Manual Texas Fusion 10TG (page 14 of 32) (English, German, Danish)

636687

Zoom out

Zoom in

1/32

Ensure a stable foothold and always keep a firm

hold on the handles. Always walk, never run.

Do not operate the equipment when barefoot or

wearing sandals.

Exercise extreme caution when changing direction

on slopes

By rear tillers, ensure that the blades are protected

by safety shield, only the part of the blades that

works into the soil must be free.

Never attempt to make any adjustments, while the

engine is running.

Use extreme caution when reversing or pulling the

machine backwards

Never operate the engine indoor or in areas with

low ventilation. The exhaustion from the engine

contains carbon monoxide. Failure to observe

could result in permanent injury or death.

Gasoline safety

Use extreme care in handling gasoline. Gasoline is

extremely flammable and the fumes are explosive.

Serious personal injury can occur, when gasoline is

spilled on yourself or your clothes. Rinse your skin

and change clothes immediately!

Use only an approved gasoline container. Do not

use soft drink bottle or similar!

Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

Never refuel your machine indoors.

Let the engine cool down before refilling

Never fill the fuel tank to more than 2.5 cm below

bottom of filler in order to provide space for fuel to

expansion.

After refueling, ensure that the cap tighten

securely.

Never use the lock-function on the gasoline gun,

when refueling.

Do not smoke while refueling.

Never refuel inside a building or where gasoline

fumes may get in contact with an ignition source.

Keep gasoline and engine away from appliance,

pilot lights, barbecues, electric appliances, power

tools, etc.

If the fuel tank has to be drained, this shall be done

outdoors

Maintenance and storage

The engine shall be stopped when carrying out

maintenance and cleaning operations, when

changing tools and when being transported by

means other than under its own power.

Check regularly that all bolts and nuts are

tightened. Retighten if necessary.

The engine must be completely cooled before

storing indoors or covered.

If the machine unused for a period of time, please

refer to the instructions in this manual.

Maintain or replace safety and instruction labels, as

necessary.

Only use original spare parts or accessories. If not

original parts or accessories is used, the liability is

no longer applied.

Replace faulty silencers.

Miscellaneous

The gears are delivered pre-greased. However,

always ensure they are well greased before each

use.

The motor is not pre-filled with oil.

Factory-fitted control devices, such as the handle-

mounted clutch cable, must not be removed or

exposed.

Only drain the fuel tank outdoors. Gasoline is

extremely flammable and the fumes are explosive.

Ensure that the machine is properly secured when

transported on a flatbed etc.

Reduce the throttle during engine shutdown and

close the fuel tap, if this exists on the engine.

Assembly

Please follow the steps in figure:

(Actual model may vary from the illustration shown.)

1. Box content

A. Tiller

B. Clutch handle

C. Gear rod

D. Depth skid

E. Support wheels and rear console

F. Lower handletube and upper handlebar

G. Blade guards

H. Throttle control

I. Middle- and outer tiller blades

J. Handle for turning the handlebar

2. Mount rear console, support wheels and depth skid

with the supplied cotter bolts and pins.

3. First, mount the lower handle tube. Use the

supplied mountings and bolts. Be careful not to

overtighten, so the bracket bend.

Then fit the upper handlebar. Use the supplied

assembly kit as shown. Do not overtight bolts.

4. Fit the plastic cover to the upper handlebar with the

supplied bolts and plastic plugs.

5. Mount clutch handle, throttle control and the handle

for turning the handlebar as shown in the picture.

6. Attach the gear rod as shown in the picture.

Tight the counter-nut, so the gear rod is properly

attached.

7. Mount the blade guards using the bolts and nuts

supplied. Note the blade guards has to go under

the body frame.

8. Attach the bumper using the bolts and nuts

supplied.

9. Mount the middle- and outer tiller blades using the

cotter bolts and pins.

Fill the motor with oil.

See changing the oil section for more details.

Clothing

When using the machine, wear close-fitting work

clothes, hard-wearing work gloves, ear defenders and

non-slip boots with steel toecaps.

Operating the tiller

Ensure the machine is placed on a level surface

with the support wheels lowered prior to start.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Texas Fusion 10TG in the language / languages: English, German, Danish as an attachment in your email.

The manual is 5,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Texas Fusion 10TG Manual

Product: