Manual Texas Razor 4680 TR-W (page 16 of 62) (English, German, Dutch, Danish, French, Polish)

636632

Zoom out

Zoom in

1/62

Recoil with choke, speed lever illustration F3-C*

1. By cold engine set the choke lever on ”Choke”- By

warm engine set the choke lever on ”Run”

2. Hold the handlebar for the engine brake; this will

release the engine brake.

3. Pull the recoil starter gently until you feel resistance

in the rope, then pull quickly and energetic. Do not

at any time let go of the recoil starter but slide it

gently into starting position.

4. Return the choke lever in the”run” position. (only

cold engine)

5. Set speed lever in gear from 1 to 4 (C)

6. Hold the bar for self-propelled in order to start

mowing.

* Note: Not all models are equipped with choke lever.

Note: As long as operating the mower, the bar

forengine brake must be engaged.

Throttle lever*

Engine speed can be adjusted while driving. Turn gas

handle to adjust rpm. (ID: M) It is recommended to run

at full throttle for best cutting results.

* Note: Not all models have throttle control

Regulation of speed*

Speed can be adjusted from 2.7 – 5.0 km/h while

driving. Activate the right handle on the dashboard and

set in one of the 4 different speeds. When driving in one

the two lowest speeds the pace difference will not vary

significantly.

* Note: Not all models have speed lever

Stop: Illustration F4

1. Release the engine brake and self-propelled bar to

turn off the mower and the engine

Note: The blades will still rotate at up to 3 seconds

after stopping.

Water nozzle

The left side of the mower deck is fitted with a water

nozzle for washing the deck. (See Illustration ID-F)

• Place the lawn mower on a flat surface that can

tolerate water, and put the height adjustment to

lowest position.

• Attach a hose to the nozzle.

• Turn on the water and start the engine.

• The rotations of the blades will ensure that the

water will clean the underside of the deck.

Note: For best result clean the deck with the water

nozzle function right after each mowing. If the grass

dries out, this function will not work optimally.

Oil change

Oil should be changed for the first time after 2 hours,

then at least 1 time per year.

You will need an oil extractor kit. Art. no. 40-11336

Oil and oil extractor kit is not included

Use an extractor kit and do as follows:

1. Turn on the engine and let it run for 5 min or until

the engine is hot. A hot engine liquefies the oil

which makes it easier to drain.

2. Suck the oil up through the oil filler hole using the

syringe that came with the oil extractor kit. Use the

hose to reach the sump.

3. Transfer the used oil into a empty container.

4. Fill the engine with SAE-30 oil.

5. Check the oil level using the dipstick. (Min / Max)

Remember to dispose the used oil so that it does

no harm to nature.Use your local recycling station.

Air Filter

The air filter should be inspected and cleaned regularly.

If the filter has not been cleaned for a long time, the

engine’s power will drop.

See Illustration A2

1. Clean around the air filter before removing the cap.

2. Push the two flaps down and gently pull the cover

3. Carefully remove the paper filter and inspect it.

Brush it with a soft brush. If it is very dirty, replace

it. Be careful that no dirt gets into the inlet.

4. Wash the black foam element in the right side in

warm water and soap.

5. Press the water out of the foam element and let it

dry. Put a few drops of SAE-30 oil on the filter to

moisten it lightly. Carefully squeeze any surplus oil

out of the foam element and reattach.

6. Please note that all parts are assembled correctly

and properly closed, as shown in the picture.

Blade

Inspection of the blade

• Tilt the mower with the front upwards.

• Inspect blade for damage, cracks or excessive rust

or corrosion.

• Check that the blade bolt is tightened.

Note: A dull blade can be sharpened! But a blade that

is worn, bent, cracked or otherwise damaged must be

replaced.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Texas Razor 4680 TR-W in the language / languages: English, German, Dutch, Danish, French, Polish as an attachment in your email.

The manual is 7,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Texas Razor 4680 TR-W Manual

Product: