659028
91
Zoom out
Zoom in
Previous page
1/125
Next page
g.18
No ACCIÓN POSIBLE PROBLEMA/CAUSA SOLUCIÓN
6.
NO
Alta resistencia en el
termopar.
Controlar cables, conexiones y
termopar.
Unidad magnética
se apaga (se
escucha un “clic”)
Termopar no se calienta
lo suficiente.
Controlar si la llama piloto toca el
termopar. Ajuste la llama piloto si
es necesario.
Motor gira a la posición
principal de encendido y
la llama piloto
permanece encendida.
Corriente en el termopar
débil.
Controle las conexiones y si es
necesario reemplace el termopar.
¡No esfuerce las conexiones!
Corto producido por
daño en la punta del
termopar.
Reemplace el termopar. ¡No
esfuerce las conexiones!
NO
Proceso de encendido se
detiene. El recibidor no
responde al mando a
distancia. (el recibidor no
reacciona)
Presione el botón RESET. Ver
instrucciones.
Conecte un cable adicional entre
el quemador de la llama piloto y el
bloque regulador de gas.
SI
No enrolle el cable de encendido.
Recorte el cable de encendido si
es posible.
7.
Quemador se enciende
NO
Ubique manualmente el
botón del bloque
regulador de gas en
posición MAN.
Gire el botón a la posición ON.
SI
8.
Quemador permanece
encendido.
NO
Le llega mucha/poca
ventilación a la llama
piloto, se apaga/se
ahoga
Controlar si la placa contratiro está
bien colocada. Ver instrucción.
Ductos mal posicionados:
controlar el trayecto del ducto y
sus conexiones.
SI
9.
Unidad magnética se
apaga mientras que el
motor sigue
funcionando
3 veces “pip”
NO
Las pilas del recibidor
están en mal estado
Reemplace las pilas, 4x 1,5V AA.
¡Calidad alcalina!
El sistema se puede
apagar desde el mando
a distancia
N
O
El sistema se puede
apagar usando los
interruptores ON/
OFF
NO
Corto entre TC y el cable
SW.
Controlar las conexiones al
interruptor.
SI
SI
OK
OK
Cambie el bloque
regulador de gas.
91


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermocet Trimline 100 DB Tunnel - 1135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermocet Trimline 100 DB Tunnel - 1135 in the language / languages: English, German, Dutch, Danish, French, Spanish as an attachment in your email.

The manual is 6,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thermocet Trimline 100 DB Tunnel - 1135

Thermocet Trimline 100 DB Tunnel - 1135 Installation Guide - Dutch - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info