607254
6
Zoom out
Zoom in
Previous page
1/26
Next page
Page 6
Setting first period of heating.
Press the button B4 (3x) until P 1 and
) appears on the display.
Press button B4 for slightly longer until the start time begins to flicker and appears and set the time for the start of the first period of
heating by means of the buttons B1and B2 ; hours/minutes.
Press button B4 again so that P 1 and ) appears after which the time can be set to the end of the first period of heating by means of the
buttons B1and B2 ; hours/minutes.
Press button B4 for slightly longer until the display P 2 and
* appears and set the time for the start of the second period of heating by
means of the buttons B1and B2 ; hours/minutes.
Press button B4 again so that P 2 and ) appears after which the time can be set to the end of the second period of heating by means of
the buttons B1and B2 ; hours/minutes.
Wait or press button timer again and the display will return to the start.
2.2 Igniting the apparatus
* Press buttons B1and B3 at the same time until an acoustic signal indicates that the start procedure has
begun for igniting the apparatus. Once the ignition of the pilot burner has been achieved the gas block will
set the flame height automatically to maximum.
* You can regulate the flame height by pressing on button B1 or B2 for higher or lower flame height
respectively. In order to set the apparatus on “Standby” you press on button B2 until just the pilot burner is
burning.
Warning
Wait at least 5 minutes before attempting to re-ignite the unit after turning off the pilot. Gas fires become hot
when in use. Therefore care should be taken, for instance children and those requiring help should be kept away
from the immediate area where the fire is burning. Gas fires must not be placed on or against flammable materi-
als (curtains, etc.).
2.3 Technical data:
Radio controlled Transfer Frequency:
ON 40.5 kHz, OFF 40 kHz
Range: 0.5…10m
Ambient temperature:
Transmitter and receiver: max. 60ºC
Connection cables: max. 180ºC
Maintenance
The painted parts can be wiped with a soft, moist cloth. The unit must be switched off immediately if something
has been spilled on the fire. Once the fire has cooled down the spillage can be removed with water and soft soap.
Never use an abrasive cleaning agent!
Any deposits on the glass can be removed by using a glass cleaner. We recommend having the fire and the chim-
ney checked by a fitter and having them cleaned before each heating season. If the special heat-resistant glass is
broken or cracked it should be replaced immediately before the unit is switched on again.
It is better to leave the pilot burning during the heating season (due to possible condensation formation in the
unit).
Please note: As the manufacturer we are aware that faults may occur in the electronic control of gas fires and the
great inconvenience this may cause you. Therefore we have drawn-up additional installation instructions. (See
pages 18 and 19.)
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermocet Beverly S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermocet Beverly S in the language / languages: English as an attachment in your email.

The manual is 3,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info