709628

Texas Instruments TI-Navigator 3.2 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
5
c
6 7
TI-Navigator™ 3.2 Getting Started poster
Assemble and charge the hubs
Hub batteries are already charged when shipped, but you should charge them overnight before use.
Use AC9940 power adapter to plug
charging bay into a power outlet.
Place hubs in charging bay
to recharge.
Connect network connectors onto hubs.
Or you may use the
AC9930 power adapter
to charge individual
hubs in a power outlet.
TI-Navigator™ System ID
48z6-co2j-cyms-qol2x
(Sample)
Activate access point and hubs
Reminders and next steps
For detailed instructions, see the Installation Guide.
2 3 4
AC9940
AC9930
USB Cable
LEDs
Reset
Install TI-Connect™ and
TI-Navigator™ software
a) Insert the software installation CD in the
CD-ROM drive.
b) When the window opens, click the Computer
Software button, and install TI-Connect™ 1.6
software on the computer.
c) Restart your computer, and open the CD again.
d) Next, click TI-Navigator™ Software, and follow
the instructions on the screen. Click Install
TI-Navigator to install the software.
d) When the installer program asks for it, type the
System ID for your TI-Navigator™ system. You
can find the System ID inside the CD case.
e) Wait and follow the instructions on the screen.
Please follow all the steps as instructed on the
screen. This poster provides an overview; the
Installation Guide provides details.
a) When you are prompted to start the Network
Setup wizard, click OK.
b) Follow the instructions on the screen. Click
Next or Finish as you complete each screen in
the wizard.
c) Plug the power adapter into the Access Point.
For detailed instructions, see the Installation Guide.
Set up your network
a) Continue to follow the instructions on the
screen.
b) Connect the USB cable to the access point.
c) Plug the access point’s power adapter into a
power outlet.
d) Connect the USB cable from the access point
to the computer’s USB port.
AC9930 Power Adapter
AC9930
Set up your network (continued)
• For detailed set-up instructions, see the Installation Guide.
• The driver for the USB Silver Edition cable is included on the
TI-Navigator™ software installation CD.
• Four required Apps must be installed on all the calculators on
the TI-Navigator™ network: NavNet, θAlgACT, θnavstk, and
LearnChk. Use the App Transfer utility under the Tools tab in the
TI-Navigator™ software.
• LearningCheck Creator is an important software tool included on
the CD. You must install it separately from the other software.
• You must upgrade the operating system on your TI calculators
to 1.19 or higher (TI-83 Plus), 2.41 or higher (TI-84 Plus), or 1.90
or higher (TI-73 Explorer™). See the Installation Guide for more
information on upgrading the calculator operating system. (An
operating system may take ten minutes per calculator to transfer
and install.)
• For quick access to information while using the software, see
the TI-Navigator™ Reference Guide or the TI-Navigator™ Help.
a) Follow the wizard’s instructions to activate the
access point.
b) Next, you will add the hubs. When prompted,
insert a ball point pen into the hole at the back of
each hub to press and hold the Reset button.
The hub’s LEDs begin to flash amber.
c) Hold the Reset button until all three LEDs show
solid amber. This may take up to 10 seconds.
After you reset each hub, it may take a few
seconds for the hub’s ID to be added to the list.
If you see this message while installing,
click Yes. The message does not mean
there is a problem.
c
b
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas Instruments TI-Navigator 3.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas Instruments TI-Navigator 3.2 in the language / languages: English as an attachment in your email.

The manual is 4,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Texas Instruments TI-Navigator 3.2

Texas Instruments TI-Navigator 3.2 Additional guide - English - 286 pages

Texas Instruments TI-Navigator 3.2 Installation Guide - English - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info