Manual Thermona THERM EL 15 (page 10 of 37) (English)

600937

Zoom out

Zoom in

1/37

 mount a heating system charge and discharge cock and a sludge cock at the lowest point of the system

in the very proximity of the electric boiler

 separate all electric boiler types on inlet and outlet by stop valves, too (see standards CSN 06 8030), not

to be forced to discharge the whole system in case of inspection or repair of the boiler or during filter

replacement

 remove control levers from stop valves and secure them against manipulation.

♦ Boiler connection to electric network

Wiring can be installed only by an authorized person in the sense of the Decree No. 50/1978 Coll. on

professional qualification in electrical engineering. Certification of the boiler installation and putting into

operation must be noted in a proper manner on the letter of guarantee. Any interference with internal boiler

wiring (with the exception of wiring specified in this Manual, e.g. the external regulator connection instead of

jumper wire) are inadmissible!

The boiler control box must be connected according to the relevant CSN standard by means of a

separately protected line which enables its disconnection and which is located in the very proximity of the

electric boiler!

Current protective switch must be used if the electric boiler is installed in a bathroom.

The power wiring is connected by a 5-conductor system to the U, V, W, N and PE terminals. In the case of a

4-conductor system the N and PE terminals shall be connected together and the power wiring matched with the

U, V, W and PE terminals.

If MRC is connected to the boiler control box, the MRC receiver outlet is matched with the terminal marked

HDO/N.

WARNING! When using the MRC receiver signal on the HDO/N terminal, it must be made sure that all

contactor coils of other appliances (e.g. of the boiler if it is connected to the common MRC signal) are

energized with the same phase!

When operation must be delivered also outside the so-called “low tariff”, the maximum boiler output

limit can be switched off in the service menu also without the MRC signal (P4.4)!

Recommended cable cross sections under the plaster:

Boiler output [kW] 8 15 23 30 38 45

Power take-off [A] 12 24 36 48 60 72

PVC insulated cable with copper

conductors 5 [sq.mm]

2,5 4 6 10 16 25

♦ Charging the heating system

For the duration of the heating system charging, the boiler must be unplugged from the electric network by

disconnecting it by the main circuit breaker. It is useful to maintain the level of filling pressure in a cold system

in the range between 1 and 1.5 bar. Filling must proceed slowly in order to let the air bubbles escape through

the respective valves. According to CSN 07 7401 the water used for the first filling as well as for refilling must

be clear, colourless, without any suspended substances, oil or chemically aggressive admixtures, with a

minimum carbonate hardness (max. 3.5 mval/l) and it cannot be acidic (pH cannot be below 7). Only approved

agents can be used for water hardness adjustments.

HDO is the Czech abbreviation for MRC: translator's note.

I Have an EL15 and cannot see how to connect a 3 way motorised valve. Manual shows position on diagram but how is connection physically made? Please help Submitted on 28-9-2022 at 18:47
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thermona THERM EL 15 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thermona THERM EL 15 Manual

Product: