776629
8
Zoom out
Zoom in
Previous page
1/12
Next page
VCUP15 Vacuum Cleaner User Guide
Clearing a Blockage
If the cleaner loses suction and the dust in the dust cup is below
the MAX mark, this may be due to a blockage.
DO NOT operate the cleaner if the suction is impaired.
$Set the cleaner upright, switch off and unplug immediately.
$Empty the dust, check and clean all the filters.
$Disconnect the hose to see if debris has backed up.
$Examine the multi tool.
$Remove any blockage with a stick or broom handle.
If all the above seem clear, the lower hose may be blocked.
Pull the lower hose collar off the
inlet pipe. The fit is intentionally
tight.
Clear the blockage and replace
the hose.
If you notice that the brush speed is slow and/or there is a
loss of suction, this may be due to the brush getting clogged.
Prompt action will maintain cleaner performance and avoid any
potential problems of belt slippage.
Switch the cleaner off and unplug it from the mains.
Check that the
deflection plate
m o v e s f r e e l y.
Clean the brush
area and remove
all obstructions
before continuing
to use the cleaner.
IMPORTANT-Motor Thermostat
If the vacuum cleaner should overheat, the protective
thermostat will automatically turn the unit off.
If this occurs: Switch off and unplug. Check and clear any
blockage and clean/replace the filter.
Wait at least 45 minutes before attempting to reuse the
cleaner. After the cleaner has cooled down plug in and switch
on. The vacuum should now start.
DEFLECTION PLATE
Changing the Drive Belt
Sluggish speed and loss of suction may be caused by a worn or slack belt. A spare belt is provided.
DO NOT replace this components yourself unless you are confident that you can carry out this procedure satisfactorily.
Make sure the cleaner is switched off and unplugged from the mains before you start work. Protect the work surface if necessary.
You need a No2 Phillips screwdriver to carry out this procedure.
Stage 1. Remove the Cover Plate
Remove the Dust Cup.
Angle the cleaner fully back.
Turn the cleaner over and place it on a stout work bench
The cover plate is attached to the cleaner with six screws.
There are identified below (you can only access the centre
screw by first lifting up the deflection plate).
1: Remove all six screws and keep them safe
2: Ease the cover plate off to expose the brush and roller
1
2
Page 8
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tesco VCUP15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tesco VCUP15 in the language / languages: English as an attachment in your email.

The manual is 4.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info