DVD…)
corresponding to the device whose volume will
always be controlled by the VOL (4) and MUTE
(15) keys.
5. Press the VOL (4) key once.
6. Press the MUTE (15) key once.
7 - The NAVILIGHT system
The THOMSON NAVILIGHT navigation system allows you
easy access to the settings of your television set (TV) or your
video recorder (VCR) fitted with the THOMSON
NAVILIGHT system provided that you have allocated the
DVD or SAT keys to the video recorder.
1. Switch on the product you want to control.
2. Select the type of product concerned (TV, DVD or
SAT). In the DVD position, make sure that the AV
mode is activated for the TV set (the SCART socket
must be selected).
3. Press the SHIFT (3) key once and then press the
MENU (5) key.
4. To travel through the setting menus, press the up,
down, left, right keys (4 and 14).
5. Confirm with OK (15).
6. Exit the menus by pressing the EXIT (16) key.
Note:The SHIFT (3) key remains on as long as light I is
lit. If this light goes out, you have to press the SHIFT key
again before using the navigation keys.To exit this mode,
press SHIFT a second time.
EN
3
ROC 3205 / EN - pp - PB / aws - rst / 12-2006
TV CODE
DVD CODE
SAT CODE
Yo u can contact THOMSON by dialling:
0871 500 0520
(call to this number
will be charged at 10 pence per minute)
www.thomsonlink.com
01-ROC3205_en.qxp 15/12/06 15:27 Page 3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson ROC 3205 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC 3205 in the language / languages: English as an attachment in your email.

The manual is 0,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thomson ROC 3205

Thomson ROC 3205 User Manual - German - 3 pages

Thomson ROC 3205 User Manual - Dutch - 3 pages

Thomson ROC 3205 User Manual - French - 3 pages

Thomson ROC 3205 User Manual - Spanish - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info