582477
8
Zoom out
Zoom in
Previous page
1/24
Next page
EN 8
English
Chapter 3 - Installing channels
Initial setup
Initial setup involves selecting all the settings required
to be able to search for and store all the analogue
and digital channels you can receive.
Make sure that the television is switched on and
follow all the steps in turn specied hereafter.
Note: If the channel search retrieved only the
analogue channels it could be caused by poor
broadcasting and therefore is not covered
by manufacturer warranty. Manufacturers
cannot be held responsible for lack of or poor
broadcasting in some areas.
The rst time you switch the set on, the Initial setup
wizard opens, which guides you through the initial
setup process. (Refer to Figure 1.)
Initialsetup
Please select your language:
Language
English
Български
Hrvatski
Čeština
Dansk
Select Next
Nederlands
Figure 1
1. Press ▲/▼ to select your language, then press
OK/► to enter the next step.
2. Press ▲/▼ to select your country, then press
OK/► to enter the next step. Press ▲/▼ to select
your location, then press OK/► to enter the next
step. Press ▲/▼ to select to continue or skip
network connection setup, then press OK/► to
enter the next step.
Note: If you select France or Italy, you will have
to enter the Password setting menu here
to set a password. Use the alphanumeric
buttons to enter a four-digit number for your
password. (0000 is too simple to be set as your
password.) Re-enter the same code to conrm
the password. After that, you will enter the next
step automatically. (In this step, you can only
press to return to the previous step.)
3. Press ▲/▼ to select your tuner mode
Antenna or
Cable or Satellite.
(Note:
Satellite option may not be available for
certain models.) Then follow a) or b) or c) below.
- a) If you have selected
Antenna.
Press OK/► to enter.
Press ▲/▼ to select Digital & Analogue or
Digital or Analogue, then press OK/►.
Press ▲/▼ to select Scan, then press OK/►
to start the automatic search for all DVB-T
digital and/or analogue channels.
Note: not all countries have Favorite Network
Selection function.
- b) If you have selected
Cable.
Press OK/► to enter.
Press ▲/▼ to select Digital & Analogue or
Digital or Analogue.
If you select Digital & Analogue, press OK/►
to enter. Then:
- Press ▲/▼ to select Scan, then press OK/►.
- Press ◄/► to select the scan mode if
available (Full or Advanced).
- If you select Full, press OK to start the
automatic search for all DVB-C digital and/or
analogue channels.
- If you select Advanced, use the numeric
buttons to adjust the values for frequency,
symbol rate, network ID, and use ◄/► to
select the modulation mode; then press OK
to start the search for all DVB-C digital and/or
analogue channels.
If you select Digital, press OK/► to enter,
then follow all the same steps as for Digital
& Analogue above, to search for all DVB-C
digital channels.
If you select Analogue, press OK/► to enter,
press ▲/▼ to select Scan, then press OK/► to
start the search for all analogue channels.
- c) If you have selected
Satellite.
Press OK/► to enter.
Press ▲/▼ to select one operator and press
OK/►.
Press ▲/▼ to select one satellite, then press
OK to congure the proper information related
to this satellite. Press OK to go back after
nishing settings.
Press ► to start scanning.
Note: To prevent the channel setup process from
being interrupted, wait for the message
indicating that the setup is complete.
4. Before starting the scanning, you can also select
Skip scan to skip the initial setup process. In this
case, to search and store your channels you may
do an automatic channel search by following the
instructions in the next section Performing an
automatic channel search.
5. During the setup, you can follow the hints available
at the bottom of the screen to return to the
previous step by pressing ◄. Or press EXIT to exit
or interrupt the search halfway.
6. In this step, you can press OK to exit the initial
setup. The channels are arranged in a preset
order. If you wish to skip channels, modify the
preset order or rename channels, select Setup >
Organiser and press OK/► to enter. In this step,
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson 55UZ8766 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson 55UZ8766 in the language / languages: English as an attachment in your email.

The manual is 4,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info