576908
14
Zoom out
Zoom in
Previous page
1/15
Next page
14
1. Disconnect from gas supply
Lift and remove the bottom plinth to gain access, then disconnect the gas supply.
If the appliance is Dual Fuel, disconnect/isolate the electric supply.
2. Remove hob surface
Disconnect from gas supply (1) and electric supply if Dual Fuel. Lift off the Panrest
and remove the two screws securing each burner spreader. Remove front fascia by
removing all push on control knobs and unscrew the two recessed fixed nuts and
both fascia retaining screws. Carefully lift off the fascia and if spark ignition fitted
remove the two spade connectors from the rear of the toggle switch. Remove the
two central screws securing the pressing to the rear box section. Remove the two
front retaining screws located each side and accessed through the outer slots on
the angled front. Grasp the hob by the angled front face, carefully lift the hob
surface from the front to allow the rear edge to unhook from the rear box section.
Note:- On Dual Fuel appliances, remove the hotplate rear cover and disconnect the
power leads. The hob surface should be put onto a suitable surface.
3. Remove appliance from housing
Disconnect from gas supply (1). Open the oven door and remove the 2 screws from
each side trim - note the appliance can either be front or side fixed, see under
Fixing, page 12. Open the glass lid and remove the 2 screws from each side trim.
Carefully slide the appliance out one third and check for any possible snagging of
wires or pipes. If the appliance is Dual Fuel, disconnect supply lead from rear
terminal block. If OK, lift appliance out onto a suitable surface.
4. Control replacement
Hob controls
Disconnect from gas supply (1). Remove hob surface (2). Unscrew the
corresponding pipe and thermocouple and remove from the control.
Remove the locknut from the front of the control panel. Disengage the control from
the gas rail and remove.
Oven and Grill control
As above instructions but remove appliance from housing to gain access to the
oven thermostat, grill and oven thermocouples. Open the oven door and unscrew
the 2 screws holding the thermostat probe in position and push the probe back out
through the hole in the rear of oven. Remove the retaining screws from on top and
underneath the control. Disconnect the inlet pipe and two burner supply pipes.
Remove the fittings off the old control and fit on the replacement.
5. Remove the grill burner
Disconnect from gas supply (1). Remove appliance from housing (3). Remove hob
surface (2). Remove the two screws retaining the heat deflector. Remove the
insulation wrap and remove the three grill flue retaining screws – two beneath the
fascia panel, one located on top rear of flue cover. Lift off the flue cover. Lever off
starlock washers retaining the grill burner.
6. Spark Ignition (where fitted)
Disconnect from gas supply (1). Remove appliance from housing (2).
Grill burner – At rear of appliance remove the screw from the bracket and spark
ignition probe. Trace the electrode wire back to the generator and pull off the
connector.
Oven burner - Trace the electrode wire up the back of the cooker to the generator
and pull off the connector. Unscrew the fixing screw on the spark electrode inside
the oven cavity, then carefully pull the electrode from inside the oven and remove.
Piezo Spark Generator replacement - Remove all electrode wires. Remove the
lock nut and carefully remove from panel.
SERVICING
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thetford S-OH70000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thetford S-OH70000 in the language / languages: English as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thetford S-OH70000

Thetford S-OH70000 User Manual - German - 17 pages

Thetford S-OH70000 User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info