471997
4
Zoom out
Zoom in
Previous page
1/10
Next page
EN 4
Initial setup
Initial setup involves selecting all the settings required
to be able to search for and store all the analog and
digital channels you can receive.
Make sure that the television is switched on and
follow all the steps in turn specied hereafter.
Note: TV channels search retrieved only the analog
chanels could be caused by poor broadcasting
and therefore is not covered by manufacturer
warranty. Manufacturer cannot be held
responsible for lack or poor broadcasting in
some areas.
The rst time you switch the set on, the Initial setup
wizard opens, which guides you through the initial
setup process. (Refer to Figure 1.) Press OK to start
your initial setup.
1. Press ▲/▼ to select your language, then press
OK/► to enter the next step.
2. Press ▲/▼ to select your country, then press
OK/► to enter the next step.
Note: When select France, you will have to
enter the Password setting menu here
in order to set a password. Use the digit
buttons to enter a four-digit number for your
password. (0000 is too simple to be set as
your password.) Re-enter the same code
to conrm the password. After that, you will
enter the next step automatically. (In this
step, you can only press to return to the
previous step.)
3. Press ▲/▼ to select your tuner mode Air or
Cable.
- Select Air.
Press OK/► to enter.
Press ▲/▼ to select Scan, then press OK/► to
automatically start the search relating to initial
setup for all DVB-T digital and analog channels.
- Select Cable.
Press OK/► to enter.
Press ▲/▼ to select Scan, then press OK/►
to directly start your initial setup or enter below
step.
Select Full if available to search for and store
all DVB-C digital and analog channels.
You may select other advanced scan mode if
available (for example, Advanced or Quick),
then congure proper cable information as
described below. Use the digit buttons to
adjust the values of frequency, symbol rate
and network ID; use ◄/► to select certain
modulation mode.
Press OK to start initial setup relating to all
DVB-C digital and analog channels.
Note: To prevent the channel setup process from
being interrupted, wait for the message
indicating that the setup is complete.
4. Before start the scanning, you can also select Skip
scan to skip the initial setup progress.
5. During the setup, you can follow the hints available
at the bottom of the screen to return to the previous
step by pressing ◄. Or press Exit to exit or
interrupt the search halfway.
6. Once the automatic search ends, the set enters
the next step automatically. You can press ▲/▼ to
select your location Shop or Home. Press OK/► to
conrm your selection and enter the last step.
7. - In this step, you can press OK to exit the initial
setup. The channels are arranged in a preset
order. If you wish to skip channels, modify the
preset order or rename channels, select
Setup > Organiser and press OK/► to enter.
- In this step, you can also press ◄ to return to the
previous step.
Automatically install channels
This section describes how to search and store
channels automatically. Instructions are for both
analog and digital channels.
1. Press Menu on the remote control and select
Setup > Language > Menu language. Press
◄/► to select your desired menu language.
2. Press Menu to return to Setup, press ▲/▼ to
select Country, then press ◄/► to select your
country. The TV installs and arranges channels
according to your country.
3. Press ▲/▼ to select Tuner mode, then press
◄/► to select Air or Cable.
- Select Air.
Press ▲/▼ to select Channel install, and
press OK/► to enter.
Select Automatic search (Refer to Figure 2.),
then press OK/► to display Automatic search.
Press OK to skip the country selection and
enter the next step. Or use ◄/► to reselect
your country, then press OK to enter.
Select Digital & Analog, Digital or Analog,
then press OK/► to start the automatic search,
which relates to all DVB-T digital and/or analog
channels.
- Select Cable.
Press ▲/▼ to select Channel install, and
press OK/► to enter.
Select Automatic search, then press OK/► to
display Automatic search.
Press OK to skip the country selection and
enter the next step. Or use ◄/► to reselect
your country, then press OK to enter.
- Select Digital & Analog, then press OK/► to
enter. Select your scan mode if available and
congure proper cable information in the same
way as in Initial setup. Select Scan and press
Install channels
Chapter 2
English
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson 24FT5253 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson 24FT5253 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info