Manual Thomas INOX 1420 Plus (page 9 of 24) (English, German, Dutch, French, Italian)

485813

Zoom out

Zoom in

1/24

Assembly Instructions

Dear client,

thank you very much for your confidence.

You have made the really good choice:

The Thomas Wet & Dry Vacuum-Cleaners are

always usable for optimal cleaning task in your

private workshop, cellar and garage.

The Wet & Dry models INOX 1420 plus/1520 plus

and INOX 1520 S are delivered with a 20-liter

stainless-steel dirt collecting bin, and enhanced

motor casing with protection against splash water.

If this appliance brings you entire satisfaction, we

would be grateful to you to recommend us. We

prefer this sort of promotion to a big luxurious

advertising campaign.

Assembly Instructions

A + B Assembling the chassis

Place the chassis ring upside down on a

stable surface.

Drive the shafts by the ribbed end into the

bore marked with the number 4 on the chassis

ring.

Then push the wheels in as far as they will

go. Turn the collecting bin upside down (i.e.

opening facing the floor).

Place the chassis ring on the collecting bin in

such a manner that one of the castor wheels

stand directly in line with the suction socket.

Then press the chassis ring firmly until it snaps

into place.

C Fitting the motor block

Place the motor block onto the collecting bin,

making sure that the operating switch lies

directly in line with the middle of the suction

socket.Lastly, secure the motor block by means

of both snap fasteners.

D Connecting the flexible hose

Connecting the flexible hose. Remove the

hose by turning the hose connecting piece

and withdrawing the hose.

Assemble the accessoires you require.

Connect the main cable.

Operating the appliance

The MultiVac is switched on and off by means

of the switch located on the motor block

casing.

The mains supply voltage must correspond to

the voltage given on the rating plate.

E Changing the cartridge filter

(Optional extra, Part no. 787021/421)

Pull out the plug!

Depending on the model type, the retaining

clips are either already pre-mounted or must

be fitted according to the enclosed Assembly

Instructions F.

Undo the snap fasteners, remove the motor

block from the collecting bin and turn over.

Secure the cartridge filter by the pre-mounted

retaining clips.

Place the new cartridge filter in an upright

position on the motor flange and gently but

firmly slide it into place on the filter mounting.

The pre-mounted retaining clips automatically

snap into place, thus securing the cartridge

filter. Place the motor block on the collecting

bin again and secure by means of the snap

fasteners.

F Inserting the paper filter bag

(when changing the paper filter bag)

Place the filter bag inside the collecting bin,

making sure that the opening located in the

cardboard inlay is placed in line with the

suction soket.

Then press the filter bag evenly

around the sides of the collecting bin.

Thomas paper filter bags are essential

when vacuuming fine dust, e.g. soot, ashes,

sawdust or cement. However, they are also

recommended for normal use, as they not

only improve the retention of dust, but also

make filter changes more hygienic.

Changing the cartridge filter

Gently pull the retaining clips back in the

direction indicated and carefully remove the

cartridge filter in an upright position from the

filter mounting. Clean the soiled cartridge

filter under running water – if necessary, with

a brush.

Drain and allow to dry thoroughly before

using again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thomas INOX 1420 Plus in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thomas INOX 1420 Plus Manual

Product: