Manual Thermocet Trimline 120 -1037 (page 9 of 41) (English)

607238

Zoom out

Zoom in

1/41

Page.9

5. INITIAL START-UP

The unit has a layer of heat-resistant varnish that resists very high temperatures. An unpleasant smell may de-

velop in the first hours after starting the unit due to burning in of the varnish; however, this is not dangerous. To

accelerate this process, allow the unit to burn at the highest setting for several hours and ventilate the area well.

After the first time the unit is turned on, a light deposit may form on the inside of the window. This is due to the

varnish hardening. After the fireplace has cooled down, this deposit can be removed using a fireplace glass

cleaner or ceramic hotplate cleaner.

5.1 Daily maintenance

* Avoid having a lot of dust and cigarette smoke, candle and oil lamp particles in the air of your home.

Heat ing of these particles through the convection system of the unit, can lead to discolouring of walls and

ceilings. It is therefore advisable to ensure the area containing the unit is always sufficiently ventilated.

Regularly remove any dust that has settled behind the operating lid with a vacuum cleaner.

If the glass is broken or cracked, it should be replaced immediately by a recognised fitter before the

unit is used again.

* The unit must be switched off immediately if something is spilt on it. It should only be cleaned once the

unit has cooled down. Never use abrasive, aggressive cleaning products or fireplace cleaner; only use a dry

cloth that does not give off fluff.

* Your local specialised dealer will be able to provide you with spray cans containing heat-resistant varnish,

so that small stains or damages may be touched-up during annual maintenance.

5.2 Important tips for gas heating or wood fuelled units and fireplaces.

Prevent discolouration of walls and ceilings!

There are always particles in the air in each living area even if the area is vacuum cleaned regularly!

These particles are easily visible when the sun streams in. This issue will not arise if the amount of particles in

the air is limited. If these particles are present in greater quantities and particularly if the air is contaminated by

soot and tar particles, for example, through the burning of candles or oil lamps and cigarette or cigar smoke, then

we can speak of a poor inner climate! Cooled air slowly flows over the floor to the heater in a heated living area.

This air is heated in the convection system of the fireplace or heater, resulting in a quickly rising column of air

that subsequently spreads through the room again. This means there is always dust and other polluting particles

depositing on cold and often damp surfaces. This issue occurs especially in a new building (building damp) that

is not yet dry. An undesirable consequence of this phenomenon could be discolouration of walls and or ceiling!

How can this problem be avoided?

* With a newly built fireplace or following renovation, wait at least 6 weeks before firing up.

* The building damp must have disappeared completely from the walls, floor and ceiling.

* The room where the unit is located must be well ventilated.

* The required air ventilation must be in line with local building regulations.

* Limit the use of candles and oil lamps and keep the taper as short as possible.

* These two creators of atmosphere ensure considerable quantities of polluting and unhealthy soot particles

in your house.

* Among other things, cigarettes and cigars contain tar that will precipitate on cold and damp walls during

heating.

* This may occur above radiators and light fittings and with ventilation grilles (if there is a poor internal

climate), although to a lesser degree.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thermocet Trimline 120 -1037 in the language / languages: English as an attachment in your email.

The manual is 2,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thermocet Trimline 120 -1037 Manual

Product: