Manual Telwin STARTRONIC 530 (page 3 of 92) (All languages)

627245

Zoom out

Zoom in

1/92

The three LED's indicate the condition of the battery by to let the gas produced go out.

reading its voltage. The top LED indicates a charged - Check that the level of the electrolyte covers the plates of

battery, with a battery voltage reading greater than or the battery. If these were not covered add distilled water

equal to the voltage setting. The middle LED indicates that and cover them up to 5-10 mm.

_________________________________________________________________________________

the battery is able to receive more current and, lastly, the

bottom LED indicates that the battery is flat.

NOTE: for further details about the indicator see FIG. B

WARNING: USE THE MAXIMUM CAUTION

6-(DISPLAY) Current/Voltage/Time indicator :

DURING THIS OPERATION AS THE ELECTROLYTE IS A

This key can be used to select 3 different indicators:

HIGHLY CORROSIVE ACID.

- ”I”, displays the output current in Amps, in both

_________________________________________________________________________________

”CHARGE”, and “TRONIC” modes.

- ”V”, in this position the display shows the output voltage

- Please remember that the exact charge status of the

over the battery terminals in Volts.

battery can only be determined by using a densimeter

- ”TIME”, in this position the display indicates the length

which allows measurement of the specific gravity of the

of time that has elapsed during “CHARGE” mode, in

electrolyte the following indicate approximate density

minutes.

values for the solute (Kg/l at 20°c):

- The display also shows a set of letters representing the

1.28 = charged battery

current condition /mode (FIG. B).

1.21 = half-charged battery

- In “START-PAUSE” mode the display shows the time

1.14 = flat battery

_________________________________________________________________________________

remaining during the forced pause, in seconds.

7-Selecting Charging Time:

This key is used to select the charging time for the

WARNING: When handling the cables, make sure

“CHARGE” function; the following times are available:

that the “OFF” LED on the front panel is lit up.

2/4/6/10 hours.

_________________________________________________________________________________

In "CHARGE” mode, if the preset time passes before the

- Check the battery voltage and make sure that the settings

end-of-charge voltage is reached, the battery charger will

on the battery charger panel are compatible with the

automatically charge for 2 more hours and then switch off.

specifications for the battery being charged.

8-Potentiometer:

- Check the polarity of the battery terminals: positive for the

This potentiometer is used to set the charge current in

+ symbol and negative for the - symbol.

both "CHARGE" and “TRONIC” modes.

NOTE: if it is impossible to distinguish between the

9-(OFF) Switching off:

symbols, bear in mind that the positive terminal is the one

This key switches the current to the battery/ies ON or OFF.

that is not connected to the vehicle chassis.

WARNING: the battery charger is still powered even

- Connect the red charge clamp to the positive terminal of

when the OFF LED is lit.

the battery (+ symbol).

- Connect the black charge clamp to the vehicle chassis, far

5. INSTALLATION

away from the battery and from the fuel pipe.

SETTING UP (FIG. C)

NOTE: if the battery is not installed in the vehicle, connect

- Unpack the battery charger and assemble the separate

the black clamp directly to the negative terminal on the

parts included in the package.

battery (- symbol).

- Power the battery charger by inserting the power supply

POSITIONING THE BATTERY CHARGER

cable into the mains outlet.

- Position the battery charger for operation, making sure

Position the switch on the back to the ( I ) position.

that it is stable and that there is sufficient ventilation with

- Check the battery voltage and make sure that the settings

no obstructions to air passage through the vents provided

on the battery charger panel are compatible with the

for this purpose.

specifications for the battery being charged. These

- Install the battery charger on a horizontal surface with a

checks should be carried out with the corresponding key

solid base.

in "TEST" mode.

- Set an appropriate current value using the potentiometer

CONNECTION TO THE MAIN SUPPLY

on the front panel.

- The battery charger should be connected only and

exclusively to a power source with the neutral lead

CHARGING

connected to earth.

Press the corresponding key to pass to “CHARGE” mode.

Check that the mains voltage is the same as the voltage of

Position the battery charger to “ON” by pressing the

the equipment.

corresponding key on the front panel.

- Check that the power supply is protected by systems such

Monitor the battery voltage and charge current parameters

as fuses or automatic switches, sufficient to support the

on the display using the “V / I/ TIME” key (FIG.A-6).

maximum absorption of the equipment.

The ammeter will show the charge current (in amps) for the

- The connection to the main supply has to be made using a

battery: at the end of this phase you will see that the value

suitable cable.

shown on the ammeter will decrease slowly to very low

- If you put an extension to the primary cable, the section

values, according to the capacity of the battery and its

should be adequate and, in any case, never less than that

condition.

of the cable supplied.

- You always have to earth the equipment with the

AUTOMATIC CHARGING

yellow/green wire contained in the main cable, indicated

Press the corresponding key to pass to “TRONIC” mode.

by the label ( ), while the other two wires should be

Position the battery charger to “ON” by pressing the

connected to the mains.

corresponding key on the front panel.

During this phase the battery charger constantly monitors

6. OPERATION

the voltage over the battery terminals, automatically

BEFORE CHARGING

supplying or cutting off the charge current to the battery as

NB: Before charging check that the capacity of the

necessary.

battery (Ah) which is to be charged, is not inferior to that

Also in this case it is possible to monitor the battery voltage

reported on the data table. (C min).

and charge current on the display using the “V / I / TIME” key.

Follow the instructions, taking great care to respect the

The charge current can be set as illustrated. When it is cut off

order given below.

the display will show the message “END”.

- Remove the caps of the battery charger (if foreseen) so as

- 3 -

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Telwin STARTRONIC 530 in the language / languages: All languages as an attachment in your email.

The manual is 1,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Telwin STARTRONIC 530 Manual

Product: