576911
12
Zoom out
Zoom in
Previous page
1/15
Next page
12
The performance of this appliance meets the requirements of the European Standard
for Domestic Cooking Appliances (EN30) which specifies a maximum allowable
temperature rise of the furniture into which the appliance is installed of 65
o
C above the
ambient temperature. The installer should verify all furniture materials are suitable – ie
plastic materials may have a softening point lower than specified above.
We recommend the installation follows the minimum dimensions shown in this manual
as any deviation could result in excessive temperature rise. If minimum dimensions
must be reduced, due to design constraints, a temperature rise test of all furniture fitted
around the unit MUST be performed. The design is deemed permissible providing the
results of this test comply with all standards in force and the requirements detailed
within the furniture manufacturer’s material specification. Where minimum dimensions
are reduced we recommend protecting with non combustible material.
Gas Connection
Prior to connection ensure the local conditions for gas type and gas pressure match the
appliance specification. (Gas type and pressure for this appliance are printed on the
databadge located on the base of appliance)
The Ø8mm gas inlet is located to the rear of the appliance. Prior to connection remove the
plastic protection plug from the fitting. The appliance MUST be connected using metal pipe
manufactured from either copper, seam welded steel, seamless steel or stainless steel,
which complies to the requirements of EN1949. Rubber tubing MUST NOT be used.
Electrical Connection
Spark Ignition (12V DC)
The spark ignition generator MUST only be connected to a suitable 12V DC supply. We
recommend connecting to the generator using sheathed spade connectors.
Dual Fuel models
(230-240V ~ 50Hz)
Models fitted with power cord only
This appliance is supplied with a double insulated cord, type 227 IEC 53, HO5V V-F, which
is suitable for use up to 4 amps. This should be connected to a double pole switched
mains supply, with 3mm minimum contact separation at all poles in accordance with the
wiring rules. Ensure that all electrical cables and wires are routed well clear of any heat
source, including this appliance. Do not allow the cord to hang loose into the lower
compartment. The switch must be accessible after installation.
Models fitted with plug and power cord (UK only)
This appliance is supplied with a plug attached to the end of the power cord, for
connection to a switched wall mounted socket. After connection ensure the power cord
and any other electrical wires are routed well clear of any heat source, including this
appliance. Do not allow the cord to hang loose into the lower compartment. The switched
socket must be accessible after installation.
INSTALLATION
If the power cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thetford S-OH77000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thetford S-OH77000 in the language / languages: English as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thetford S-OH77000

Thetford S-OH77000 User Manual - German - 17 pages

Thetford S-OH77000 User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info