742909

Tenda TEG3224P Manual

44
Zoom out
Zoom in
Previous page
1/177
Next page
User Guide
38
2) By default, after negotiation, LACP aggregation group 5 contains port 1 and port 3. Then, on the LACP
protocol interface, group ID 5 will be only displayed on port 1 and port 3.
3) Set Switch A’s system priority (on the LACP protocol interface) to a value which is smaller than 32768
so that switch A’s priority is higher than switch B’s. At the same time, set port 2’s LACP priority on switch
A to a value which is smaller than 32768 so that port 2’s priority is higher than port 1’s. Then view the
negotiation result of LACP aggregation group 5: Group ID on port 2 and port 4 displays 5, i.e. after
negotiation, LACP aggregation group 5 will contain port 2 and port 4.
4) Set Switch A’s system priority (on the LACP protocol interface) to a value which is greater than 32768
so that switch B’s priority is higher than switch A’s. At the same time, set port 1’s LACP priority on switch
B to a value which is smaller than 32768 so that port 1’s priority is higher than port 2’s. Then view the
negotiation result of LACP aggregation group 5: Group ID on port 1 and port 3 displays 5, i.e. after
negotiation, LACP aggregation group 5 will contain port 1 and port 3.
Port configuration considerations in link aggregation
To share egress/ingress traffic load, member ports in an aggregation group must be set to the same
configurations with respect to STP, port priorities, VLAN, port management, ARP attack defense, etc.
Consistent STP Configurations: Includes STP status, P2P port, edge port, port priority, path cost,
etc.
Consistent port priorities.
Consistent VLAN Configurations: Includes interface type, PVID, allowed VLAN and Untag/Tag
VLAN.
Consistent port priorities: Includes Jumbo frame, flow control and isolation settings.
Consistent ACL configurations: Includes Binding ACL lists
Consistent ARP attack defense: Includes ARP rate limit and ARP receiving rate settings.
If parameters on any port are changed in the aggregation group, configurations on other member ports
should be kept consistent.
For ports having joined in the aggregation group, following configurations are not allowed:
Adding static MAC address
Configuring MAC learning
Enabling IP filter
Configuring mirroring destination port
Enabling voice VLAN feature
Enabling 802.1X authentication
Below ports cannot join the aggregation group:
802.1x-enabled port(s)
ACL Binding port(s)
Mirroring destination port(s)
Ports on which MAC address filter is enabled
Ports on which IP address filter is enabled
Ports on which MAC address learning limit is set
4.3 VLAN Management
… 44 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tenda TEG3224P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tenda TEG3224P in the language / languages: English as an attachment in your email.

The manual is 8,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info