636771

Texas ST1300 Manual

14
Zoom out
Zoom in
Previous page
1/35
Next page
14
Maintenance and Storage
Before carrying out any maintenance operations, cut off the electric power supply by disconnecting
the plug from the extension cable.
Regular cleaning and maintenance of your appliance will ensure efficiency and prolong the life of your appliance.
After each operation, take apart and clean out the ice and debris from the ventilator and its slot, auger and
housings.
Only use a cloth soaked with hot water and a soft brush to clean the application. Never wet or spray water on the
machine!
Do not use detergents or solvents as these could cause irreparable damage to your appliance. Chemicals can
destroy the plastic parts.
To protect the application from corrosion when storing for a longer period, treat the metal parts with harmless oil to
the environment.
Store the appliance in a dry room out reach of kids.
Change of belt (Fig. 7, 8)
The drive belts (34) and (35) need to be replaced depends on wear and tear.
Drive belt (35)
Undo screws and take off the cover (39).
Remove screw, washer and pulley frame (38), and the belt (35) from the pulleys.
Install the new belt in the same pathway as the old one. Drive belt (34), small
Loosen the nut and take the pulley (24) off with the belt (34) off the shaft.
Remove the retaining ring (21), washer and pulley (33) if necessary.
Reinstall belt (35), pulley frame (38) and the cover.
Auger (Fig. 9)
Caution! Check fasteners before each operation. Loosen auger result extra vibration and damage to the appliance.
To change the auger:
Remove cover (39), pulley frame (38) and belt (35).
Loosen the nut from other side of auger (42) and dismount the pulley (37) and auger axle (41).
Replace the auger with a new one.
Scraper blade (Fig. 10)
Scraper blade is a wear item and should be replaced when necessary. Wear scraper blade invite extremely vibration and
damage of auger.
Undo 3 screws.
Replace with a new one.
Troubleshooting
Warning! Before any maintenance work, first switch off the appliance and unplug from the mains.
Motor does not start
Mains failure. Check the mains if the same as described in the technical data.
Connections problem. Check electrical connection and make sure the operation of the switch is turned on
correctly.
Poor snow throws
Drive belt worn or damaged. Replace the drive belt.
Auguer worn or damaged. Replace the auguer, check the tighten of screws and nuts.
Blocked discharge. Switch off the appliance and clean the discharge.
Abnormal vibrations
Drive belt worn or damaged. Replace the drive belt.
Auguer worn or damaged. Replace the auguer, check the tighten of screws and nuts.
Scarper blade worn or damaged. Replace the scarper blade, check the tighten of screws.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas ST1300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas ST1300 in the language / languages: English, German, Danish, Finnish as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info