607240

Thermocet Trimline 140 -1039 Manual

24
Zoom out
Zoom in
Previous page
1/41
Next page
Page.24
* Now determine the installation and assembly of the CC ducts and accessories. Please refer to Chapter 7
“Concentric flue system” on page 11 and the “Table of concentric pathways” on page 28.
* Install the Mertik control Box (12) in your chosen installation location.
Please note:
The distance between the control cabinet and the unit will be determined by the cable lengths from
the control cabinet to the pilot burner and the gas block etc. and how all these items are installed.
The max. distance is 800 mm (see also page 32 and 33 figures 1 to 5). The pipes, cables and/or cou-
plings etc. should only be connected when the electricity supply is off.
* It is also possible to install the fireplace using fireproof sheets
* The slats, log inset / pebbles or Carrara stones may now be installed.
MAKE SURE THE PILOT LIGHT REMAINS UNOBSTRUCTED!
* Before reinserting the window, check whether or not a restriction plate needs to be installed.
See page 20 and the “Table of concentric pathways” on page 28.
* If a restriction plate is required for your installation situation, remove the baffle plate (13) by un screw-
ing the front of the plate (see page 34 figure 7) and then sliding the plate backwards and taking it out.
Now install the restriction plate (14) using the two supplied screws and reinsert the baffle plate.
11.4 Fitting the ceramic log inset 1035, 1036, 1037, 1038 and 1039 (see pages 37, 38 and 39)
Please note: when installing the log inset and the various glowing materials and accessories, the fol-
lowing must be taken into account:
A: There should be no glowing material in or on the pilot burner.
B: Ceramic materials should not come into contact with the cord of the window fixture.
Remove this if necessary. The window may otherwise be damaged.
* Mix the glowing material (lava granules) and the “fusilli” (spiral-shaped ceramic material) and spread
them evenly over the burner and the burner plate so that they are just covered. Glowing embers can be
placed here and there as decoration.
NOTE: the remaining material can be discarded. The use of too much glowing material can adversely af-
fect the combustion process (see also notes A and B above)
* Then insert the logs in the correct order as shown on pages 37, 38 and 39.
* Position the log inset carefully. Different positions may have a significant influence on the flame image or
cause poor functioning of the burning process (explosion).
11.5 Fitting the optional pebble set (see page 40 figure 10)
* Scatter vermiculite evenly over the burner tray. Make sure the pilot light remains unobstructed.
* Place a row of medium-sized and large pebbles at the front of the burner plate
* Insert the pilot light protective cage in the 2 sockets to the left and right of the pilot light.
* Fill the burner tray with small and medium-sized pebbles from the front to the rear. Place the pebbles as
closely as possible to each other on the burner tray.
* Fill the rear of the burner plate with medium-sized and large pebbles.
* Reinstall the window, following the instructions for removing it in reverse order.
11.6 Fitting the optional Carrara stones (see page 40 figure 11)
* Scatter vermiculite evenly over the burner tray. Make sure the pilot light remains unobstructed.
* Insert the pilot light protective cage in the 2 sockets to the left and right of the pilot light.
* Fill the burner tray neatly and evenly with the Carrara stones.
* Reinstall the window, following the instructions for removing it in reverse order.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermocet Trimline 140 -1039 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermocet Trimline 140 -1039 in the language / languages: English as an attachment in your email.

The manual is 2,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info