607258

Thermocet Estilo Manual

12
Zoom out
Zoom in
Previous page
1/32
Next page
Page 12
7.2 Construction of concentric flue system CC
Assembly instructions are provided below:
Direct connection.
∗ The unit can be connected directly to an exterior wall using the exterior wall duct set, taking any hindrance
to the surrounding area into consideration, according to national, regional, local standards and regulations.
Ensure wind pressure on the flue terminal is not too extreme, such as a balcony, flat roof, corners and in
small alleys etc., as this may negatively influence the unit efficiency.
∗ Provide a recess in the exterior wall of around 155 mm (in a flammable wall ensure there is 50mm of extra
space around the outer pipe) and fix the wall duct with the wall plate to the inner side of the wall.
∗ The wall plate of the exterior wall duct must be sealed adequately against the wall on the outside, to avoid
potential moisture and/or flue gas leaks into the living space.
∗ The flue should be cased if necessary. Sufficient fireproof measures must also be taken when the flue is be-
ing mounted along flammable materials.
∗ Determine the position of the unit and the outlet and begin construction of the flue with the connection on
the unit, paying attention to the direction of installation. The inner flue must be installed for draining pur-
poses. Connect the elements by using clamping strips.
Indirect wall connection.
∗ The outlet may also be installed above the exhaust in the wall, taking any hindrance to the surrounding area
into consideration, according to national, regional, local standards and regulations. Ensure wind pressure on
the flue terminal is not too extreme, such as a balcony, flat roof, corners and in small alleys etc., as this may
negatively influence the unit efficiency.
∗ Provide a recess in the exterior wall of around 155 mm (in a flammable wall ensure there is 50mm of extra
space around the outer pipe) and fix the wall duct with the wall plate to the inner side of the wall. The wall
plate of the exterior wall duct must be sealed sufficiently against the wall on the outside, to avoid moisture
and/or flue gas leaks into the living space.
∗ The flue should be cased if necessary. Sufficient fireproof measures must also be taken when the flue is be-
ing mounted along flammable materials.
∗ Determine the position of the unit and outlet and begin construction of the flue with the connection on the
unit, paying attention to the direction of installation and connecting the elements by means of clamp strips.
∗ Mount a 90° bend directly on the wall pass-through and connect with the elements on the unit. Ensure that
all connections are gastight.
∗ The fitted pipe can be used between the bends or when connecting to the unit.
L= 50 - 250 mm. If necessary, use wall brackets to support the flue.
Comments:
The outlet vent may need to be mounted close to the wall in some situations. In this case, the 90° bend cannot be
easily placed. Note that at the location of the 90° bend where the bend has the smallest radius, an oval hole needs
to be created in the wall to ensure good passage.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermocet Estilo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermocet Estilo in the language / languages: English as an attachment in your email.

The manual is 3,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info