Manual Texas ST1301 (page 13 of 35) (English, German, Danish, Finnish)

636772

Zoom out

Zoom in

1/35

Front handle

Loosen the knob and lift up the handle bar to the operation position. (Fig. 2)

Adjust the height of the handle to a safe and comfortable position and fix it by the knob.

Connection the mains (Fig. 3)

Loop the extension cord and feed it through the rear handle. Rest the cord around the cord hook. This will help prevent

you from disconnecting the extension cord from the product during operation.

Warning! Do not handle the plug or the appliance with wet hands or while standing in water.

DANGER! Electric shock causes series injury and death!

Starting

Intend use

This appliance is only intended for sweeping of snow on steps, patios and decks in private domestic and hobby gardens.

It is not designed for use in public areas, parks, sports areas, and in agriculture and forestry.

Using the application only on hard, flat surfaces free of sad, stone and debris, wires and any other objects.

For any other purpose is considered incorrect and unapproved. The manufacturer is not liable for any damage or injury

resulting from such use. The user is entirely responsible for any associated risks.

On/Off switch (Fig. 4)

Warning! The auger starts rotation immediately after switch on! Keep hands and feet away from auger.

To switch ON, hold the appliance firmly with two hands and press the Safety lock off button (2) while press the On/Off

switch trigger (3).

Keep the switch trigger hold while release the button.

To stop the appliance, release the switch trigger and it automatically returns to its start position.

Removing snow

 Before starting work, make sure that the area to be clear is free of stones, debris, wires and any other objects.

 Make sure all fasteners (screws, nuts, etc.) are always fully tightened so that you can work safely with the

appliance.

 Check the auguer for wear and tear at regular intervals.

 Position discharge chute in safe direction and angle, away from operator and bystanders.

 Clearing snowfall often, before it gets too deep. Snow is best removed as soon as possible after snow falls.

 Lift the auguer off surface slightly before switch on.

 Switch on and tilt the appliance forward until the scraper blade contacts the ground. Push the appliance forward at a

comfortable rate of speed, yet slow enough to clear the path completely. The width and depth of the snow

determines your forward speed.

 Direct the snow to the right or to the left by holding the appliance at a slight angle. For the most efficient snow

removal, throw the snow downwind, and slightly overlap each swath.

 The appliance can remove snow up to 12 cm deep in one pass. When clearing deeper drifts, hold the appliance by

the upper and lower handles and use a swinging or sweeping motion. Shaving off the top layer and making multiple

passes (Fig. 5).

For large areas, a definite pattern of operation is required to thoroughly clean an area of snow. These patterns will avoid

throwing snow in unwanted places as well as eliminating a second removal of snow. (Fig. 6)

Pattern A: Throw the snow to the right or left side where it is possible, as on a long driveway it is advantage to start in the

middle. Plow from one end to the other, throwing snow to both sides.

Pattern B: If the snow can only be thrown to one side of the driveway or sidewalk (above), start on the opposite side.

 Scraping the snow all the way down to the pavement will wear out the scraper and auger. To spare the machinery,

one or two inches of snow can be left behind, to be handled with de-icing salt or a shovel.

 After clearing the snow, let the motor run for a few minutes so that the ice doesn’t freeze any moving parts. Then

switch off the motor, wait for all moving parts to stop, and wipe the ice and snow off the appliance.

Warning! To avoid serious personal injury, do not use hands or feet to unclog chute.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Texas ST1301 in the language / languages: English, German, Danish, Finnish as an attachment in your email.

The manual is 0,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Texas ST1301 Manual

Product: