771210
12
Zoom out
Zoom in
Previous page
1/78
Next page
1.9
Switch off the power before removing the cover, to avoid any risk
of injury or electric shock.
1.10
The installation must be equipped, upstream of the appliance, with
a bipolar cut-out device (fuse, breaker switch) respecting local
regulations (30 mA earth-leakage breaker).
1.11
If the supply cord is damaged, it must be replaced by a special cord
or assembly available from the manufacturer or the after sales
service.
1.12
Mandatory installation of a safety device in a frost free location
(or any other new device which limits the tank pressure) to 0.7 or
0.9 MPa (7 or 9 bar) according to the nominal pressure, with a size
of ½" or ¾" on the input of the water heater, respecting the local
regulations (see table p.2).
1.13
Operate regularly the discharge of safety device to prevent scaling
and check that it is not blocked.
1.14
Hydraulic accessories should not be located between the safety
valve and the cold water inlet. A pressure reducer (not supplied) is
required when the water supply pressure exceeds 0,5 MPa (5 bar)
and will be fitted on the main supply.
1.15
Connect the safety device to an unpressurised outlet pipe in a frost
free location, with a continuous slope to evacuate water during
heating up or draining the water heater.
1.16
The pipes used must support 1 MPa (10 bar) and 100 ° C.
1.17
Always connect the earth conductor of the cable to the earth
ground wire or connect the earth conductor to the appropriate
terminal identified by the symbol .
1.18
To drain the device: Switch off the power and the supply of cold
water, open the hot water faucets and manipulate the safety valve.
To drain under sink water heater disconnect the hydraulic
connections and return the device.
1.19
NOTE: For under sink models, disconnect hydraulics and return to
empty.
1.20
These devices comply with the directive 2014/30/UE
according to electromagnetic compatibility, 2014/35/UE according
to low voltage, 2011/65/UE according to ROHS directive and
Commission Delegated Regulation 2013/814/UE supplementing
2009/125/EC regulation for ecodesign.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermor Premium at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermor Premium in the language / languages: English, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1.99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info