600939
16
Zoom out
Zoom in
Previous page
1/37
Next page
16
Adr P6.2
MULTIPLE BOILER FORMAT (CASCADE) CONTROL PARAMETER
h.01-h.21
ERROR HISTORY DISPLAY
i.01-i.12
SERVICE AND DIAGNOSTIC INFORMATION
7. Boiler control and display of basic operational information
(more detailed user instructions)
Heating water temperature display
After its connection to the power network, the display shows heating water temperature in °C which is
indicated by the pilot light °C above the
O/I (MENU)
button (3). If any other variable is displayed at the
moment (DHW temperature, output, error message etc.), pressing any of the buttons , (1) opens the
heating water temperature dialogue.
In the case of sensor defect, the numerical data become replaced with dashes: _ _ _ during disconnection or interruption of the sensor or
wiring, ¯ ¯ ¯ after short circuit on the sensor or wiring.
Displaying and changing (setting) the desired temperature of heating water
If you press any of the , buttons (1) with the display showing the heating water temperature dialogue,
you can display its desired value. Slow flashing of the °C pilot light above the
O/I (MENU)
button (3) shows
the desired value. The currently valid desired temperature value according to the operational mode is displayed
(e.g. calculated by means of the integrated equitherm regulator or integrated room thermostat by way of a
communication line from the external regulator).
If you press any of the , buttons (1) with the display showing the desired heating water temperature,
you can set the desired value. Faster flashing of the °C pilot light above button 3 indicates the setting process.
The desired temperature value can be set by means of , buttons (1) within the range defined by TO_ a
TO¯ (P3.4 a P3.5) items in the service menu. The set value does not need to be confirmed. The mode of setting
the desired value terminates 15 seconds after any of the , buttons were last pressed (1).
The set desired value is valid in the following situations:
- rto heating mode is set to tEr (P3.1 = 1) (control performed by contact of the external room thermostat),
- rto heating mode is set to EtE (P3.1 = 2) (equitherm regulation) but the outdoor temperature sensor defect has been reported,
- rto heating mode is set to Prt (P3.1 = 3) (integrated room thermostat) but the room temperature sensor defect has been reported,
- rto heating mode is set to otP or ot- (P3.1 = 4 or 5) (external OpenTherm protocol regulation) but communication has failed.
PARAMETERS SET FOR THE MASTER CASCADE BOILER
PCC P7.1
NUMBER OF BOILERS IN THE CASCADE
dCC P7.2
SYSTEM CASCADE PUMP DECELERATION
dC1 P7.3
BOILER PUMP DECELERATION, IN THE CASCADE, AFTER ITS HEATING
OPERATION IS FINISHED
AFC P7.4
CASCADE SYSTEM ANTI-FREEZE PROTECTION FREEZE
PhC P7.5
MAXIMUM CASCADE OUTPUT WITHOUT MRC SIGNAL
P0C P7.6
MAXIMUM CASCADE OUTPUT AT DISCONNECTED CONTACTS OF RELAY 1
AND 2
P1C P7.7
MAXIMUM CASCADE OUTPUT AT CONNECTED CONTACT OF RELAY 1
P2C P7.8
MAXIMUM CASCADE OUTPUT AT CONNECTED CONTACT OF RELAY 2
P3C P7.9
MAXIMUM CASCADE OUTPUT AT CONNECTED CONTACTS OF RELAY 1
AND 2
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermona THERM EL 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermona THERM EL 30 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info