742866
61
Zoom out
Zoom in
Previous page
1/65
Next page
User Guide
57
Appendix 3 FAQs
This section provides solutions to problems that may occur during installation and operation of the device. Read the following if you
are running into problems. If your problem is not covered here, please go to www.tendacn.com to find a solution or email your
problems to: support@tenda.com.cn or support02@tenda.com.cn. We will be more than happy to help you out as soon as possible.
1. Q: I entered the device’s LAN IP address in the web browser but cannot access the utility. What should I do?
a.Check whether device is functioning correctly. The SYS LED should blink a few seconds after device is powered up. If it does
not light up, then some internal faults may have occurred.
b.Verify physical connectivity by checking whether a corresponding port’s link LED lights up. If not, try a different cable. Note that
an illuminated light does NOT ALWAYS indicate successful connectivity.
c. Run the "ping 192.168.0.1" command. If you get replies from 192.168.0.1, open your browser and verify that Proxy server is
disabled. In case that ping fails, press and hold the "RST" button on your device for 8 seconds to restore factory default settings,
and then run "ping192.168.0.1" again.
d. Contact our technical support for help if the problem still exists after you tried all the above.
2. Q: What should I do if I forget the login password to my device?
Reset your device by pressing the Reset button for over 8 seconds.
Note:
All settings will be deleted and restored to factory defaults once you pressed the Reset button.
3. Q: My computer shows an IP address conflict error after having connected to the device. What should I do?
a.Check if there are other DHCP servers present in your LAN. If exist, disable them immediately.
b.The default IP address of the device is 192.168.0.1; make sure this address is not used by another PC or device. In case that
two computers or devices share the same IP addresses, change either to a different address.
4. Q: I cannot access Internet and send/receive emails; what should I do?
This problem mainly happens to users who use the PPPoE or Dynamic IP Internet connection type. You need to change the MTU
size (1492 by default). In this case, go to “WAN Settings” to change the MTU value from default 1480 to 1450 or 1400, etc.
5. Q: How do I share resources on my computer with users on Internet through the device?
To let Internet users access internal servers on your LAN such as e-mail server, Web, FTP, via the device, use the "Virtual
Server" feature. To do so, follow steps below:
Step 1: Create your internal server, make sure the LAN users can access these servers and you need to know related service
ports, for example, port number for Web server is 80; FTP is 21; SMTP is 25 and POP3 is 110.
Step 2: Enter Port Forwarding (also called Port Range Forwarding on some products) screen from device web UI.
Step 3: Complete the Start Port (also called External/Ext Port on some products) and End Port (also known as Internal Port on
some products) fields, say, 80-80.
Step 4: Input the internal server’s IP address. For example, your Web server’s IP is 192.168. 0.10, simply input it.
Step 5: Select a proper protocol type: TCP, UDP, or Both depending on which protocol(s) your internal host is using.
Step 6: Click Enable and save your settings.
For your reference, we collected a list of some well-known service ports as follows:
Server
Protocol
Service Port
Web Server
TCP
80
FTP Server
TCP
21
Telnet
TCP
23
Net Meeting
TCP
1503, 1720
MSN Messenger
TCP/UDP
File Send:6891-6900(TCP) Voice:1863, 6901(TCP)
Voice:1863, 5190(UDP)
PPTP VPN
TCP
1723
Iphone5.0
TCP
22555
SMTP
TCP
25
POP3
TCP
110
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tenda FH307 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tenda FH307 in the language / languages: English as an attachment in your email.

The manual is 5,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info