600941
17
Zoom out
Zoom in
Previous page
1/37
Next page
17
DHW temperature display
If any other variable is displayed at the moment (heating water temperature, output, error message etc.),
pressing any of the buttons 2 opens the DHW temperature dialogue. This display is indicated by the °C pilot
light above button 4.
In the case of sensor defect or absence, the numerical data become replaced with dashes: _ _ _ during disconnection or interruption of the
sensor or wiring, ¯ ¯ ¯ after a short circuit on the sensor or wiring.
Displaying and change (setting) of the desired DHW temperature value
If you press any of the , buttons (2) with the display showing the DHW temperature dialogue, you can
set its desired value. The setting process is indicated by flashing of the °C pilot control above the
O/I
(ENTER)
button (4). You can set the desired temperature value by pressing the , button (2) within the
range defined by the TU_ a TU¯ (P3.5 a P3.6) items of the service menu. The set value does not need to be
confirmed. The setting mode for the required values terminates 15 seconds after any of the , (2) buttons
has been last pressed.
The desired DHW temperature value can be set only if the rtU DHW heating mode is set to b_c (P3.2 = 2) (storage tank with the
temperature sensor).
Switching the heating on or off
The heating mode can be switched on or off by pressing the
O/I (MENU)
button (3). The on-mode is
signalled by the pilot light between , buttons (1); the pilot light in the off-mode is turned off.
Heating can be switched on only if its operation is pre-set in the user menu; the rto item must be set to tEr, EtE, Prt, otP or ot- (P3.1 =
1 – 5).
Switching the DHW heating on or off
The DHW heating mode can be switched on or off by pressing the
O/I (ENTER)
button (4). The on-mode
is signalled by the pilot light between , buttons (2); the pilot light is off if the DHW is in the off-mode.
The DHW heating can be switched on only if its operation has been pre-set in the service menu; the rtU item must be set to b_n or b_c
(P3.3 = 1 or 2).
Displaying the outdoor/room temperatures
To display any other operational variables (except for the heating water and DHW temperatures), use the
(SELECT)
button (5). If you press (or double press) it, the outdoor/room temperature display dialogue opens.
This dialogue is indicated by the IN/OUT °C pilot light.
In the case of sensor defect or absence, the numerical data become replaced with dashes: _ _ _ during disconnection or interruption of the
sensor or wiring, ¯ ¯ ¯ during short circuit of the sensor or wiring
The difference between displaying the room or outdoor temperature rests only in the location of the sensor. Shall the boiler operation be
controlled on the basis of its data, the respective mode must be selected in the user menu:
- for rto = EtE (P3.1 = 2) (integrated equitherm regulation) outdoor sensor must be used,
- for rto = Prt (P3.1 = 3) (integrated room thermostat) sensor in the room of reference must be used.
If the sensor is connected but the boiler operation is not controlled on the basis of its data, these data are used at least for protecting the
system against freezing.
Displaying the heating system pressure
If you press (or double press) the
(SELECT)
button (5), the system pressure dialogue opens. This display
dialogue is indicated by the bar pilot light.
Minimum operation pressure of the system is 0.5 bar.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermona THERM EL 45 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermona THERM EL 45 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info