770539
4
Zoom out
Zoom in
Previous page
1/8
Next page
Assembling Your Cleaner for Cleaning Floors
Page 4
1 2 3 4 5 6
Attaching the Handle and the Floor Head
There is a peg in the handle stem. Line up the peg in the stem with the hole in the cleaner housing and push it in. The peg will 1.
click into place securing the handle. You may need to push quite hard to insert the handle fully - it is an intentional tight t.
Line up the oor head with the nozzle in the body and push rmly. Now pull the oor head back slightly to check that it is 2.
securely attached.
Attaching the Cleaning Pad: Whenever you clean oors the cleaning pad must be rmly attached to the oor head. We recommend
you wash and and dry the cleaning pad before rst use to ensure that there are no lint particles adgering to the surface.
Around the edge of the cleaning pad there is a hook and loop strip. Place the cleaning pad on the oor with the strip facing 3.
up and align the cleaner over the pad.
Place the oor head on the pad and press lightly with your foot to attach the pad securely.4.
Attaching the Carpet Glider: Use the carpet glider only when you are refreshing carpeted surfaces.
Place the carpet glider on the oor as shown and align the cleaner over it..5.
Place the oor head on the glider and press lightly with your foot to attach the carpet glider securely.6.
Filling the Water Tank
7. Remove the water tank. Press the release button on the top of the tank and hinge the tank out.
8. Lift out the stopper on the tank. Fill the tank with fresh cold water or demineralised water (see Page 2) to a level just below the
top of the tank.
9. Push the stopper in rmly and replace the tank.
Filling the Solution Tank
Special detergent solutions are available. These solutions act with the steam to improve cleaning, refresh carpets and enhance
special nishes on solid oors. Always consult the oor manufacturer or a specialist professional before using detergent solutions
and always adhere strictly to the instructions on the detergent packaging concerning dilution levels etc. Always try the solution
on a test (hidden) area to check colour fastness and suitability before use.
10. Rotate the tank cap to the left to release it and then lift it o.
11. Press the “DETERGENT switch on the oor head to the OFF position and ll the tank with the correctly prepared solution to
just below the top of the tank. Replace the tank cap and tighten rmly. When lling the tank take care not to spill solution on
the oor. If you wish you can remove the tank (see Page 7) and ll it over a sink
Winding and releasing the mains cord
12. Wind the cord around the upper and lower cleats on the rear of the stem. The upper cleat is a quick
release type. Rotate the cleat to release the cord. When the cord is released return the cleat to the
vertical position. There is a slot in the top of the upper cleat. If you wish you can push the cable into
the slot to keep the power cord from getting in the way.
Your steam cleaner is now ready for use.
7 8 9
12
10 11
Close
Open
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tesco SM16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tesco SM16 in the language / languages: English as an attachment in your email.

The manual is 0.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info