704022
15
Zoom out
Zoom in
Previous page
1/45
Next page
14
· System 4
Subwoofer controls
level control to 10 o'clock. While the AV receiver
is outputting its white noise setup signal, slowly
turn up the subwoofer level to the desired vol-
ume.

Phase
This switch determines the phase relationship be-
tween the subwoofer and the front/centre speakers.
If the subwoofer is positioned in the speaker setup
as indicated on p. 9 (grey area of drawing), set the
phase to 0°. With other setups, the 18 setting may
produce better results.

Frequency
Use this control to set the crossover fre-
quency between the subwoofer's bass signal
and the bass frequencies of the other speak-
ers. If you are using an AV receiver, set the re-
ceiver's crossover frequency to 100 Hz and turn
the subwoofer's frequency control to maximum
(hard right).
➑
Power
OFF means that the subwoofer is switched off; ON
means that it is switched on.
➒
Power LED
When the subwoofer's mains power switch ➑ is
off, the power LED is off. When the subwoofer's
mains power switch ➑is on, the power LED lights
up red or green, depending on the position of the
Power Function switch .
When the subwoofer is permanently active
(= Power Function ON), the power LED is green.
When the subwoofer is in standby mode (Power
Function AUTO), the power LED is red. After
the subwoofer is triggered into activity, the LED
changes to green. After the subwoofer switches
itself off after 20 minutes of inactivity, the LED is
red again. When the Power Function switch is
on OFF, the LED is red.
Voltage selector
This switch adapts the internal amplifier to the
local mains voltage. NEVER set this to any other
value than the standard local voltage value. In
Germany, the correct position is “220 – 240V.
{
Fuse
This is where the mains power fuse is located.

Power function
OFF means that the subwoofer is switched off; ON
means that it is switched on. AUTO means that the
subwoofer is operational but is only activated once
it receives an audio signal. In AUTO” mode, the sub-
woofer automatically switches to standby after 20
minutes of inactivity.

Line Input
Connect the AV receiver's Sub Out” to the subwoof-
er's “Line Input using a mono RCA cable (optionally
with an additional Y adapter).

Line Output
Here, you can connect a second subwoofer for added
bass or to compensate for resonant frequencies in
the room.
 Low Pass Full Range
With the switch on “LOW PASS”, the built-in con-
trols
for “Phase” and “Frequency are
activated.
With the switch on “FULL RANGE” (recommended
setting), these parameters are controlled by the
AV receiver.

Level
Use the “LEVEL control to adjust the subwoof-
er's volume. In the receiver's bass management
section, set the bass level to a high value, i.e.,
between 6 and 12 dB. Next, set the subwoofer's
What the icons mean
The lightning/arrow symbol
inside an equilateral triangle
informs the user about the
possibility of a dangerous, non-
isolated electrical current
inside the device housing,
indicating the risk of
electrical shock.
The exclamation mark within
the equilateral triangle, which
can be seen on the back of the
unit, indicates that there is
important operating and service
information for the user to read.
This product complies with the
following European Union
guidelines:
2004/108/EC and 2006/95/EC.
The “wastebin” symbol printed
on the type plates and amplier
labels of our products signies
that Lautsprecher Teufel ensures
the proper disposal of its sold
loudspeakers and subwoofers
according to Germany's
Electrical and Electronic
Equipment Act.
{
This product complies with DIN
EN 61140 (VDE 0140-1) and IEC
60417 of protection class II. It
only requires a two-pin round
plug (included) and not an
earthed plug. The plug has a
reinforced or double-shielded
casing to prevent electrical
shock.
Attention:
The separating equipment of
this equipment is the mains
plug, this separating equipment
must be usable without
difculties.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teufel Cinepaq 4400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teufel Cinepaq 4400 in the language / languages: English as an attachment in your email.

The manual is 2,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info