Manual Texas Fusion 10TG (page 15 of 32) (English, German, Danish)

636687

Zoom out

Zoom in

1/32

Remove all foreign objects from the work area

before using the machine. Stones, glass, branches

and similar items may damage the tiller. Also check

the bolts on the tiller are tightened.

Start the motor as per the instructions below. Stand

clear of the machine’s moving parts.

Never attempt to move the machine in any way

other than intended for normal use while the motor

is running.

The tiller is designed for use in vegetable gardens and

flowerbeds. Ensure that you are familiar with these

instructions before operating the machine, in particular

the motor start and stop procedures.

Fig. 13A: To use the clutch handle, the control stick

must first be activated. By tilting the control stick to the

right side and then activate the cluth handle, the tiller

will move forward or backwards, depending on the

selected gear (Fig. 15). In order to change gear, the

clutch handle must be released, before a new gear is

selected with the gear rod.

Always release the clutch handle before

changing gear!

Fig. 13B: Adjustment of the speed on the throttle control

can be made without releasing the clutch handle first.

Pay attention while reversing. It is important that the

area is cleared, for any obstacle before reversing.

Never reverse the tiller against a wall, tree or any other

fixed obstacle.

Variable cultivating speed

The rotation speed of the blades is variable. There are

8 different speeds available.

This ensures the best result no matter in which weather

it is being used how however the soil conditions are.

Adjustment of speeds

The gear rod have 5 positions (see Fig. 14 and 15)

N: Neutral (2 positions)

R: Reverse

H: High speed gear

L: Low speed gear

On the throttle control on the handle, there are 5

positions: STOP-1-2-3-4.

Position 1-2-3-4 offer 4 speeds, which can be selected

in both high speed gear (H) and low speed gear (L).

Totally 8 speeds for cultivating and use with different

accessories.

General advises for working speed when

cultivating:

H4 Cultivating the lawn

H3 Cultivating soft soil

H1/L4 Cultivating hard soil

Soft and moist soil:

A relatively high working speed should be used. It

makes the machine work forwards and it is easier to

avoid that the machine is digging itself down.

By using a higher speed, it prevents soil and mud to

stick between the blades and a better cultivating result

will be accomplished.

Hard soil / soil with many stones:

A relatively slow speed should be used. It makes the

machine work downwards and thereby gives a more

steady work with less vibrations.

The exact adjustment of speed, should match the user

and the local conditions.

See Fig. 16 for more recommendations of speed

depending of use.

Variable working width

The working width of the tiller blades can be adjusted

for individual needs.

3 sets of tiller blades are mounted in each side.

Each set can be removed/attached with cotter bolts -

depending on needed working width.

It makes it possible to cultivate in narrow areas between

plants or cultivate bigger areas much faster..

The working width can be adjusted like this:

35 cm Inner blades

62 cm Inner blades + outer blades

68 cm Inner blades + middle blades

90 cm Inner blades + middle blades + outer blades

Operation zone

While the machine is being operated and the motor is

running, do not leave the operation zone marked fig 19.

If it is necessary to leave the operation zone, for

example to attach an accessory, first stop the engine.

It is normally necessary to drive the tiller over a section

of earth 2-3 times from different directions. Do not till

very wet soil, as clods of earth will form that are difficult

to break up.

Adjusting the handlebar

Fig. 10: The handlebar can be adjusted from side to

side by activating the handle (A). Choose the preferred

position and release the handle (A) again.

Fig. 11: The handle height can be adjusted up/down by

releasing the lock handle (B). Choose the preferred

position and press the lock-handle (A) back again.

Adjusting the wheel / depth skid

Fig 12: During operation, it may be necessary to raise

the support wheels, as it is connected to the depth skid.

There are 4 positions.

Raising the support wheels

Raise the depth skid if needed. Press the rod (C)

forward with the foot to release the wheel assembly. Let

the handle fall downwards, so that the wheel assembly

is pushed up into a higher position. Remove the foot

from the rod (C) to lock the wheel assembly into

position.

Lowering the support wheels

Press the rod (C) forward with the foot to release the

wheel assembly. Lift up the handlebar, so that the

wheel falls down into a lower position. Remove the foot

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Texas Fusion 10TG in the language / languages: English, German, Danish as an attachment in your email.

The manual is 5,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Texas Fusion 10TG Manual

Product: