659030

Thermocet Trimline 120 DB Tunnel - 1138 Manual

7
Zoom out
Zoom in
Previous page
1/125
Next page
Page.6
Note: when installing the log and Pebble set and the various glowing materials and accessories, the fol-
lowing must be taken into account:
A: No glowing material in or on the pilot burner.
B: Prevent that ceramic material falls on the glass seals. Remove this if necessary. The window can be damaged.
C:
Slot /opening between burner and mesh deco plate must be kept free of glowing material. Too
much placed glowing material can affect the combustion process.
Before placing the log set when heating on G25 20-25mBar (I2L / I2ELL) the premix brackets underneath
the double burner needs to be changed. (see APPENDIX 5 image 8)
4. PLACEMENT OF THE CERAMIC LOG AND OPTIONAL PEBBLE SET
Method:
* Loosen the screws holding the bottom and top glass holders (see APPENDIX 5).
* Place the suction cup(s) in the middle of the glass-panel and remove the panel by GENTLY
moving this first upwards and then the lower edge of the glass-panel very carefully and slowly
pulling toward you. Then place in a safe place where the window can not be broken or damaged.
If the removed glass panel is damaged (scratched and / or damaged edges) then no longer use the
glass panel and contact your dealer.
* Remove the deco plate and double burner out of the burning chamber.
* Unscrew both premix brackets from the burner.
* (1135/1136/1139/1149) Place the premix bracket for (G25) G20-25 met 2X Ø4 mm.
* (1137/1138/1048) Place the premix bracket for (G25) G20-25 met 2X Ø4,5 mm.
* Place screws back in place.
* The burner pressure and the injector need not be changed. Replace the Burner and the decorative plate.
4.1 Fitting the Ceramic log set (see APPENDIX7)
* Mix the glowing material (lava granules) and spread them evenly over the burner and the burner
plate so that they are just covered. Glowing embers can be placed here and there as decoration.
* Place the ceramic wood blocks in the correct order as shown on APPENDIX 7.
* Place the logs carefully. Other location can seriously affect the flames or malfunction of the
burn process (sooting)
* Before replacing the windows make sure if there must be a restriction plate to be placed or not.
See chapter 8 "Concentric chimney lay out"
* If there is a restriction required for your situation, remove the baffle plate by unscrewing it
from the front of the plate and move the plate backwards and then out. Now install the restriction
plate with two screws and replace the baffle plate. (Also see APPENDIX 5-7).
* Now place the window in reverse order as described at chapter “PLACING THE APPLIANCE” 2.2 and
on APPENDIX 5.
4.2 Fitting the optional Pebble set. (see APPENDIX8)
* Scatter vermiculite evenly over the burner tray. Make sure the pilot light remains unobstructed.
* Place a row of medium-sized and large pebbles at the front of the burner plate
* Fill the burner tray with small and medium-sized pebbles from the front to the rear.
Place the pebbles as closely as possible to each other on the burner tray.
* Fill the rear of the burner plate with medium-sized and large pebbles.
* Before replacing the window make sure if there must be a restriction plate to be placed or not.
See chapter 8 "Concentric chimney lay out"
* If there is a restriction required for your situation, remove the baffle plate by unscrewing it
from the front of the plate and move the plate backwards and then out. Now install the restriction
plate with two screws and replace the baffle plate. (Also see APPENDIX 5-7).
* Now place the window in reverse order as described at chapter “PLACING THE APPLIANCE” 2.2 and
on APPENDIX 5.
2.6 Fitting the Carrara / Basalt stones (see APPENDIX 8)
* Scatter vermiculite evenly over the burner tray. Make sure the pilot light remains unobstructed.
* Fill the burner tray and burner plate neatly and evenly with the Carrara stones.
* Reinstall the window, following the instructions for removing it in reverse order.
* Before replacing the window make sure if there must be a restriction plate to be placed or not.
See chapter 6 "Concentric chimney lay out"
* If there is a restriction required for your situation, remove the baffle plate (see APPENDIX 5)
by unscrewing it from the front of the plate after the plate backwards and then out.
Now install the restrictor plate with two screws and replace the baffle plate.
* Now place the window in reverse order as described at 2.2 on APPENDIX 5.
MAKE SURE THE PILOT LIGHT REMAINS UNOBSTRUCTED FROM ANY MATERIAL!
NOTICE
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermocet Trimline 120 DB Tunnel - 1138 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermocet Trimline 120 DB Tunnel - 1138 in the language / languages: English, German, Dutch, Danish, French, Spanish as an attachment in your email.

The manual is 6,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thermocet Trimline 120 DB Tunnel - 1138

Thermocet Trimline 120 DB Tunnel - 1138 Installation Guide - Dutch - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info