742846
5
Zoom out
Zoom in
Previous page
1/157
Next page
AC1200 MU-MIMO Dual Band
Gigabit WiFi Router
AC10/AC10U
User Guide
AC1200 MU-MIMO Dual Band Gigabit WiFi Router · AC10 / AC10U
User Guide
Copyright Statement
© 2018 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and
product names mentioned herein are trademarks or registered trademarks of their respective holders. Copyright
of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda
Technology Co., Ltd. No part of this publication can be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language in any form or by any means without the prior written permission of
Shenzhen Tenda Technology Co., Ltd.
Disclaimer
Pictures, images and product specifications herein are for references only. To improve internal design,
operational function, and/or reliability, Tenda reserves the right to make changes to the products without
obligation to notify any person or organization of such revisions or changes. Tenda does not assume any liability
that may occur due to the use or application of the product described herein. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Preface
Thank you for choosing Tenda! Please read this user guide before you start with AC10/AC10U.
Conventions
The typographical elements that may be found in this document are defined as follows.
Item
Presentation
Example
Cascading menus
>
System > Live Users
Parameter and value
Bold
Set User Name to Tom.
Variable
Italic
Format: XX:XX:XX:XX:XX:XX
UI control
Bold
On the Policy page, click the OK button.
Message
The Success message appears.
The symbols that may be found in this document are defined as follows.
Meaning
This format is used to highlight information of importance or special interest.
Ignoring this type of note may result in ineffective configurations, loss of data or
damage to device.
This format is used to highlight a procedure that will save time or resources.
Picture of AC10U is used for guidance in network topologies in this user guide.
Acronyms and Abbreviations
Full Spelling
Internet Service Provider
Virtual Private Network
WiFi Protected Setup
Internet Protocol Television
Point-to-Point Protocol over Ethernet
Dynamic Host Configuration Protocol
Domain Name System
Access Point
Wireless Internet Service Provider
Point to Point Tunneling Protocol
Layer 2 Tunneling Protocol
Microsoft Point-to-Point Encryption
Point To Point Protocol
Dynamic Domain Name System
Demilitarized Zone
Virtual Local Area Network
Additional Information
For more information, search this product model on our website at http://www.tendacn.com.
Technical Support
If you need more help, contact us by any of the following means. We will be glad to assist you as soon as
possible.
Hotline
Global: (86) 755-27657180
United States: 1-800-570-5892
Canada: 1-888-998-8966
Hong Kong: 00852-81931998
Website
http://www.tendacn.com
http://www.tendaus.com
Email
support@tenda.com.cn
support.usa@tenda.com.cn
Contents
1 Introduction ....................................................................................................................................................... 1
1.1 Overview ...................................................................................................................................................... 1
1.2 Appearance .................................................................................................................................................. 2
2 Set up to access the internet ............................................................................................................................. 6
2.1 Setting the new router to access the internet ............................................................................................. 6
2.2 Replacing original router with AC10/AC10U .............................................................................................. 11
3 Web UI description .......................................................................................................................................... 18
3.1 Logging in to the web UI of the router ...................................................................................................... 18
3.2 Logging out of the web UI of the router .................................................................................................... 19
4 Internet Status ................................................................................................................................................. 20
4.1 Network status ........................................................................................................................................... 20
4.2 Online device/USB/WiFi extender ............................................................................................................. 21
4.3 WiFi information ........................................................................................................................................ 24
4.4 Other information ...................................................................................................................................... 26
5 Internet Settings .............................................................................................................................................. 27
5.1 Overview .................................................................................................................................................... 27
5.2 Setting up an internet connection with PPPoE .......................................................................................... 28
5.3 Setting up an internet connection with a dynamic IP address .................................................................. 30
5.4 Set up an internet connection with a static IP address.............................................................................. 31
6 WiFi Settings .................................................................................................................................................... 33
6.1 WiFi Name & Password .............................................................................................................................. 33
6.2 WiFi Schedule ............................................................................................................................................ 36
6.3 Wireless Repeating .................................................................................................................................... 38
6.4 Channel & Bandwidth ................................................................................................................................ 42
6.5 Transmit Power .......................................................................................................................................... 44
6.6 WPS ............................................................................................................................................................ 46
6.7 Beamforming+ ........................................................................................................................................... 51
6.8 AP Mode .................................................................................................................................................... 52
6.9 Anti-interference ........................................................................................................................................ 55
7 Guest Network ................................................................................................................................................. 56
7.1 Overview .................................................................................................................................................... 56
7.2 Setting guest network ................................................................................................................................ 57
8 Parental Control ............................................................................................................................................... 58
8.1 Overview .................................................................................................................................................... 58
8.2 Setting parental control rules .................................................................................................................... 59
9 VPN .................................................................................................................................................................. 63
9.1 PPTP Server ................................................................................................................................................ 63
9.2 Online PPTP Users ...................................................................................................................................... 70
9.3 PPTP/L2TP Client ........................................................................................................................................ 71
10 USB App ........................................................................................................................................................... 74
10.1 Overview .................................................................................................................................................. 74
10.2 Modifying role information ...................................................................................................................... 78
10.3 Accessing USB resources through FTP/Samba servers ............................................................................ 80
11 Advanced Settings ........................................................................................................................................... 86
11.1 Bandwidth Control ................................................................................................................................... 86
11.2 Tenda App ................................................................................................................................................ 87
11.3 Sleeping Mode ......................................................................................................................................... 91
11.4 LED Control .............................................................................................................................................. 92
11.5 Filter MAC Address .................................................................................................................................. 93
11.6 Firewall ..................................................................................................................................................... 97
11.7 IPTV .......................................................................................................................................................... 99
11.8 Static Route ............................................................................................................................................ 101
11.9 DDNS ...................................................................................................................................................... 105
11.10 Virtual Server ....................................................................................................................................... 110
11.11 DMZ Host ............................................................................................................................................. 115
11.12 UPnP .................................................................................................................................................... 116
12 System Settings .............................................................................................................................................. 118
12.1 LAN Settings ........................................................................................................................................... 118
12.2 DHCP Reservation .................................................................................................................................. 120
12.3 WAN Settings ......................................................................................................................................... 122
12.4 Time Settings ......................................................................................................................................... 124
12.5 Login Password ...................................................................................................................................... 125
12.6 Reboot and Reset ................................................................................................................................... 126
12.7 Firmware Upgrade ................................................................................................................................. 128
12.8 Backup/Restore ...................................................................................................................................... 130
12.9 Remote Management ............................................................................................................................ 131
12.10 System Status ....................................................................................................................................... 134
12.11 System Log ........................................................................................................................................... 137
12.12 Automatic Maintenance ...................................................................................................................... 138
Appendixes ............................................................................................................................................................ 141
A.1 Setting the IP address of your computer ................................................................................................. 141
A.2 FAQ .......................................................................................................................................................... 145
1
1 Introduction
1.1 Overview
AC10/AC10U is a high-performance router dedicated to fiber users. With the new 802.11ac wave2.0 standard and
four 6 dBi high-gain external antennas, AC10/AC10U offers simultaneous dual-band data rate of as high as 1167
Mbps. With Beamforming+ technology, AC10/AC10U features robust wall penetration capacity, making full use of
the FTTH’s advantage. The integration of technology MU-MIMO also makes AC10/AC10U support more devices at
one time, creating faster and better network for you.
Features
Supports 4 gigabit auto-negotiation ports.
Supports the MU-MIMO technology.
With 4 external omnidirectional antennas.
Supports to enable/disable the WiFi network of the router at a press of the WIFI button.
Supports WiFi Schedule to disable the WiFi network of the router at specified period.
Supports 12 V dc 1 A (for AC10), and 12 V dc 1.5 A (for AC10U) power output.
With a wireless data rate of as high as 1167 Mbps.
Supports Wireless Repeating and Bandwidth Control.
Supports migration of ISP user name and password for quick setup.
Supports remote management with Tenda WiFi App.
2
1.2 Appearance
1.2.1 Front panel
LED
indicator
LED indicator
name
Status
Description
SYS
System / USB
LED indicator
Solid on
The router is starting.
If the indicator is still solid on after your router
completes startup, it indicates that the system is
faulty.
Slowing blinking
The system is working properly.
Fast blinking twice
(AC10U only)
A portable USB device is connected to the USB port.
Fast blinking
(AC10U only)
Data is being transmitted over the USB port.
WAN
WAN LED
indicator
Solid on
The WAN port is connected properly.
Fast blinking
Data is being transmitted over the WAN port.
Off
The WAN port is disconnected or connected improperly.
LAN
LAN LED
indicator
Solid on
Port 1, 2 or 3 is connected properly.
Blinking twice
A device is connected to port 1, 2 or 3.
Off
None of ports 1, 2 and 3 is connected or connected
properly.
WiFi
WiFi / WPS
LED indicator
Solid on
At least the 2.4 GHz or 5 GHz WiFi network is enabled.
Fast blinking
Data is being transmitted wirelessly.
3
LED
indicator
LED indicator
name
Status
Description
Slow blinking
The router is performing WPS negotiation.
Off
The WiFi network is disabled.
1.2.2 Rear panel
AC10
AC10U
4
Port/Button
Description
WiFi
Used to enable/disable the WiFi network of the router.
RST/WPS
Used to start the WPS negotiation process of the router, or to reset the router.
WPS: Press the button of the router, and enable the WPS function of another
device within 2 minutes to establish a WPS connection.
Reset: When the SYS indicator blinks, hold the button down for about 8
seconds. The router is reset successfully when the SYS indicator lights solid on.
3
By default, it is a LAN port. But after the IPTV function of the router is enabled, it
functions only as an IPTV port used to connect to a set-top box.
1/2
They are LAN ports used to connect to devices such as computers and switches.
WAN
Used to connect this router to the internet.
POWER
Used to connect to the power adapter included with the package.
USB
(AC10U only)
Used to connect to a portable USB device.
1.2.3 Label on the bottom of the router
The bottom label shows the SSID, WiFi password and login IP address/domain name, pin code of the router. See
the following figures:
2
1
3
4
5
5
(1): It specifies the login IP address/domain name of the router. You can use this IP address/domain name to
access the web UI of the router.
(2): It specifies the serial number of the router. If the router is faulty, you need to provide this serial number for
repair.
(3): It specifies the default SSID of the routers WiFi network.
When you use AC10/AC10U for the first time, connect smart phone or other wireless devices to
this SSID to set up your router.
After the router is connected to the internet, if this SSID is not changed, wireless devices (such as
smart phones) connect to this SSID to access the internet. Otherwise, use the SSID and password
you set to access the internet.
(4): It specifies the default WiFi password of the router.
When you use AC10/AC10U for the first time, wireless devices connect the routers WiFi network
using this WiFi password to set up internet access.
After the router is connected to the internet, if this password is not changed, wireless devices
(such as smart phones) connect the routers WiFi network using this WiFi password. Otherwise,
use the SSID and password you set to access the internet.
(5): It specifies the pin code of the router. When you connect a device to the router by WPS, this pin code is
required.
1
2
3
4
5
6
2
Set up to access the internet
2.1 Setting the new router to access the internet
2.1.1 Setting up on phone
Step 1 Connect devices.
1. Power on the router using the power adapter included in the package.
2. Plug the Ethernet cable that has connected to the internet into the WAN port of the router.
3. Connect your smart phone to the WiFi network of the router using the WiFi name and password labeled
on the bottom of the router.
Step 2 Set up the router.
1. Start a web browser on the phone that has connected to the router, and visit tendawifi.com.
7
2. Tap Start.
3. The system detects your connection type automatically. Set the parameters based on your situation.
(PPPoE is used for instructions.)
ISP User Name: Enter the user name provided by your ISP.
ISP Password: Enter the password provided by your ISP.
4. Tap Next.
5. Set the WiFi name, WiFi password, and login password.
8
6. Tap Next.
--End
Wait a moment. Connected. Connect wireless devices to the WiFi network of the router again using the WiFi
name and password you set to access the internet. Wired devices can access the internet directly if they have
connected to port 1, 2 or 3.
For more functions, refer to relevant contents in this user guide.
2.1.2 Setting up on computer
Step 1 Connect devices.
1. Power on the router using the power adapter included in the package.
2. Plug the Ethernet cable that has connected to the internet into the WAN port of the router.
9
3. Connect your computer to port 1, 2 or 3 of the router using an Ethernet cable.
A desktop computer can connect to the WiFi network of the router only when it is installed with a
wireless adapter.
Step 2 Set up the router.
1. Start a web browser on the computer that has connected to the router. Enter tendawifi.com in the
address bar and press Enter.
2. Click Start.
10
3. The system detects your connection type automatically. Please set the relevant parameters based on
your actual situation. (PPPoE is used as an example for instructions here.)
- ISP User Name: Enter the user name provided by your ISP.
- ISP Password: Enter the password provided by your ISP.
4. Click Next.
5. Set the WiFi name (SSID), WiFi password and login password.
11
6. Click Next.
--End
Wait a moment. Connected. Connect wireless devices to the WiFi network of the router again using the WiFi
name and password you set to access the internet. Wired devices can access the internet directly if they have
connected to port 1, 2 or 3.
For more functions of the router, click More.
2.2 Replacing original router with AC10/AC10U
This setup method applies to users who use new routers to replace their original routers with PPPoE user names
and passwords, which can migrate user names and passwords from original routers to new routers quickly.
2.2.1 Setting up on phone
Step 1 Migrate your PPPoE user name and password from your original router.
1. Power on your original and new routers.
2. Connect the WAN port of the original router to port 1, 2 or 3 of the new router using an Ethernet cable.
When the LAN and WAN indicators of the new router light solid on for 3 seconds after blinking fast, your PPPoE
12
user name and password are migrated successfully.
3. Remove the original router.
Step 2 Connect devices.
1. After successful migration, plug the Ethernet cable that has connected to the internet into the WAN port
of the new router.
2. Connect your wireless device such as a smart phone to the WiFi network of the new router using the
WiFi name and password on the bottom label of the router.
Step 3 Set up the router.
1. Start a web browser on the phone that has connected to the router, and visit tendawifi.com.
2. Tap Start.
13
3. The system populates your PPPoE user name and password automatically. Tap Next.
4. Set the WiFi name (SSID), WiFi password and login password.
14
5. Tap Next.
--End
Wait a moment. Connected. Connect wireless devices to the WiFi network of the router again using the WiFi
name and password you set to access the internet. Wired devices can access the internet directly if they have
connected to port 1, 2 or 3.
For more functions, refer to relevant contents in this user guide.
2.2.2 Setting up on computer
Step 1 Migrate your PPPoE user name and password from your original router.
1. Power on your original and new routers.
2. Connect the WAN port of the original router to port 1, 2 or 3 of the new router using an Ethernet cable.
15
When the LAN and WAN indicators of the new router light solid on for 3 seconds after blinking fast, your PPPoE
user name and password are migrated successfully.
3. Remove the original router.
Step 2 Connect devices.
1. After successful immigration, connect WAN port of the new router to an Ethernet cable that has
connected to the internet.
2. Connect your computer to port 1, 2 or 3 of the new router using an Ethernet cable.
A desktop computer can connect to the WiFi network of the router only when it is installed with a
wireless adapter
Step 3 Set up the router.
1. Start a web browser on the computer that has connected to the router. Enter tendawifi.com in the
address bar and press Enter.
16
2. Click Start.
3. The system populates your PPPoE user name and password automatically. Click Next.
4. Set the WiFi name (SSID), WiFi password and login password.
17
5. Click Next.
--End
Wait a moment. Connected. Connect wireless devices to the WiFi network of the router again using the WiFi
name and password you set to access the internet. Wired devices can access the internet directly if they have
connected to port 1, 2 or 3.
If you want to configure more functions of the router, click More.
18
3 Web UI description
3.1 Logging in to the web UI of the router
This section describes how to log in to the web UI of the router to manage your router. For the first time to set up
your router, refer to Chapter 2 Set up to access the internet for instructions.
1. Start a web browser on the computer connected to your router. Enter tendawifi.com in the address bar,
and press Enter.
2. Enter the login password of your router, and click Login.
--End
If the figure above does not appear, set the Local Area Connection of your computer to Obtain an IP
address automatically and Obtain DNS server address automatically. For detailed setting steps, refer to
A.1 Setting the IP address of your computer in appendixes. Then try logging in again.
Log in to the web UI of the router successfully. See the following figure:
19
3.2 Logging out of the web UI of the router
If you log in to the web UI of the router and perform no operation within 5 minutes, the router logs you out. In
addition, click Exit on the upper right corner of the web UI can log out as well.
20
4 Internet Status
The Internet Status page allows you to view the network status of the router, online devices, WiFi information
and other status information.
4.1 Network status
This page shows the current network status of the router.
When the internet icon is displayed, the router is connected to the internet successfully and devices can
access the internet through the router.
Parameter description:
Parameter
Description
Current Speed
The upload and download rates of the WAN port.
WAN IP Address
The IP address of the WAN port.
Firmware Version
It specifies the current firmware version of the router. After upgrading the firmware
version of the router, you can view the current firmware version here to check whether
the upgrade is successful.
21
When Connection failed is displayed, click Connection failed to enter the Internet Settings page, and perform
according to the onscreen instructions to solve the issue.
4.2 Online device/USB/WiFi extender
The right part of the Internet Status page shows the number of portable USB device inserted into the router,
online devices, and gets you to know more about WiFi extender.
4.2.1 Online device
Click Online to find detailed information about online devices. See the following figure:
22
Add to Blacklist
Click Add to Blacklist to add unknown devices to the blacklist. Devices in the blacklist cannot access the internet
through the router.
Remove from Blacklist
To remove a device from the blacklist, click Online on the Internet Status page. Then click Blacklist on the
Manage Device page and locate the corresponding device. Click Remove.
Devices removed from the blacklist can access the internet through the router.
4.2.2 USB
Click USB to view detailed information about the USB devices connected to the router.
23
If a USB device is connected to your router, the USB page appears as follows: (USB Kingston DT 101 G2 is used as
an example here)
To disconnect your USB, click Unmount.
24
After you disconnect your USB device, the USB page appears as follows:
For detailed information about USB function of your router (Only AC10U supports USB function), click USB App
Center to access the USB App page.
4.3 WiFi information
The upper-right part of the Internet Status page displays the WiFi names (SSIDs) of 2.4 GHz and 5 GHz WiFi
networks. After the router accesses the internet, you can connect wireless devices to 2.4 GHz and 5 GHz WiFi
network SSIDs to access the internet.
25
To change WiFi names or passwords of 2.4/5 GHz WiFi network, click on the Internet Status page, and
configure the parameters on the WiFi Settings page. See the figure below:
Set your WiFi names and passwords. If WiFi password is not set before, you need to select the encryption mode
before setting the WiFi password. After configuring the parameters, click Save. Refer to Chapter 6 WiFi Name
and Password for detailed instructions.
26
Only devices supporting 5 GHz signal can scan and connect to the 5 GHz WiFi network of the router. You
are recommended to encrypt your wireless network for higher network security.
4.4 Other information
Click the router icon on Internet Status page. You can know more about the basic information, WAN port
status, LAN port status and WiFi status of the router. See Chapter 12 System Settings for detailed parameter
information.
27
5 Internet Settings
5.1 Overview
This page allows you to set internet parameters. Generally, the router detects your internet connection type
automatically when you use the router for the first time or after you reset the router. You are recommended to
select the detected connection type and follow the onscreen instructions to finish internet setup.
The following table may help you understand your internet connection type. If you are still uncertain about your
internet connection type, consult your ISP.
Connection
Type
Description
PPPoE
ISP user name and password are provided by your ISP.
Dynamic IP
Address
Your ISP does not provide ISP user name, password or other information about IP address.
Static IP
Address
Your ISP provides IP address, subnet mask, default gateway, DNS server(s).
To access the configuration page, click Internet Settings. PPPoE is used as an example here.
28
Parameter description:
Parameter
Description
WAN Port
It specifies the current status of the WAN port of the router, including Ethernet cable
connected and Ethernet cable disconnected.
Connection Type
It specifies how the router is connected to the internet. This router supports three
connection types: PPPoE, dynamic IP address, and static IP address. Please select your
connection type according to your actual situation.
ISP User Name
Enter the user name provided by your ISP.
ISP Password
Enter the password provided by your ISP.
DNS Settings
It specifies how the router obtains DNS information. This item is only needed when you
choose to connect the router to the internet by PPPoE or dynamic IP address.
- Automatic: The router obtains DNS information from upstream device automatically.
- Manual: You need to enter correct DNS information manually.
IP Address
The information is required only when you choose to connect the router to internet by
static IP address. Enter the IP address and other information provided by your ISP
manually.
Subnet Mask
Default Gateway
Primary DNS
Server
Secondary DNS
Server
Connection Status
It specifies whether the router is connected to the internet. If the Connected. You can
access the internet now.message appears, the router is connected to the internet
successfully and you can access the internet through your router. Otherwise, the router
fails to connect to the internet. Please perform according to the onscreen instructions.
Connection
Duration
It specifies how long the router is connected to the internet successfully this time.
5.2 Setting up an internet connection with PPPoE
Procedures:
1. Click Internet Settings.
2. Connection Type: Select PPPoE from the drop-down list box.
3. ISP User Name: Enter the user name provided by your ISP.
4. ISP Password: Enter the password provided by your ISP.
5. Click Connect.
29
--End
Verification
Assume that the ISP user name is chenhao, and password is 1234567. If the “Connected. You can access the
internet now.” message appears, you can access the internet through the router in a wired or wireless manner.
30
5.3 Setting up an internet connection with a
dynamic IP address
Procedures:
1. Click Internet Settings.
2. Connection Type: Select Dynamic IP.
3. Click Connect.
--End
Verification
If the Connected. You can access the internet now. message appears, you can access the internet through the
router in a wired or wireless manner.
31
5.4 Set up an internet connection with a static IP
address
Procedures:
1. Click Internet Settings.
2. Connection Type: Click Static IP Address.
3. IP Address, Subnet Mask, Default Gateway and Primary/Secondary DNS Server: Enter the relevant
information provided by your ISP. Assume that the IP address in this example is 192.168.20.1, subnet
mask 255.255.255.0, default gateway and primary DNS server 192.168.20.100.
4. Click Connect.
--End
Verification
If the Connected. You can access the internet now. message appears, you can access the internet through the
router in a wired or wireless manner.
32
33
6 WiFi Settings
This module includes the following functions: WiFi Name & Password, WiFi Schedule, Wireless Repeating,
Channel & Bandwidth, Transmit Power, WPS, Beamforming+, AP Mode, and Anti-interference.
6.1 WiFi Name & Password
6.1.1 Overview
This router supports 2.4 GHz and 5 GHz WiFi signals. Features of these two signals are listed as follows:
2.4 GHz signal has longer wireless transmission distance than 5 GHz signal.
2.4 GHz signal has better wall penetration capacity than 5 GHz signal.
5 GHz signal has higher wireless transmission speed than 2.4 GHz signal.
Comparing with 5 GHz, 2.4 GHz signal is more crowded, interrupted, but less stable.
You can set the WiFi names, encryption modes, and WiFi passwords for two WiFi networks on the WiFi Name &
Password page. To access the configuration page, click WiFi Settings > WiFi Name & Password.
Parameter description:
Parameter
Description
2.4 GHz/ 5 GHz
Network
Used to enable/disable the 2.4 GHz/5 GHz WiFi network of your router.
WiFi Name
It specifies the name of 2.4 GHz/5 GHz WiFi network. You can change it if needed. After the
router connects to the internet, wireless devices can surf the internet by connecting to the
34
WiFi name.
Encryption
Mode
It specifies the encryption modes supported by the router, including:
- None: It indicates that the wireless network is not encrypted so that any wireless devices
can connect to it. This option is not recommended as it leads to low network security.
- WPA-PSK: It indicates that the WiFi network uses WPA-PSK/AES as its authentication
method.
- WPA2-PSK: It indicates that the WiFi network uses WPA2-PSK/AES as its authentication
method.
- WPA/WPA2-PSK (Recommended): It indicates that the WiFi network uses the mixed
authentication method of WPA-PSK/AES and WPA2-PSK/AES as its authentication
method.
WiFi Password
It specifies the WiFi password which is required when your wireless devices try connecting to
the WiFi network.
Hide
It specifies whether to prevent the WiFi name from being detected by wireless devices.
If the box beside Hide is checked, the router does not broadcast the WiFi signal. The WiFi
name does not appear in the devices’ lists of available networks, either. When wireless
devices connect to the WiFi network, users should manually enter the WiFi name for
connection.
6.1.2 Changing WiFi name & WiFi password
Assume to change the 2.4 GHz WiFi name to Tenda_2.4G, WiFi password to 12345678; 5 GHz WiFi name to
Tenda_5G, WiFi password to 87654321.
Procedures:
Step 1 Click WiFi Settings > WiFi Name & Password.
Step 2 Change 2.4 GHz WiFi network information.
1. WiFi Name: Set Tenda_2.4G as the WiFi Name.
2. Encryption Mode: Keep the default setting, which is WPA/WPA2-PSK in this example. You can change it
if needed.
3. WiFi Password: Set 12345678 as the WiFi password.
Step 3 Change 5 GHz WiFi network information.
1. WiFi Name: Set Tenda_5G as the WiFi Name.
2. Encryption Mode: Keep the default setting, which is WPA/WPA2-PSK in this example. You can change it
if needed.
3. WiFi Password: Set 87654321 as the WiFi password.
Step 4 Click Save.
35
--End
Verification
Wait a moment for the modification to complete successfully. You can find the WiFi names have been changed on
the Internet Status page.
36
6.2 WiFi Schedule
6.2.1 Overview
This WiFi Schedule function allows you to disable the WiFi network of the router at specified period. By default,
this function is disabled.
To access the configuration page, click WiFi Settings > WiFi Schedule.
The following figure appears when the WiFi Schedule function is enabled:
Parameter description:
Parameter
Description
WiFi Schedule
Used to enable/disable the WiFi Schedule function.
Turn Off
During
It specifies the period when the WiFi network is disabled. In that period, wireless devices
cannot search the router’s WiFi networks, but out of that period they can search and
connect to the WiFi networks.
In
It allows you to customize your WiFi schedule. See the following:
37
-
Every Day: The router disables its WiFi networks at the specified time you set every day.
-
Specified Day: The router disables its WiFi networks at the specified time you set on
specified days.
6.2.2 Example
Scenario
Michael bought an AC10/AC10U for network coverage. For a healthier sleeping environment, he wants to disable
the WiFi networks every day during 23:00 to 7:00.
Procedures:
1. Click WiFi Settings > WiFi Schedule.
2. Set the WiFi schedule button to .
3. Turn Off During: Set the period as needed, which is 23:00~07:00 in this example.
4. In: Select the schedule type as needed, which is Every Day in this example.
5. Click Save.
--End
Verification
The WiFi networks are disabled from 23:00 to 07:00 every day.
38
6.3 Wireless Repeating
6.3.1 Overview
The Wireless Repeating function enables the router to expand WiFi coverage by connecting to the WiFi network
of an upstream router. This router supports two wireless repeating modes: WISP and Client+AP.
If repeating the WiFi hotspot provided by ISP, you are recommended to select WISP. Otherwise, select
WISP or Client+AP.
To access the configuration page, click WiFi Settings > Wireless Repeating. By default, the Wireless Repeating
function is disabled.
Set the wireless repeating button to . Then the following figure appears:
If wireless repeating is enabled, the Sleeping Mode, IPTV Function, Guest Network, WPS, Tenda App, and WiFi
Schedule functions become unavailable. You can find their icons disappear on the WiFi Settings page.
Parameter description:
Parameter
Description
Wireless Repeating
Used to enable/disable the Wireless Repeating function.
39
Repeating Mode
It specifies how the router repeats the upstream WiFi network.
-
WISP: The router repeats WiFi hotspot provided by ISP or ordinary WiFi network.
-
Client+AP: The router repeats ordinary WiFi network.
Upstream WiFi
Name
It specifies the name of the WiFi network you decide to repeat. You can select it from
the drop-down list box.
Upstream WiFi
Password
It specifies the password of the WiFi network you decide to repeat. This parameter
appears after you select the upstream WiFi name.
6.3.2 Example
Scenario
Michael bought a wireless router for network after having broadband service. The router is placed in the living
room. WiFi signals are strong in the living room and master bedroom, but too poor in the other bedrooms and
restrooms to access the internet. Now he wants to expand the WiFi coverage, ensuring devices to access the
internet everywhere.
Solution
Michael can buy an AC10/AC10U, and set the wireless repeating function on it to expand the WiFi network
coverage of the original router. Thus, devices in dead zones can access the internet through the WiFi signal of
AC10/AC10U. See the following figure:
40
Procedures:
1. Click WiFi Settings > Wireless Repeating.
2. Set the wireless repeating button from to .
3. Select WISP or Client+AP.
4. Upstream WiFi Name: Select the WiFi name of the original router from the drop-down list box, which is
majianwei in this example.
5. Upstream WiFi Password: Enter the password of the WiFi network of the original router, which is
12345678 in this example. (If the wireless network of the upstream router is unencrypted, leave this box
blank.)
6. Click Save.
7. Click OK.
--End
Verification
After the message Connected. You can access the internet now. appears on the Internet Settings page and the
Internet Status page appears as the second figure, devices can access the internet through the WiFi network of
AC10/AC10U.
41
42
-
If the connection type provided by the upstream router is dynamic IP address, the new router
obtains connection information from the upstream router automatically. If the connection type is
static IP address, you need to set the connection information manually.
-
In mode WISP, if the LAN IP address of the new router is in the same network segment as that of the
upstream router, an IP conflict occurs. In this case, the new router replaces its LAN IP address with
an IP address which belongs to another network segment. Then log in to the web UI of the new
router using tendawifi.com.
-
In Client+AP mode, the LAN IP address of A10/AC10U changes and you can view the new IP address
from the DHCP client list of the upstream router.
6.4 Channel & Bandwidth
6.4.1 Overview
This module allows you to change network mode, WiFi channel, and WiFi bandwidth of either 2.4 GHz or 5 GHz
WiFi network. Please retain the default channel and bandwidth settings if you set without professional guidance.
To access the configuration page, click WiFi Settings > Channel & Bandwidth.
Parameter description:
Parameter
Description
Network
It specifies various protocols adopted for wireless transmission. You are recommended to keep
the default settings. For 2.4 GHz networks, 11b/g mixed, 11b/g/n mixed, and 11n protocols are
43
Parameter
Description
Mode
available. For 5 GHz networks, the 11ac and 11a/n/ac protocols mixed are available.
-
11b/g mixed: It indicates that devices compliant with 802.11b or 802.11g protocol can connect
to the router.
-
11b/g/n mixed: It indicates that all devices working at 2.4 GHz and compliant with 802.11b,
802.11g, or 802.11n protocol can connect to the router.
-
11n: It indicates that devices working at 2.4 GHz and compliant with 802.11n can connect to
the router.
-
11ac: It indicates that devices complaint with 802.11ac protocol can connect to the router.
-
11a/n/ac mixed: It indicates that devices working at 5 GHz and compliant with 802.11a,
802.11n or 802.11ac protocol can connect to the router.
WiFi
Channel
It specifies the operating channel of a WiFi network.
By default, the WiFi channel is Auto, which indicates that the router selects a proper channel
based on the utilization rate it detected. But you can change it as required. A channel different
from nearby channels and with less interference are recommended to use because of better
wireless transmission efficiency. You can use a third-party tool to identify the channels different
from nearby channels and with less interference.
WiFi
Bandwidth
It specifies the bandwidth of the WiFi channel of a WiFi network. Change the default settings only
when necessary.
-
20: It indicates that the channel bandwidth of a router is to 20 MHz.
-
40: It indicates that the channel bandwidth of a router is 40 MHz.
-
20/40: It specifies that a router can switch its channel bandwidth between 20 MHz and 40 MHz
based on the ambient environment. This option is available only at 2.4 GHz.80: It indicates that
the channel bandwidth of a router is 80 MHz. This option is available only at 5 GHz.20/40/80: It
specifies that a router can switch its channel bandwidth among 20 MHz, 40 MHz, and 80 MHz
based on the ambient environment. This option is available only at 5 GHz.
6.4.2 Changing WiFi channel
Assume that the channel at 2.4 GHz WiFi network is required to change to channel 11, and 5 GHz WiFi network to
channel 157.
Procedures:
1. Click WiFi Settings > Channel & Bandwidth.
2. Change the channel of 2.4 GHz WiFi network to Channel 11.
3. Change the channel of 5 GHz WiFi network to Channel 157. (If there is no special requirement, retain
the other default settings.)
4. Click Save.
44
--End
6.5 Transmit Power
This router supports three WiFi signal strength modes: Low, Medium, and High. By default, 2.4 GHz and 5 GHz
WiFi signal is in the High mode. You can adjust the WiFi coverage and wall penetration capacity of the routers
WiFi network through changing its WiFi signal strength mode.
To access the configuration page, click WiFi Settings > Transmit Power.
45
Descriptions about WiFi signal strength modes:
Low: WiFi transmit power in this mode is relatively weak, suitable for small-area or barrier-free WiFi
coverage environment.
Medium: WiFi transmit power in this mode is relatively strong, suitable for medium-area WiFi coverage
environment or environment with few barriers.
High: WiFi transmit power in this mode is strong, suitable for large-area WiFi coverage environment or
environment with many barriers.
If WiFi network experience is excellent in Low mode, you are recommended to set your router in this mode.
If you want to improve your network experience in some areas with poor WiFi signal, you are recommended to
have a Tenda WiFi extender to get your WiFi coverage wider. Click Details to know more about the recommended
Tenda WiFi extender. For instructions about how to extend WiFi coverage using WiFi extender, refer to the
installation guide or user guide of your WiFi extender.
46
6.6 WPS
6.6.1 Overview
The WPS function enables wireless devices such as smart phones to connect to WiFi networks of the router
easily.
To access the configuration page, click WiFi Settings > WPS. Then follow the onscreen instructions to set.
47
6.6.2 Connect devices to WiFi network using WPS
-
Smart phones can connect to the WiFi network of the router through WPS only when they support
WPS function.
-
Desktops or laptops can connect to the WiFi network of the router through WPS only when they are
installed with wireless adapters. For detailed information, please refer to the user guide of relevant
wireless adapter.
Method 1: Setting through the web UI of the router
1. Click WiFi Settings > WPS.
2. Click Click Here. Then the router’s WiFi LED indicator on the front panel is blinking slowly.
3. Set WPS on a smart phone or computer installed with wireless network adapter within 2 minutes.
--End
Smart phones or computers are connected to the WiFi network of the router successfully after a while.
Method 2: Setting via the WPS button on the router
1. Press the WPS button on the router.
2. Set WPS on a smart phone or computer installed with wireless adapter within two minutes.
--End
The smart phone or computer is connected to the WiFi network of the router successfully after a while.
Method 3: Setting through pin code of the router
WPS connection using pin code is generally applied on computer with wireless adapter. Please refer to
relevant adapters user guide for detailed instructions.
48
1. Record the router’s pin code labeled on the bottom of the router.
2. Enter the pin code on the device for connection.
--End
The device is connected to the routers WiFi network successfully after a while.
6.6.3 Example
Scenario
Michael bought an AC10/AC10U for network and he has set the WiFi password. He hopes to connect devices to
the routers WiFi network without entering WiFi password. Assume that the WiFi name of his router is
Tenda_XXXXXX.
The WPS function can address this requirement.
Procedures:
Step 1 Set up the router.
1. Click WiFi Settings > WPS > Click Here.
49
Step 2 Set WPS on a smart phone. Smart phone Redmi Note 4X is used as an example here.
1. Click Settings on the phone’s homepage.
2. Then click WLAN > Advanced Settings > Connect WPS.
50
3. The smart phone is performing WPS negotiation with the router.
--End
Wait a moment for the negotiation to complete. Then the smart phone connects to the routers WiFi network
successfully.
51
Verification
The smart phone accesses the internet through the routers WiFi network successfully.
6.7 Beamforming+
6.7.1 Overview
As a wireless signal optimization technology, the location-oriented Beamforming could transmit wireless
signals to wireless devices precisely, offering users with better internet connection, such as higher
download speed or playback of HD videos. Wireless routers broadcast signals to all directions in
transmission if they do not support Beamforming+ function.
Wireless routers supporting Beamforming+ could transmit wireless signals toward the location of
connected devices, improving users’ internet experiences.
The following figure shows the wireless transmission when Beamforming+ is disabled.
52
The following figure shows the wireless transmission when Beamforming+ is enabled.
6.7.2 Setting Beamforming+
To access the configuration page, click WiFi Settings > Beamforming+. By default, Beamforming+ function is
enabled. You are recommended to retain the default settings.
6.8 AP Mode
6.8.1 Overview
In AP mode, the router implements the functions of wireless access point (AP), and WAN port of the router
functions as a LAN port. Usually, in AP mode, when the router connects to the upstream router using an Ethernet
cable, the router extends the wireless network coverage of the upstream router, or transforms the wired signal to
wireless one.
To access the configuration page, click WiFi Settings > AP Mode. By default, AP mode is disabled.
53
6.8.2 Enabling AP mode
1. Click WiFi Settings > AP Mode.
2. Set the AP mode button to .
3. Click Save.
--End
-
If AP mode is enabled, Internet Settings, VPN, Parental Control, Bandwidth Control, and Virtual
Server functions become unavailable.
-
The LAN IP address of the router will be changed since AP mode is enabled. Please log in to the
routers web UI by domain name tendadwifi.com, or look for the new LAN IP address from the
client list of the upstream router, and log in to the router through the new IP address.
6.8.3 Example
Scenario
Michael could access the internet through his optical modem only in a wired manner. Now he wants to access the
internet by WiFi network.
54
Solution
He is recommended to purchase an AC10 or AC10U and enable its AP mode. After setting up the router
successfully, his wireless devices like smart phones could access the internet through WiFi network of the router.
Connect a LAN port of the optical modem to any port of the router using an Ethernet cable. Then connect your
computer to the router using an Ethernet cable and your smart phones to the routers WiFi network. See the
following figure:
Procedures:
1. Click WiFi Settings > AP Mode.
2. Set the AP mode button to .
3. Click Save.
4. Click Ok in the following window that appears:
55
--End
Verification
Wired devices like computers could access the internet successfully if they connect to the router using Ethernet
cables, and wireless devices likes smart phones are also available to the internet if they connect the routers WiFi
network.
6.9 Anti-interference
This router supports the Anti-interference function. When having bad internet experience, you are allowed to
modify the Anti-interference settings.
To access the configuration page, click WiFi Settings > Anti-interference. By default, this function is in Auto
status.
When you choose Auto, the router will adjust receiving sensitivity automatically based on the current
interference. Please keep Auto if you do not have any special requirement.
When you choose Enable, the router has better anti-interference ability but smaller WiFi coverage.
When you choose Disable, the router has wider WiFi coverage. But if the interference is strong is your
environment, you are recommended to choose Auto or Enable.
56
7 Guest Network
7.1 Overview
This module makes you able to enable/disable the Guest Network function and change guest network’s WiFi
name and password.
Devices connected to the guest network can access to the internet and communicate with each other, but cannot
access the routers web UI or the master network. This function not only enables guests to access the internet
but also ensures the security of the master network.
To access the configuration page, click Guest Network. By default, the Guest Network function is disabled.
Parameter description:
Parameter
Description
Guest Network
Used to enable the Guest Network function. By default, this function is disabled.
2.4 GHz/ 5 GHz
WiFi Name
It specifies the WiFi name of the router’s guest network. By default, Tenda_VIP is for 2.4
GHz WiFi network and Tenda_VIP_5G for 5 GHz WiFi network.
You can change the SSIDs if required. To distinguish the guest network from the master
network, you are recommended not to set the same name for these two networks.
Guest Network
Password
It specifies the password for the router’s two guest networks. Please set the password
according to your requirements.
57
Parameter
Description
Validity
It specifies the validity of the guest networks. The Guest Network function will be disabled
automatically out of the specified time so wireless devices will not search it. Please set the
validity as needed.
Shared
Bandwidth for
Guests
It specifies the downloading speed of guest network devices, with a unit Mbps. By default,
the speed is not limited. You can set it as needed.
7.2 Setting guest network
1. Click Guest Network.
2. Set the Guest Network button to .
3. 2.4 GHz WiFi Name: Change the WiFi name, such as to Michael.
4. 5 GHz WiFi Name: Change the WiFi name, such as to Michael_5G.
5. Guest Network Password: Set the password for guest networks, such as to 987654321.
6. Validity: Click the drop-down box, and choose 4 hours.
7. Shared Bandwidth for Guests: Click the drop-down box, and choose 2.
8. Click Save.
--End
After configuration, wireless devices such as smart phones, connected to Michael or Michael_5G share a
downloading speed up to 2 Mbps, and can access the internet consecutively for 4 hours.
58
8 Parental Control
8.1 Overview
This module enables you to set the internet accessibility of devices in the routers LAN network, including
specified time for surfing the internet, websites allowed or banned to visit.
To access the configuration page, click Parental Control. The Parental Control page shows devices which are
connected to the router currently.
Parameter description:
Parameter
Description
Device Name
It specifies names of the devices connected to the router.
MAC Address
It specifies MAC addresses of the devices connected to the router.
Uptime
It specifies the time that has elapsed since the device is connected to the router currently.
Operation
Click to set limits for devices to access the internet through the router.
+New
Click +New to add devices and set limits for them.
59
8.2 Setting parental control rules
8.2.1 Scenario 1: The device has been connected to the router
1. Click Parental Control.
2. In device list, locate the device you want to set rules on and click .
3. Set valid time for internet connection, and websites banned or allowed to visit.
4. Click Save.
--End
60
8.2.2 Scenario 2: The device has not been connected to the
router
1. Click Parental Control.
2. Click +New.
3. Set device name, MAC address, time limit to internet access and limit to website access as required.
4. Click Save.
--End
61
Parameter description:
Parameter
Description
Device Name
It specifies the name of the device you want to apply the rule to.
MAC Address
It specifies the MAC address of the device you want to apply the rule to.
Internet Accessible
At
It specifies the specific time for the device to access the internet through the router.
In
It specifies dates for the device to access the internet through the router.
Website Access
Limit
Used to enable/disable the website access limit function. By default, this function is
enabled.
Access Control
Mode
It specifies modes for website access limit in a parental control rule.
-
Blacklist: The device under the rule is not allowed to visit the website(s) below.
-
Whitelist: The device under the rule is only allowed to visit the website(s) below.
Blocked/Unblocked
Websites
It specifies the websites that the device under the rule is banned/allowed to visit during
Internet Accessible At.
8.2.3 Example
Scenario
Michael bought an AC10/AC10U for network. His children always surf the internet on smart phones through the
router. For the good of his children’ learning, he intends to allow his children to access Google during 8:00 to
22:00 from Monday to Friday.
Solution
The Parental Control function of AC10/AC10U could fulfill his requirements.
Procedures:
1. Click Parental Control.
2. In device list, locate the device you want to set a rule on and click .
62
3. Internet Accessible At: Set time limit for the device to access the internet, which is 08:00~20:00 in this
example.
4. In: Select Specified Day and then Monday to Friday.
5. Access Control Mode: Click Whitelist.
6. Unblocked Websites: Enter the website accessible for the device, which is google in this example.
7. Click Save.
--End
Verification
Google is only accessible for the device under the rule during 8:00-20:00 on weekdays.
63
9 VPN
The VPN module includes the following functions: PPIP Server, Online PPTP Users, and PPTP/L2TP Client.
VPN (Virtual Private Network) is a dedicated network across the shared or public network (usually the internet).
However, since this dedicated network does not have physical lines but only exists logically, it is called the virtual
private network. The VPN technology allows employees at a branch of an enterprise and employees at the
headquarters to exchange resources conveniently without exposing these resources to other internet users.
9.1 PPTP Server
9.1.1 Overview
The PPIP Server page allows you to set the router as PPIP server.
PPTP server allows the specified VPN users to dial in. For example, you can allows staffs on business trip to access
the headquarters resources through VPN dialing up on a router whose PPTV server function is enabled.
To access the configuration page, click VPN > PPTP Server.
After enabling the PPIP Server function, the figure below appears:
64
Parameter description:
Parameter
Description
PPTP Server
Used to enable/disable the PPTP server function. If the function is enabled, the router
functions as a PPTP server.
IP Address
Pool
It specifies the range of IP addresses that the PPTP server can assign to users.
MPPE
Encryption
Used to enable/disable the MPPE encryption function.
User Name
Set user name and password that is allowed to dial in the PPTP server. This name and
password are needed when a device connects to the PPTP server.
Password
Connection
Status
It specifies the status of a VPN connection.
Operation
The following operations can be performed on the PPTP user rules:
-
+New: It is used to add PPTP users. Users can access the PPTP server successfully after you
have added them.
-
: It is used to disable PPTP users to access the PPTP server.
-
: It is used to enable PPTP users to access the PPTP server again if they were disabled
before.
-
: It is used to delete PPTP users.
9.1.2 Example
Scenario
Michael bought an AC10/AC10U for network. And he needs to access the resources of his FTP server at home.
65
Solution
The PPTP server function of AC10/AC10U can address this requirement. Set PPTP Server function on the router.
He can access the resources on the computers FTP server by VPN dialing up on business trip.
Assume that the IP address of the FTP server is 192.168.0.104, and the WAN IP address of the router is
113.88.112.220. After the PPTP server function of the router is enabled, the WAN IP address becomes the
address of the PPTP server.
Procedures:
1. To access the configuration page, choose VPN > PPTP Server.
2. PPTP Server: set to .
3. IP Address Pool: Set the range of IP addresses that the PPTP server assigns to devices. You are
recommended to keep the default settings.
4. MPPE Encryption: Set to , and configure the number of MPPE encryption bits, which
is 128 in this example.
5. User Name, Password: Set user names and passwords that devices use for VPN dialing up, which are
admin1 in this example.
6. Click +New.
7. Click Save.
--End
Verification (Example: Windows 7)
On business trip, Michael succeeds in accessing resources on his computers FTP server at home. The following
describes the steps:
66
1. Click at the lower-right corner of the desktop, and click Open Network and Sharing Center.
2. Click Set up a new connection or network.
3. Click Connect to a workplace > Next.
67
4. Click Use my Internet connection (VPN). If a dialog box appears, you can follow the onscreen
instructions to perform operations.
5. Enter the IP address of the PPTP server in the Internet address text box, which is 113.88.112.220 in this
example. Then click Next.
68
6. Enter the user name and password for connecting to the PPTP server, which are admin1 in this example.
Click Create.
7. Click Click Now after a while.
69
8. Access the resources on the FTP Server at home by the server or My Computer.
Method: “ftp: //Server IP address: Service port number, which is ftp: //192.168.0.104:21 in this
example.
9. Access successfully. See the following figure:
70
9.2 Online PPTP Users
This page enables you to have detailed information about the VPN devices dialed up to the PPTP server.
To access the page, select VPN > Online PPTP Users.
Parameter description:
Parameter
Description
User Name
It specifies the user name for a user to dial in the PPTP server.
Dial-in IP
Address
It specifies the IP address of a device. If the device is a router, IP address of the WAN port
which enables VPN function will be displayed.
Assigned IP
Address
It specifies the IP address that the PPTP server assigns to a device.
Uptime
It specifies the time that has elapsed since the PPTP device dials in the server successfully
this time.
71
9.3 PPTP/L2TP Client
9.3.1 Overview
You are allowed to set router as a PPTP/L2TP client on the PPTP/L2TP Client page.
The router can connect to PPTP/L2TP server after the PPTP/L2TP Client function is enabled.
Example: If users subscribe to the VPN service provided by their ISP when having broadband, they can dial in
their ISP’s VPN network through the PPTP/L2TP Client function of the router.
To access the configuration page, click VPN > PPTP/L2TP Client.
The following figure appears after enabling the PPTP/L2TP Client function:
72
Parameter description:
Parameter
Description
PPTP/L2TP Client
Used to enable/disable the PPTP/L2TP Client function. After the function is enabled, the
router works as a VPN client.
Client Type
It specifies whether the router is a PPTP client or an L2TP client.
Server IP
Address/Domain
Name
It specifies the IP address or domain name of the PPTP/L2TP server to which the router
is to be connected.
User Name
It specifies the user name and password assigned by the PPTP/L2TP server to the
PPTP/L2TP client.
Password
Status
It specifies the current connection status of a VPN client.
9.3.2 Example
Scenario
Michael subscribed to PPTP service provided by ISP when he had broadband. Assume that the VPN service
information provided by his ISP is as follows:
PPTP Server Address: 1.1.1.1
User name/Password: 123
Michael bought an AC10/AC10U for network. Now he wants to access VPN resources provided by his ISP.
Solution
The PPTP Client function could address this requirement. Set the PPTP Client function on his router. Then clients
in LAN network could access the VPN resources provided by the ISP.
Procedures:
1. Click VPN > PPTP/L2TP Client.
2. PPTP/L2TP Client: Switch the button to .
3. Client Type: Select client type, which is PPTP in this example.
4. Server IP/Domain Name: Enter the PPTP server’s IP address or domain name, which is 1.1.1.1 in this
example.
5. User Name, Password: Set user name and password that client uses for VPN dialing up, which are 123 in
this example.
6. Click Connect.
73
--End
Verification
Clients in LAN network could access the VPN resources provided by the ISP.
74
10 USB App
10.1 Overview
The USB App function includes the Share File feature. This feature allows you to share the files of a connected
USB device with LAN devices or internet devices. If you insert a portable USB device to the router, the USB app
function is enabled automatically. Otherwise, this function is disabled. For the USB App page, see the following
figure:
AC10U supports the USB App function, but AC10 does not own this function.
To access the USB App page, click USB App > Share File.
75
After you switch the Allow Internet Access button from to , the following figure appears:
76
Parameter description:
Parameter
Description
FTP Server
It specifies one of the built-in servers of your router which supports the File Transfer Protocol
(FTP). You can access the USB resources of your router through this server.
Encoding Type
It specifies the encoding type for every language in the world.
- Unicode (utf-8): It is an encoding type for all languages which is acceptable worldwide.
- Simplified Chinese (GBK): It is an encoding type for simplified Chinese.
- Traditional Chinese (Big5): It is an encoding type for traditional Chinese.
Allow Internet
Access
It specifies whether to allow internet devices to access the USB resources of your router
through the FTP server.
- If you set the button to , devices in the internet can access the USB resources of
the router.
- If not, devices in the internet cannot access the USB resources.
77
Access from
Internet
It specifies the login address internet users need to enter in address bar when they try to
access the USB resources through the FTP server. This address changes with the WAN IP
address of your router. 21 in the box is the control port of the FTP protocol. If not necessary,
you are recommended to keep the default settings.
LAN Address
It specifies the login address LAN users need to enter in address bar when they try to access
the USB resources through the FTP server. This address changes with the LAN IP address of
your router. LAN users can also visit FTP server using ftp://tendawifi.com which does not
change with LAN IP address of your router.
Samba Server
It specifies one of the built-in servers of your router which supports the Server Messages Block
(SMB) protocol. You can access the USB resources of your router through this server.
Only LAN devices can access the USB resources through the samba server.
Access from
Windows OS
It specifies the login address LAN users need to enter in address bar when they try to access
the USB resources through the samba server on a device with windows operating system. This
address changes with the LAN IP address of your router. LAN users using devices with
windows operating systems can visit samba server using \\tendawifi.com for all time.
Access from
MAC OS
It specifies the login address LAN users need to enter in address bar when they try to access
the USB resources through the samba server on a device with MAC operating system. This
address changes with the LAN IP address of your router. LAN users using devices with MAC
operating systems can visit samba server using smb://tendawifi.com for all time.
Role
It specifies the account allowed to access the USB resources through FTP/samba server of
your router. The servers only allow two accounts for visiting: one administrator and one guest.
- Administrator: After visiting the servers of the router through this account, the user not
only can view the files in the USB device, but also edit, delete or move the files and so on.
- Guest: Guest account is used for another user (except the administrator) to visit the
servers of your router.
User Name
It specifies the user name of an account used to visit the FTP/samba server of your router. The
user name of administrator account is admin for all time. The default user name of guest
account is guest1, but you can customize it yourself.
Password
It specifies the password of an account used to visit the FTP/samba server of your router. The
default password of administrator account is admin, and guest account is guest1. But you can
customize these two parameters yourself.
Permission
It specifies the operation allowed for an account to perform on the USB resources of your
router, which includes Read and Read/Write.
- Read: It specifies the account is only allowed to view/download the files in the USB
device, but not to edit, delete or move the files.
- Read/Write: It specifies the account is allowed not only to view/download the files in the
USB device, but also edit, delete or move the files and so on. Permission for
administrator account is Read/Write all the time.
78
10.2 Modifying role information
In this module, both the default user name and password of administrator are admin, and you are only allowed
to modify the password of administrator. Both the default user name and password of guest are guest1, and you
can customize these two parameters yourself. The permission for administrator is Read/Write for all time, while
the default permission for guest is Read but you can modify it as required.
10.2.1 Example
Procedure:
1. Access the web UI of your router, then click USB App > Share File.
2. Clear the default user name for guest, default passwords for administrator or guest, and enter your
desired user name and passwords.
3. To modify the permission for guest, select your desired permission from the drop-down-list box.
4. Click Save.
79
--End
Verification
Modification succeeds. See the following figure:
80
If the user name or password of either account is modified, you need to enter the new user name or
password to visit the FTP/samba server next time.
10.3 Accessing USB resources through FTP/Samba
servers
10.3.1 Accessing the USB resources from a LAN device
Procedure: (FTP server is used as an example here)
1. Insert your USB (KINGSTON-b in this example) to the USB port of AC10U. You can check whether your
USB is connected to the router properly on Internet Status page.
2. Log in to the web UI of your router, then click USB App > Share File.
81
3. Record the LAN address used to visit the FTP server, which is ftp://192.168.0.1:21 in this example.
4. Click My Computer in a computer connected to your router. Enter ftp://192.168.0.1:21 in the address
bar, and press Enter.
5. Enter your user name and password, which are both admin in this example, and click log on.
82
--End
Verification
Access the USB resources of your router successfully. See the following figure:
10.3.2 Accessing the USB resources from an internet device
Procedure: (FTP server is used as an example here)
1. Insert your USB (KINGSTON-b in this example) to the USB port of AC10U. You can check whether your
USB is connected to the router properly on Internet Status page.
2. Log in to the web UI of your router, then click USB App > Share File.
83
3. Set the Allow Internet Access button to and click Save on the bottom of the page.
84
4. Access the configuration page again, and record the address used to visit the FTP server for internet
devices, which is ftp://192.168.20.133:21 in this example.
5. Click My Computer in a computer not connected to your router. Enter ftp://192.168.20.133:21 in the
address bar, and press Enter.
6. Enter your user name and password, which are both admin in this example, and click log on.
85
--End
Verification
Access the USB resources of your router successfully. See the following figure:
86
11 Advanced Settings
This module includes: Bandwidth Control, Tenda App, Sleeping Mode, LED Control, Filter MAC Address, Firewall,
IPTV, Static Route, DDNS, Virtual Server, DMZ Host, UPnP.
11.1 Bandwidth Control
11.1.1 Overview
This page allows you to view information about online devices, and set upload limits or download limits for
devices if needed.
To access the configuration page, click Advanced Settings > Bandwidth Control.
Parameter description:
Parameter
Description
Device Name
It presents information about a device that has connected to the router, including
name, IP address. You can change the device name by clicking .
Upload/Download
Speed
It specifies the current upload and download speeds of a device.
Upload/Download
Limit
It specifies the maximum upload/download speed of a device. You can select your
preferred maximum upload/download from the drop-down box, or entering the
speed manually.
87
11.1.2 Example
Scenario
Michael bought an AC10/AC10U for network after having broadband. He needs to set download limit for every
device to ensure all family members can have good internet experience.
Procedures:
1. Click Advanced Settings > Bandwidth Control.
2. Download Limit: Set download limit to a value for the devices in the list, which is 2Mbps in this
example.
3. Click Save.
--End
Verification
The maximum download speed for each device in the list is 2 Mbps, which allows each device to see HD videos
and surf the internet normally.
11.2 Tenda App
11.2.1 Overview
App management on this router allows you to manage it wherever and whenever you are. You can use Tenda
WiFi app to:
Manage your router in LAN.
88
Manage your router remotely over the internet.
To access the Tenda App page, click Advanced Settings > Tenda App.
11.2.2 Example
The following figure may help you understand how to manage the router remotely using Tenda WiFi.
Procedures:
Step 1 Install Tenda WiFi app.
Download Tenda WiFi in app store of your smart phone.
Step 2 Register a Tenda account.
1. Open Tenda WiFi and enter the login password of your router (if any) in the password box. Click Log.
2. Click for registration. (Example: Email address)
89
3. Choose your registration type, which is Email address in this example.
4. Email address: Enter the email address you want to set as an account name, which is
12345678901@163.com in this example.
5. Password: Set a password for your Tenda account.
6. Click Register.
7. The activation email has sent to your email address. Please tap click here to confirm to activate in valid
time.
90
8. Your account is activated successfully.
Step 3 Log in to the web UI of the router, and enable the Tenda App function.
1. Log in to the web UI of the router. Then click Advanced Settings > Tenda App.
2. Manage with Tenda App: Switch the button to .
3. Account: Enter the account registered in your Tenda WiFi app.
4. Click Save.
--End
Verification
When you are not at home, you can use Tenda WiFi app to manage the router by connecting your smart phone
to WiFi network or traffic.
91
11.3 Sleeping Mode
This router supports Sleeping Mode function. When this function takes effect, LED indicators and WiFi network of
this router will be disabled.
The Sleeping Mode function works based on time settings. If the system time of the router is not
synchronized with the internet time, this function cannot work properly.
To access the configuration page, click Advanced Settings > Sleeping Mode. By default, the Sleeping Mode
function is disabled.
The following figure appears after the Sleeping Mode function is enabled:
92
Parameter description:
Parameter
Description
Sleeping Mode
Used to enable/disable the Sleeping Mode function..
When the router is in Sleeping mode, you can enable the WiFi network function by pressing
the WIFI button on the rear panel of the router or using Tenda WiFi app. For details about
how to enable this WiFi network function by Tenda WiFi app, refer to the usage of the app.
Sleeping Time
It specifies the time when the Sleeping Mode function is effective.
Delay
-
When Delay enabling the Sleep mode when there is an online user option is selected, if
device (s) exchange(s) data with the router in a WAN speed of no more than 3KB/s within
30 minutes, the router enters Sleeping mode; if no device exchanges data with the router,
and the traffic is less than 3 KB/s within 3 minutes, the router enters Sleeping mode.
-
When the Sleeping Mode function is enabled and the Delay enabling the Sleep mode
when there is an online user option is not selected, the router enters Sleeping mode
during Sleeping Time automatically.
11.4 LED Control
This page allows you to set on/off status of the routers LED indicators.
To access the configuration page, click Advanced Settings > LED Control.
93
Parameter description:
Parameter
Description
Always on
It indicates that all the LED indicators work in ordinary states.
Always off
It indicates that all the indicators are off even the router is working.
Schedule
In specifies that all the LED indicators are turned off at the duration of Turn Off During, but
return to their ordinary states when the periods expire.
11.5 Filter MAC Address
11.5.1 Overview
Usually computers and smart phones have their own MAC addresses.
The Filter MAC Address page allows you to add a filter rule and set internet limit for devices with specific MAC
addresses, including To disallow listed devices to access the internet and To allow only the listed devices to
access the internet.
To access the configuration page, click Advanced Settings > Filter MAC Address.
94
Parameter description:
Parameter
Description
MAC Address Filter
Mode
It specifies whether the listed devices are allowed to access the internet through the
router.
-
Whitelist: It specifies that only the listed devices can access the internet through
the router.
-
Blacklist: It specifies that the listed devices cannot access the internet through the
router.
Blacklisted/Whitelisted
Device
Enter names of devices that you want to add in blacklist or whitelist.
MAC Address
Enter MAC addresses of devices that you want to add in blacklist or whitelist.
Operation
Click +New to add the device to blacklist or whitelist.
Add all online devices
to the whitelist
Click this link to add all online devices to the whitelist. This link is only available for
Whitelist.
This link only appears when you set the whitelist for the first time.
11.5.2 Adding a MAC address filter rule
1. To access the configuration page, click Advanced Settings > Filter MAC Address.
2. MAC Address Filter Mode: Select your MAC address filter mode, which is Blacklist in this example.
95
3. Blacklisted Device: Set the device that you disallow to access the internet through your router, which is
Michael’s Phone in this example.
4. MAC Address: Enter the MAC address of the blacklisted device, which is C8:3A:35:13:05:18 in this
example.
5. Click +New.
6. Click Save.
--End
11.5.3 Deleting a MAC address filter rule
1. To access the configuration page, click Advanced Settings > Filter MAC Address.
2. Select the rule you want to delete, and click .
3. Click Save on the bottom of the page.
96
--End
11.5.4 Example
Scenario
Michael bought an AC10/AC10U for network. He finds unknown devices in module Attached Devices of the
router. But he hopes to allow only devices owned by his family members to access the internet through the
router.
Solution
The Filter MAC Address function of the router can address this requirement.
Assume that the devices owned by his family members have following MAC addresses:
4C:CC:6A:AD:14:53
14:5F:94:BC:FC:81
1C:5C:F2:B4:40:01
Procedures:
1. To access the configuration page, click Advanced Settings > Filter MAC Address.
2. MAC Address Filter Mode: Select Whitelist.
3. Whitelisted Device: Enter name of the device allowed to connect to the router, which is Phone-1 in this
example.
4. MAC Address: Enter MAC address of the device allowed to connect to the router, which is
14:5F:94:BC:FC:81 in this example.
5. Click +New.
97
6. Refer to step 3-5 for adding MAC address 4C:CC:6A:AD:14:53.
7. Click Save.
--End
Verification
Only devices with MAC address 4C:CC:6A:AD:14:53, 14:5F:94:BC:FC:81 or 1C:5C:F2:B4:40:01 can access the
internet through the router.
11.6 Firewall
The firewall can protect the router against some common DoS attacks such as ICMP Flood Attack, TCP Flood
Attack, and UCP Flood Attack. It also ignores Ping packets from the WAN port as well, helping ensure network
security.
To access the configuration page, click Advanced Settings > Firewall. By default, the Firewall function is enabled.
You are recommended to retain the default settings.
98
Parameter description:
Parameter
Description
ICMP Flood Attack
Defense
Used to enable/disable the ICMP flood attack defense.
ICMP Flood Attack is an attack using ICMP packets.
If an attacker sends many ICMP ECHO packets to destination host, which results in ICMP
flood. Then destination host pays much time and resources on ICMP ECHO packets but
nothing on normal requests or responses, which achieves attack against destination
host.
TCP Flood Attack
Defense
Used to enable/disable the TCP flood attack defense.
In TCP protocol, when one device sends connection request and initialization to a server,
protocol stack in the server will leave Backlog Quene for information exchange in
connecting process.
Attackers make use of Backlog Quene and send TCP connection requests only with SYN
to the server many times by special program. Server will regard those requests as
uncompleted and establish sessions for them in Backlog Queue.
If those SYN requests are more than what server can hold, Backlog Queue will be full.
Then server will not accept new request so that other legal connection will be refused.
UCP Flood Attack
Defense
Used to enable/disable the UCP flood attack defense.
UCP Flood Attack works on the similar principle as ICMP Flood Attack. If an attacker
sends many UDP packets to destination host, the destination host pays much time and
resources on UDP packets but nothing on normal packet requests or responses, which
achieves attack against the destination host.
Ignore Ping Packet
Form WAN Port
It specifies whether to ignore ping packets from WAN port.
When host in the internet tries to ping WAN IP address of the router, the router will
ignore that ping request automatically, protecting itself from exposure to the internet
and external Ping attack.
99
11.7 IPTV
11.7.1 Overview
IPTV is the abbreviation of Internet Protocol Television. It is new technology integrating with internet, multimedia,
telecommunication and many other technologies, providing interactive services including digital TV to family
users by internet broadband lines. IPTV is a service provided by ISP. Uses can have multiple IPTV programs by IP
set-top-box and television at home.
To access the configuration page, click Advanced Settings > IPTV.
The following figure appears after IPTV is enabled:
Parameter description:
Parameter
Description
IPTV
Used to enable/disable the IPTV function of the router. When this function is enabled, the
third LAN port of this router can be used only as IPTV port and connect IPTV set-top-box, but
cannot access other devices such as computer.
VLAN
It specifies the VLAN ID of your IPTV service.
-
If you do not have any information about VLAN provided by your ISP when having IPTV
100
Parameter
Description
service, please keep Default.
-
If you have VLAN ID from your ISP when having IPTV service, please choose Custom VLAN
and enter the VLAN value.
-
If you have IPTV service in Shanghai, please choose Shanghai VLAN and click VLAN value.
11.7.2 Example
Scenario
Michael subscribed to IPTV service when he had broadband. His ISP provided IPTV account and password but no
information about VLAN. After buying an AC10/AC10U for network, he wants to have IPTV program.
Solution
The IPTV function of the router can address this requirement. Network topology is shown as follows:
Procedures:
Step 1 Set you router
1. To access the configuration page, click Advanced Settings > IPTV.
2. IPTV: Switch the button to .
3. Click Save.
101
Step 2 Set your set-top-box
Dial up on set-top-box with the account and password provided by ISP.
--End
Verification
Michael can have IPTV programs on television.
11.8 Static Route
11.8.1 Overview
Routing is performed to select the best route for delivering data from a source address to a destination address.
A static route is a manually configured route which is simple, efficient, and reliable. Appropriate static routes help
reduce route selection problems and data overload of route selection, improving the packet forwarding speed.
To access the configuration page, click Advanced Settings > Static Route.
102
Parameter description:
Parameter
Description
Destination
Network
It specifies the destination IP address of a packet.
Subnet mask
It specifies the subnet mask of a packet’s destination IP address.
Gateway
It specifies the IP address of the next hop of packet transmitted from the router.
WAN
It specifies router’s WAN port where packets leave the router.
Operation
It allows you to add/delete a static route rule.
11.8.2 Example
Scenario
Michael used wired router and switch for network in the past. Now he purchases an AC10/AC10U for wireless
coverage and builds office intranet on that network, requiring devices connected to AC10/AC10U able to access
both the internet and office intranet.
Solution
The following figure shows a network topology for reference:
103
Router 1 accesses the internet and Router 2 to the intranet. AC10/AC10U gets IP address to access the internet
from Router 1 automatically. Set static route on AC10/AC10U, achieving LAN devices access both the internet and
intranet.
Assume that the devices have following MAC addresses:
AC10/AC10U LAN IP Address: 192.168.0.1
Router 1 LAN IP Address: 192.168.1.10
Router 2 LAN IP Address: 192.168.1.20
Assume that the intranet has following information:
Address: 172.16.105.10
Subnet Mask: 255.255.255.0
Procedures:
Step 1 Set Router 1 to access the internet. Please refer to the installation guide/user guide of the router for
detailed steps. Set Router 2 to access the intranet and disable the DHCP function of this router. Please
refer to the installation guide / user guide of the router for detailed steps.
Step 2 Set AC10/AC10U to access the internet by dynamic IP address. Please refer to 5.3 Setting up an internet
connection with a dynamic IP address in this user guide for detailed steps.
104
Step 3 Set a static route rule on AC10/AC10U.
1. To access the configuration page, click Advanced Settings > Static Route.
2. Destination Network: Enter IP address of the destination network, which is 172.16.105.0 in this
example.
3. Subnet mask: Enter subnet mask of the destination IP address, which is 255.255.255.0 in this example.
4. Gateway: Set Gateway to the LAN IP address of Router 2, which is 192.168.1.20 in this example.
5. Click +New.
--End
Configuration succeeds.
105
Verification
Devices connected to the router can access both the internet and the intranet.
11.9 DDNS
11.9.1 Overview
WAN IP address is needed when Virtual Server, DMZ Host, and Tenda App function are enabled. If routers WAN
IP address changes, these functions will not work properly. The DDNS function allows you to map a dynamic WAN
IP address (public IP address) of the router to a static domain name, helping internet users (WAN side) access the
router by static domain name.
If you dislike remembering complex IP addresses, you can enable the DDNS function. To access the configuration
page, click Advanced Settings > DDNS.
The following figure appears after DDNS is enabled:
106
Parameter description:
Parameter
Description
DDNS
Used to enable/disable the DDNS function. By default, this function is disabled.
Service
Provider
It specifies a DDNS service provider. AC10/AC10U supports service provider no-ip.com,
3322.org, dyndns.org, 88ip.cn, and oray.com.
User Name
It specifies the user name registered on a DDNS service provider's website for logging into the
DDNS service.
Password
It specifies the password registered on a DDNS service provider's website for logging into the
DDNS service.
Domain Name
It specifies the DDNS domain name registered on a DDNS service provider's website. If this
item does not appear after you select service provider, you do not need to enter a domain
name manually.
Connection
Status
It specifies whether the DDNS service is configured successfully.
11.9.2 Adding a DDNS rule
1. To access the configuration page, click Advanced Settings > DDNS.
2. DDNS: Switch to .
3. Service Provider: Choose your DDNS service provider.
If you do not have a DDNS account, please select a service provider and click Register to have one on the
website of the service provider. After successful registration, log in to the DDNS configuration page to
configure again.
4. Set User Name, Password, and Domain Name.
5. Click Save.
107
--End
When the Connection Status displays Connected, the configuration succeeds.
11.9.3 Example
Scenario
Michael bought an AC10/AC10U for network after having broadband. He wants to make a web server built on
LAN accessible to the internet, and internet users can visit that server by static domain name.
The following figure shows the scenario:
108
Solution
This requirement can be addressed by Virtual Server function and DDNS function. Assume that the intranet web
server has following information:
Server IP Address: 192.168.0.110
MAC Address of the Server Host: C8:3A:35:13:05:18
User Name/Password: admin/admin
Server Port: 80
Procedures:
Step 1 Register a domain name.
1. To access the configuration page, click Advanced Settings > DDNS.
2. DDNS: Switch to .
3. Service Provider: Select a DDNS service provider, which is dyndns.org in this example, and click
Register.
Visit by domain name
109
4. Register on the website of the selected DDNS service provider. Assume the registered information are
listed as follows:
- Service Provider: dyndns.org
- User Name: Tenda
- Password: 12345678
- Domain Name: tenda.dyndns.org
Step 2 Set DDNS
1. To access the configuration page, click Advanced Settings > DDNS.
2. DDNS: Switch to .
3. Service Provider: Select dyndns.org from drop-down-box.
4. User Name: Enter the user name registered on DDNS service provider's website, which is Tenda in this
example.
5. Password: Enter the password registered on DDNS service provider's website, which is 12345678 in this
example.
6. Domain Name: Enter domain name registered on DDNS service provider's website, which is
tenda.dyndns.org in this example.
7. Click Save.
Wait until the connection status changes to Connected.
110
Step 3 Set Virtual Server function. For detailed steps, please refer to 11.10 Virtual Server in this guide.
--End
Verification
The visit path for internet users to access intranet resources is: http://domain name: server port, which is http://
tenda.dyndns.org.net:80 in this example. Then perform according to onscreen instructions.
11.10 Virtual Server
Usually, internet users cannot access LAN through router, but internet users can visit LAN resources on router by
enabling virtual server. After the Virtual Server function is configured, if one host in LAN has Web or FTP server,
internet users can access that server successfully.
To access the configuration page, click Advanced Settings > Virtual Server.
111
Parameter description:
Parameter
Description
Internal IP
Address
It specifies the IP address of an internal server.
LAN Port
It specifies the service port number of a server that resides on the LAN of the router.
Click drop-down list box, and select corresponding service port number; or enter service
port number manually. See the following figure:
WAN Port
It specifies a router port accessible to internet users. WAN port will be populated
automatically after you select LAN port.
Protocol
It specifies the protocol of a service. If you are uncertain about which service protocol is
used, TCP/UDP is recommended.
Operation
It allows you to add/delete a virtual server rule.
112
11.10.1 Adding a virtual server rule
1. To access the configuration page, click Advanced Settings > Virtual Server.
2. Internal IP Address: Enter IP address of the internal sever, which is 192.168.0.110 in this example.
3. LAN Port: Click drop-down list box and select internal service port number or enter the number
manually, which is 21 in this example.
4. Protocol: Select protocol of a service from the drop-down list box, which is TCP&UDP in this example.
5. Click +New.
--End
The rule is added successfully. See the following figure:
11.10.2 Deleting a virtual server rule
1. To access the configuration page, click Advanced Settings > Virtual Server.
2. Select the rule you want to delete, and click .
--End
113
11.10.3 Example
Scenario
Michael bought an AC10/AC10U for network after having broadband. He wants to make the web server built on
LAN accessible to internet users.
The following figure shows the scenario:
Solution
This requirement can be addressed by the Virtual Server function.
Assume that the internal web server information is listed as follows:
Server IP Address: 192.168.0.110
MAC Address of the Server Host: C8:3A:35:13:05:18
User Name/Password: admin/admin
Server Port: 80
Procedures:
Step 1 Configure the Virtual Server function
1. To access the configuration page, click Advanced Settings > Virtual Server.
2. Internal IP Address: Enter IP address of the internal web server, which is 192.168.0.110 in this example.
3. LAN Port: Click drop-down list box and select internal service port number, which is 80(HTTP) in this
example.
4. Protocol: Select protocol of a service from the drop-down list box, which is TCP&UDP in this example.
5. Click +New.
Visit by IP address
WAN IP102.33.66.88
114
The rule is added successfully, see the following figure:
Step 2 Assign static IP address to the host on which the server is built.
1. Select System Settings > DHCP Reservation.
2. Device Name: Set a name for the host, which is Web Server in this example.
3. MAC Address: Enter the MAC address of the host, which is C8:3A:35:13:05:18 in this example.
4. IP Address: Enter the static IP address assigned to the host, which is 192.168.0.110 in this example.
5. Click +New.
--End
The DHCP reservation rule is added successfully. See the following figure:
115
Verification
Internet users visit this web server in the form of “Protocol: //WAN IP address: external port, which is
http://102.33.66.88:80 in this example. Then perform according to onscreen instructions.
If you want to visit that server by domain name, you can try the “Virtual Server+DDNS” method.
11.11 DMZ Host
The DMZ Host function If you can set a computer in LAN as DMZ host, that computer will become available to the
internet completely, which achieves unlimited bidirectional communication. When you play games or have video
meeting on some computer, you can set it as DMZ host for better user experience.
To access the configuration page, click Advanced Settings > DMZ Host. By default, the DMZ Host function is
disabled.
-
A DMZ host is not protected by the firewall of the router because the host is exposed to the internet
completely. A hacker may leverage the DMZ host to attack your LAN. Therefore, enable the DMZ
function only when necessary.
-
Manually set a static IP address for a DMZ host, to prevent changes of dynamic IP address which lead
to DMZ function failures.
-
Security software, antivirus software, and the built-in OS firewall of the computer may cause DMZ
function failures. Disable them when using the DMZ function. If the DMZ function is not required, it is
recommended that you disable it and enable your firewall, security, and antivirus software.
11.11.1 Setting a computer to DMZ host
1. To access the configuration page, click Advanced Settings > DMZ Host.
116
2. DMZ Host: Set to .
3. DMZ Host IP Address: Enter the last part of the IP address of the computer to be set to DMZ host, which
is 110 in this example.
4. Click Save.
--End
11.12 UPnP
Universal Plug and Play (UPnP) is a set of networking protocols. This function enables the router to open ports for
LAN apps supporting UPnP, which improves user experience.
To access the configuration page, click Advanced Settings > UPnP.
After UPnP is enabled, port transfer information displays on the configuration page when UPnP application, such
as Thunder, is running in the LAN network. Port transfer information is provided when apps make requests. See
the following figure:
117
118
12 System Settings
This module includes the following functions: LAN Settings, DHCP Reservation, WAN Settings, Time Settings,
Login Password, Reboot and Reset, Firmware Upgrade, Backup/Restore, Remote Management, System Status,
System Log, and Automatic Maintenance.
12.1 LAN Settings
12.1.1 Overview
This module enables you to do the followings:
Modify the LAN IP address of the router.
The LAN IP address is the management IP address of the router, which is 192.168.0.1 by default but can be
modified if necessary.
Modify parameters of DHCP server.
If the DHCP Server function is enabled, the DHCP server can automatically assign IP addresses, subnet mask,
gateway and other internet parameters to the devices connected to the router. If this function is disabled,
you have to manually set the IP address settings on your devices to access the internet. You are
recommended to retain the DHCP Server function enabled.
Configure the DNS information assigned to devices.
To access the configuration page, click System Settings > LAN Settings.
Parameter description:
119
Parameter
Description
LAN IP Address
It specifies the LAN IP address of the router, which is the IP address used to log in to
the web UI of the router.
You can log in to the web UI of the router through either IP address (default:
192.168.0.1) or the domain name (tendawifi.com).
Subnet Mask
It specifies the subnet mask of the IP address of the router.
DHCP
Server
IP Address
Range
It specifies the IP addresses assigned by the DHCP server to devices, which ranges
from 192.168.0.100 to 192.168.0.200 by default.
Lease Time
It specifies the validity period of an IP address assigned by the DHCP server to a
device. When the lease time expires:
- If the device is still connected to the router, the device automatically extends the
lease time and continues to use this IP address.
- If the device has been disconnected (shutdown, or the Ethernet cable between
the device and the router has been removed) from the router, the router
recycles the IP address. The router assigns this IP address to other devices
requested for IP addresses.
You are recommended to retain the default value.
DNS
Settings
Primary
DNS Server
It specifies the primary DNS server IP address assigned by the DHCP server to LAN
devices.
Generally, you are recommended to retain the default configuration. If it is
necessary to change the default configuration, please set this parameter
to a correct DNS server IP address or DNS proxy IP address, to enable
devices to access the internet.
Secondary
DNS Server
It specifies the secondary DNS server IP address assigned by the DHCP server to
devices. This parameter is optional. If it is empty, the DHCP server does not assign it
to devices.
12.1.2 Changing the LAN IP address
1. To access the configuration page, click System Settings > LAN Settings.
2. LAN IP Address: Modify the LAN IP Address, which is 192.168.3.1 in this example.
3. Click Save in the bottom of the page.
120
--End
Wait till the modification completes successfully, you will be redirected to the login page. If you fail to log in to
the web UI of the router, ensure that the local connection of your computer is set to Obtain an IP address
automatically. Then release the current IP address of your computer and try to log in again after your computer
get new IP address. If the problem still persists, please try logging in again using tendawifi.com. For details about
how to set local area connection of your computer, please refer to A1 Setting the IP address of your computer in
the appendixes. To release the current IP address of your computer, disconnect the Ethernet cable between your
router and computer for a while, and reconnect it soon.
12.2 DHCP Reservation
This function allows the device to obtain the same IP address all the time, ensuring the Virtual Server and DMZ
Host functions that requires fixed IP address take effect normally.
To access the configuration page, click System Settings > DHCP Reservation.
Parameter description:
121
Parameter
Description
Device Name
It specifies the name of the device to be bound with a fixed IP address.
MAC Address
It specifies the MAC address of a device.
IP Address
It specifies the IP address to be bound with the device indicated by the corresponding MAC
address.
Status
It indicates whether a device is connected to the router or not.
Operation
It is used to edit a DHCP Reservation rule, including four operations:
- +New : It is used to add a DHCP Reservation rule.
- : It is used to bind a device with a static IP.
- : It is used to unbind a device with a static IP.
- : It is used to delete a DHCP Reservation rule.
12.2.1 Adding a DHCP reservation rule
1. To access the configuration page, click System Settings > DHCP Reservation.
2. Device Name: Enter the device name used to assign static IP addresses, which is Web Server in this
example.
3. MAC Address: Enter the MAC address of the device, which is C8:3A:35:13:05:18 in this example.
4. IP Address: Enter the static IP address assigned to the device, which is 192.168.0.110 in this example.
5. Click +New.
--End
The DHCP reservation rule is added successfully. See the following figure:
12.2.2 Deleting a DHCP reservation rule
1. To access the configuration page, click System Settings > DHCP Reservation.
122
2. Locate the rule you want to delete, and click .
--End
12.3 WAN Settings
12.3.1 Overview
This module enables you to modify MTU, speed and MAC address of the WAN port. If you cannot access the
internet after configuring the internet settings, try modifying the WAN parameters.
To access the configuration page, click System Settings > WAN Settings.
Parameter description:
Parameter
Description
MTU
Maximum transmission unit (MTU). It specifies the size of the largest data packet that can
be transmitted across the network devices. You are recommended to retain the default
value.
Speed
It specifies the speed of the WAN port of the router.
If the LED indicator of the WAN port is off, or does not turn on until 5 seconds later under
the circumstance that the quality Ethernet cable has been connected correctly, you can
select 10 Mbps FDX or 10 Mbps HDX from the drop-down list box of Speed.
Otherwise, you are recommended to retain the default configuration 1000 Mbps
123
Parameter
Description
Auto-negotiation.
MAC Address
It is used to clone the MAC address accessible to the internet to the WAN port of the
router. If the router cannot access the internet after you configure the internet settings, it
is perhaps that the ISP has bound the connection information with a MAC address. In this
case, you can try to clone the MAC address, and try to access the internet again.
- Default: It is used to restore the MAC address of the WAN port of the router to factory
settings.
- Clone local MAC address: It is used to set the MAC address of the WAN port to the
MAC address of the current device managing the router.
- Set MAC address: It is used to set the MAC address of the WAN port manually.
12.3.2 Changing MTU value
You are recommended to retain the default value of MTU, unless the following cases happen:
Websites are inaccessible, or you cannot log in to some secure websites (such as paypal login page).
Email service fails, or FTP, POP and other servers are inaccessible.
In these cases, you can try to decrease the MTU value from the maximum one (recommended range: 1400-1500),
till the problem is resolved.
MTU
Description
1500
It is commonly used for ADSL and non-VPN dial-up connections.
1492
It is used for PPPoE dial-up connections.
1472
It is the maximum value for the ping command. (A packet with a size larger than 1472 is
splitted.)
1468
It is used for DHCP connections.
1436
It is used for VPN or PPTP connections.
12.3.3 Changing the MAC address of the WAN port
Ensure that the MAC address to be cloned is correct! Before you have AC10/AC10U, the MAC address of
your computer that can access to the internet through the Ethernet jack, or the WAN MAC address of
your original router that can access to the internet, is the correct MAC address you should clone.
1. To access the configuration page, click System Settings > WAN Settings.
2. MAC Address: Select Clone local MAC address or Set MAC address from the drop down list box. If you
select Set MAC address, enter the MAC address that you want to clone. If you select Clone local MAC
address, configure this function on the computer with a correct MAC address.
3. Click Save.
124
--End
To verify if cloning MAC address is successful, choose System Settings > System Status, if the MAC address under
the WAN Status is same as the MAC address you select to clone, MAC address cloning succeeds. If the internet is
inaccessible after you clone the MAC address successfully, contact your ISP to resolve this issue.
12.4 Time Settings
12.4.1 Overview
This module enables you to set the system time of the router. Correct system time of the router makes
time-based functions take effect successfully, such as the WiFi Schedule, Parental Control, LED Control, Sleeping
Mode, and Automatic Maintenance functions. Please keep the system time of your router correct.
To access the configuration page, click System Settings > Time Settings.
The default time zone of the router is (GMT+08:00) Beijing, Chongqing, Hong Kong, Urumqi, Taipei. After
connected, the router automatically synchronizes its system time with the time zone you select.
125
12.5 Login Password
12.5.1 Overview
This module enables you to modify the login password of the router. The login password is used to log in to the
web UI of the router. By default, the router has no login password. You are recommended to configure a login
password when you set up the router for the first time.
To access the configuration page, click System Settings > Login Password.
12.5.2 Changing the login password
1. To access the configuration page, click System Settings > Login Password.
2. New Password: Set a new login password.
3. Confirm Password: Enter the new login password again.
4. Click Save.
--End
You will be redirected to the login page. Enter the new login password, and click Login to login to the web UI
126
of the router.
12.6 Reboot and Reset
12.6.1 Overview
This module enables you to reboot the router or restore the router to factory settings.
If a setting does not take effect or the router does not work properly, you can try rebooting the router to
resolve the problem.
If the internet is inaccessible for unknown reasons, or you forget the login password, you are recommended
to restore the router to factory settings and reconfigure it. The router can be reset through the web UI or
holding down the RST/WPS button on the back panel of the router for 8 seconds. After resetting the router,
refer to Chapter 2 Set up to access the internet to configure your router for internet connection.
To access the configuration page, click System Settings > Reboot and Reset.
127
12.6.2 Rebooting the router
1. To access the configuration page, click System Settings > Reboot and Reset.
2. Click Reboot.
--End
12.6.3 Resetting the router
Resetting the router deletes all your current configuration. You need to reconfigure the router to access
the internet. Ensure that the power supply of the router is properly when the router is resetting.
Resetting the router via the web UI
1. To access the configuration page, click System Settings > Reboot and Reset.
2. Click Reset. Your router is reset successfully when all the indicators blink once. Then wait for the router
to restart.
--End
128
Resetting the router via the RST/WPS button
Power on your router. When the SYS indicator blinks, hold the RST/WPS button down for about 8 seconds. Your
router is reset successfully when all the indicators blink once.
12.7 Firmware Upgrade
12.7.1 Overview
This module enables you to upgrade the firmware of the router.
Firmware upgrade offers the router with more stable performance and new functions. The router supports
Online Upgrade and Local Upgrade, and the default setting is Online Upgrade, which means the router
automatically detects whether the new firmware is available or not and displays its information if any.
To access the configuration page, click System Settings > Firmware Upgrade.
12.7.2 Steps for local upgrade
-
Before an upgrade, check if the firmware is accurate. Erroneous firmware will damage the router.
-
Do not power off the router during an upgrade. Otherwise, the router may be damaged.
-
After the firmware is upgraded, you are recommended to restore the factory settings of the router
and configure the router again, so as to ensure stability of the new firmware and proper operation of
its new functions.
1. Log in to the official website of Tenda http://www.tendacn.com and download the latest firmware to
your computer.
2. Log in to the web UI of the router, and choose System Settings > Firmware Upgrade.
3. Upgrade Type: Click Local Upgrade.
4. Select Upgrade File: Click Choose File, and select the firmware that has been downloaded to your
computer.
129
5. Click Upgrade.
--End
Wait a second for the upgrade to complete. You can go to the Internet Status page to see whether the upgrade
succeeds. If it does, reset your router and configure it again to access the internet.
12.7.3 Checking your firmware version
1. Log in to the web UI of the router, restore the router to the factory settings, and reconfigure the router.
2. After login to the web UI, click System Settings > Firmware Upgrade.
3. Check whether the current firmware version of the router is the same as the one you used for upgrade
just now.
12.7.4 Steps for online upgrade
After connecting to the internet, the router detects firmware version automatically. If new firmware is available,
you can choose Online Upgrade to upgrade the routers firmware.
1. To access the configuration page, click System Settings > Firmware Upgrade.
2. Click Upgrade.
130
--End
Wait for the upgrade to complete. You will be redirected to the login page of the router after successful upgrade.
12.8 Backup/Restore
12.8.1 Overview
This module enables you to back up the current configuration of your router to your computer, or restore your
router to a previous configuration by importing the configuration file on your computer to the router.
The module enables you to back up the router’s configuration in case that you lost all the configuration after
resetting the router. After you clicking Backup, the system generates a configuration file. If the router is restored
to factory settings, importing the configuration file can restore the router to the previous settings.
To access the configuration page, click System Settings > Backup/Restore.
Backup: It is used to back up the current configuration of the router.
Restore: It is used to restore the router to previous settings by importing the backup configuration file.
131
12.8.2 Steps for backup
1. To access the configuration page, click System Settings > Backup/Restore.
2. Click Backup.
3. Follow the onscreen instructions to backup the configuration.
--End
12.8.3 Steps for restore
1. To access the configuration page, click System Settings > Backup/Restore.
2. Click Restore, and select the configuration file to be restored.
3. Wait for the router to reboot.
--End
12.9 Remote Management
12.9.1 Overview
This module enables you to login to the web UI of the router over the internet.
Generally, only devices connected to the router can log in to the web UI of the router. But if necessary, you can to
log in to the web UI of the router remotely over the internet.
To access the configuration page, click System Settings > Remote Management.
The following figure appears after this function is enabled:
132
Parameter description:
Parameter
Description
Remote
Management
Used to enable/disable the remote management function. By default, this function is
disabled.
Remote IP
Address
It specifies the IP address that can access the router remotely.
Port
It specifies the port number needed when you manage the router remotely. The default port
number is 8080, which can be modified if necessary.
Since ports 1 to 1024 are used by well-known service, you are strongly
recommended to set the value in the range of 1025~65535 to prevent port
confliction.
12.9.2 Configuring remote management
1. To access the configuration page, click System Settings > Remote Management.
2. Remote Management: Set to .
3. Remote IP Address: Set the IP address allowed to access the router remotely.
4. Port: Set the port number used for remote access. You are recommended to keep the default value if
you do not have special requirement.
5. Click Save.
133
--End
Scenario
Michael bought an AC10/AC10U for network after having broadband. The WAN IP address of the router is
202.105.106.55. Michael needs to log in to the web UI of the router on business trip.
Solution
The remote management function can address this requirement. The following figure shows a network topology
for reference:
Procedures:
1. To access the configuration page, click System Settings > Remote Management.
2. Remote Management: Set to .
3. Remote IP Address: Enter remote IP address, which is 0.0.0.0 in this example.
Visit by IP address
WAN IP202.105.106.55
IP210.76.200.101
134
4. Port: Keep the default settings.
5. Click Save.
--End
Verification
You can log into the web UI of the router to manage it by accessing http://202.105.106.55:8080 on the remote
computer with the IP address 0.0.0.0.
12.10 System Status
This module enables you to view the basic information of the router, including the Information, WAN Status, LAN
Status, and WiFi Status sections.
To access the configuration page, click System Settings > System Status.
12.10.1 Information
This module enables you to view system time, uptime, firmware version, and hardware version. See the following
figure:
Parameter description:
135
Parameter
Description
System Time
It specifies the current system time of the router. Ensure that the router is connected to the
internet properly.
Uptime
It specifies the time that has elapsed since the router was previously started.
Firmware
Version
It specifies the current firmware version of the router. You can check whether the firmware
upgrade configured in Firmware Upgrade succeeded or not here.
Hardware
Version
It specifies the current hardware version of the router.
12.10.2 WAN Status
This module enables you to view the WAN status of the router. See the following figure:
Parameter description:
Parameter
Description
Connection
Type
It specifies the current connection type of the router.
Connection
Status
It specifies the current connection status of the router.
Connection
Duration
It specifies the time that has elapsed since the router was connected to the internet
previously.
136
IP Address
It specifies the WAN IP address of the router. This parameter is needed for when you use
functions like Virtual Server or Remote Management.
Subnet Mask
It specifies the subnet mask of the WAN IP address of the router.
Default
Gateway
It specifies the gateway assigned to the router.
Primary DNS
It specifies the primary DNS assigned to the router.
Secondary
DNS
It specifies the secondary DNS assigned to the router.
MAC Address
It specifies the MAC address of the WAN port of the router. You can check whether the MAC
clone configured in WAN Settings succeeded here.
12.10.3 LAN Status
This module enables you view the LAN IP address (the login IP address) of the router.
Parameter description:
Parameter
Description
IP Address
It specifies the LAN IP address of the router, which is the IP address used to log in to the web UI
of the router. You can log in to the web UI of the router through either IP address (default:
192.168.0.1) or the domain name (tendawifi.com).
Subnet
Mask
It specifies the subnet mask of the LAN IP address of the router.
MAC
Address
It specifies the MAC address of the LAN port of the router.
12.10.4 WiFi Status
This module allows you to view the WiFi status of the router, such as WiFi name, whether the WiFi network is
enabled or not. See the following figure:
137
Parameter description:
Parameter
Description
2.4 GHz/ 5
GHz Network
It specifies the WiFi status over 2.4 GHz/5 GHz network of the router.
- Disable: It indicates that the WiFi network is disabled.
- Visible: It indicates that the WiFi network is enabled and users can connect the Hotspot
Name of the WiFi network to access the internet.
Hotspot Name
It specifies the current WiFi name of the router. After the 2.4 GHz/5 GHz WiFi network is
enabled, smart devices can scan and connect to it to access the internet.
Encryption
Mode
It specifies the encryption mode of the WiFi network of the router.
WiFi Channel
It specifies the current wireless data transmission channel of the router.
WiFi
Bandwidth
It specifies the bandwidth of the operating channel of the router’s WiFi network, with a unit
MHz.
MAC Address
It specifies the MAC address of the WiFi network of the router.
12.11 System Log
This module enables you to view the system log information. The system logs can be used for troubleshooting
138
when the router is faulty.
To access the configuration page, click System Settings > System Log.
Clicking Export can export the system log to your local computer.
12.12 Automatic Maintenance
12.12.1 Overview
This module enables you to set the router to reboot at a specified time, improving the system stability and
service life of the router.
To access the configuration page, click System Settings > Automatic Maintenance. By default, the Automatic
Maintenance function is enabled.
139
Parameter description:
Parameter
Description
System
Reboot
Schedule
Used to enable or disable the system reboot schedule function.
Reboot At
It specifies the time for the router to reboot.
Delay
It specifies the premise for the router to delay a reboot.
- Selected: The router reboots automatically when there are devices connected to the
router, and the traffic over the WAN port is less than 3 KB/s for 30 minutes; or there are
no device connected to the router, and the traffic over the WAN port is less than 3 KB/s
for 3 minutes.
- Unselected: The router reboots automatically when the time for the router to reboot is up.
12.12.2 Configuring system reboot schedule
1. To access the configuration page, click System Settings > Automatic Maintenance.
2. Reboot At: Select the time to reboot from the drop-down list box, which is 23:30 in this example.
3. Click Save.
140
--End
After the configuration above, the router reboots automatically at 23:30 every day if there are devices connected
to the router, and the traffic over the WAN port is less than 3 KB/s for 30 minutes; or there are no devices
connected to the router, and the traffic over the WAN port is less than 3 KB/s for 3 minutes.
141
Appendixes
A.1 Setting the IP address of your computer
The following describes the configuration steps for Win8 and Win7. Choose the proper instructions according to
your computer system. A computer installed with a wired network adapter is used as an example here to
describe the procedures. Steps for configuring a computer installed with a wireless adapter are similar.
A.1.1 Windows 8
1. Right-click in the lower-right corner of the desktop and choose Open Network and Sharing Center.
2. Click Ethernet and Properties.
3. Double-click Internet Protocol Version 4 (TCP/IPv4).
142
4. Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK.
5. You are redirected to the Enternet Properties box, and click OK.
A.1.2 Windows 7
1. Right-click in the lower-right corner of the desktop and choose Open Network and Sharing Center.
143
2. Click Local Area Connection > Properties.
3. Double-click Internet Protocol Version 4 (TCP/IPv4).
144
4. Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK.
5. You are redirected to the Enternet Properties box, and click OK.
145
A.2 FAQ
Q1: I cannot access the web UI of the router after entering tendawifi.com or 192.168.0.1. What should I do?
A1: Try the following solutions and log in again:
- Ensure that your Ethernet cable with internet connectivity is plugged into the WAN port of the router
rather than a LAN port.
- Ensure that your wireless device is connected to the routers SSID.
- Ensure that your wired device is connected to port 1, 2 or 3 of the router properly by Ethernet cable.
And the device is also set to Obtain an IP address automatically and Obtain DNS server address
automatically.
- Ensure that tendawifi.com is entered correctly, or you can try logging by entering 192.168.0.1.
- Clear the cache of your web browser or replace the web browser, and try logging in again.
- Disable the firewall of your computer or replace the computer, and try logging in again.
- If the problem persists, reset your router and try logging in again.
Q2: How to choose my connection type?
A2: You can choose your internet connection type based on the following table or by consulting your internet
service provider (ISP).
Internet connection
media
Internet
connection type
Description
Telephone line/Ethernet
cable
PPPoE
You need to double-click and enter a PPPoE user name
and password to set up a dial-up connection.
TV cable/Ethernet cable
Dynamic IP
address
You can access the internet after connecting to an upstream
router or a cable TV.
Ethernet cable/Optical
fiber
Static IP address
You are assigned a static IP address, a subnet mask, a default
gateway address, and DNS server address for accessing the
internet.
Q3: I cannot access the internet after configuring internet settings. What should I do?
A3: Try the following solutions and log in again:
Log in to the web UI of the router, and check your routers connection status on the Internet Status page.
- If your router is connected to the internet successfully as the figure shown below, try the following
solutions:
146
Connect your wireless devices to the WiFi network of the router using the new WiFi name and password you set.
- If Connection failed appears on the page:
Click Internet Settings on the web UI to check whether the connection type and parameters you
entered are correct.
Connect the Ethernet cable with internet connectivity to your computer directly.
If your computer cannot access the internet, consult your ISP.
Otherwise, reconnect the Ethernet cable with internet connectivity to your router, reset your router and
configure it again.
Q4: How to reset the router if I cannot access the web UI of the router?
A4: Power on your router. When the SYS indicator blinks, hold down the RST/WPS button for about 8 seconds.
The router is reset successfully when all the LED indicators blink once.
Q5: An IP address conflict message appears after a computer which is connected to the router starts. What
should I do?
A5: Try checking the following items:
- Ensure that there is no other DHCP server in your LAN or the other DHCP server is disabled.
- Verify that the IP address of your router is not used by another device in your LAN. The default IP address of
the router is 192.168.0.1.
- Ensure that the static IP address assigned to the computer in your LAN is not used by other devices.
Connection type
Information provided by your ISP
PPPoE
ISP user name and ISP password
Dynamic IP address
None
Static IP address
IP address, subnet mask, gateway, DNS server and other
parameters
147
Q6: I forget the login password of the router. What should I do?
A6: Reset the router and log in the routers web UI.
Method to reset: Power on your router. When the SYS indicator blinks, hold down the RST/WPS button for
about 8 seconds. The router is reset successfully when all the LED indicators blink once
148
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
Operations in the 5.15-5.25 GHz band are restricted to indoor use only.
This equipment should be installed and operated with minimum distance 20 cm between the radiator &
your body.
The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use
a shielded RJ45 cable.
Declaration of Conformity
Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type AC10 is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.tendacn.com/en/service/download-cata-101.html
Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment type AC10U is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.tendacn.com/en/service/download-cata-101.html
Operate Frequency:
2.4 GHz: EU/2400-2483.5 MHz (CH1-CH13)
5 GHz: EU/5150-5250 MHz (CH36-CH48)
EIRP Power (Max.):
2.4 GHz: 19.95 dBm
5 GHz: 22.9 dBm
Software Version: V15.03.06
Caution(For AC10)
Adapter Model: BN036-A12012E
Manufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY Co., LTD.
Input: 100 - 240 V AC 50/60 Hz 0.4 A
Output: 12 V dc 1 A
: DC Voltage
Caution(For AC10U)
Adapter Model: BN037-A18012E
Manufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY Co., LTD.
Input: 100 - 240 V AC 50/60 Hz 0.6 A
149
Output: 12 V dc 1.5 A
: DC Voltage
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The device is for indoor usage only.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it
also complies with Part 15 of the FCC RF Rules.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use
a shielded RJ45 cable.
Operating Temperature: 0 °C - 40 °C
Operating Humidity: (10 90)% RH, non-condensing
150
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This
means that this product must be handled pursuant to European directive 2012/19/EU in order to be
recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he
buys new electrical or electronic equipment.
Copyright © 2018 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and
product names mentioned herein are trademarks or registered trademarks of their respective holders.
Specifications are subject to change without notice.
Technical Support
USA hotline: 1-800-570-5892
Toll Free: Daily-9am to 6pm EST
Canada hotline: 1-888-998-8966
Toll Free: Mon - Fri 9 am - 6 pm PST
Website: http://www.tendaus.com
Email: support.usa@tenda.com.cn
Hong Kong Hotline: 00852-81931998
Website: http://www.tendacn.com
E-mail: support@tenda.com.cn
BE BG CZ DK DE EE IE
EL ES FR HR IT CY LV
LT LU HU MT NL AT PL
PT RO SI SK FI SE UK
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tenda AC10U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tenda AC10U in the language / languages: English as an attachment in your email.

The manual is 5,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info