636696

Texas Hobby 500B Manual

11
Zoom out
Zoom in
Previous page
1/39
Next page
6
Maintenance and storage
The engine shall be stopped when carrying out
maintenance and cleaning operations, when changing tools
and when being transported by means other than under its
own power.
Check regularly that all bolts and nuts are tightened.
Retighten if necessary.
The engine must be completely cooled before storing
indoors or covered.
If the machine unused for a period of time, please refer to
the instructions in this manual.
Maintain or replace safety and instruction labels, as
necessary.
Only use original spare parts or accessories. If not original
parts or accessories is used, the liability is no longer
applied.
Replace faulty silencers.
Miscellaneous
The gears are delivered pre-greased. However, always
ensure they are well greased before each use.
The motor is not pre-filled with oil.
Factory-fitted control devices, such as the handle-mounted
clutch cable, must not be removed or exposed.
Only drain the fuel tank outdoors. Gasoline is extremely
flammable and the fumes are explosive.
Ensure that the machine is properly secured when
transported on a flatbed etc.
Reduce the throttle during engine shutdown and close the
fuel valve.
Assembly
Please follow the steps in figure:
(Actual model may vary from the illustration shown.)
Box content
A. Blades
B. Tiller with cables
C. Support wheel
D. Side guards
E. Upper handlebar
F. Depth skid
G. Lower handlebars, right & left
H. Mounting bracket for steer
I. User manual
1. Mount support wheel. Remove bracket (A). The levers
on the bracket must go behind the rear axle.
2. Mount the bracket over the rear axle to attach the
support wheel.
3. Mount the two lower handlebars with the bolts supplied
(C). Note that the left and right handlebars are different.
Lower handlebar (A) must be mounted on the right.
Lower handlebar (B) must be mounted on the left.
4. Mount upper handlebar using the bolts supplied and the
hand wheel. Note: The arrows on the plastic brackets.
They must be aligned when mounting.
5. Mount throttle cable (A) and clutch cables (B) as shown
on the picture.
6. Mount the blades using the cotter bolts and pins.
7. Mount the side guards using the bolts and nuts supplied.
Note: The sideguards has to go under the yellow body.
8. Mount depth skid with the cotter pin supplied.
Fill the motor with oil.
See changing the oil section for more details.
Clothing
When using the machine, wear close-fitting work clothes,
hard-wearing work gloves, ear defenders and non-slip boots
with steel toecaps.
Operating the tiller
Ensure the machine is placed on a level surface
with the support wheels lowered prior to start.
Remove all foreign objects from the work area
before using the machine. Stones, glass, branches
and similar items may damage the tiller. Also check
the bolts on the tiller are tightened.
Start the motor as per the instructions below. Stand
clear of the machine’s moving parts.
Never attempt to move the machine in any way
other than intended for normal use while the motor
is running.
The tiller is designed for use in vegetable gardens and
flowerbeds. Ensure that you are familiar with these
instructions before operating the machine, in particular the
motor start and stop procedures.
Fig 10: To use the black handle, the control stick must first
be activated. By tilting the control stick to the right or left side
and then activate the black handle, the tiller will move
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas Hobby 500B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas Hobby 500B in the language / languages: English, German, Danish, French, Polish as an attachment in your email.

The manual is 2,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info