Manual Telwin STARTRONIC 500 (page 9 of 44) (All languages)

627243

Zoom out

Zoom in

1/44

MAIN SPECIFICATIONS

enabling the CHARGE+STD BY function.

The CHARGE function permits initial charging of the battery

at constant current with the value previously set, for a time

selected via the key (D). If the battery voltage is particularly

low, a very small current will be delivered until 1.5 V/e is

reached; once this threshold has been reached the ST500

will set its current until the end-of-charge limits for that

particular type of battery are reached. Once this time has

elapsed, if the battery has not reached a certain battery

voltage level (stored inside the microcontroller) a further 2

hours are added after which the battery charge is switched

off. If the battery charger reaches the reference voltage

before the end of the set time the battery charger switches

off without adding the extra two hours.

The START function permits starts at CONSTANT

VOLTAGE, automatically limiting the current to the pre-set

values with cycles lasting "5 sec ON" and "20 sec OFF".

Blinking of the START led indicates that this function is

enabled.

(D) Charge Time Selection Key

This key permits selection of the charge time for the

CHARGE function. The following times are possible:

2/4/6/10 hours.

(CHARGE) Charge Current Selection Key

Selecting the Charge Current:

This key is used to select the charge current level in

FRONT PANEL KEYS

"CHARGE" mode .

The charge currents that can be set are 2/5/10/20/30/40 A.

By setting the key to START, the current available is 300 A

FIG. B

minimum.

(A) Battery Type Selection Key

(DISPLAY) Current/Voltage/Time Indication Key

In this case it is possible to select the type of battery to be

Three different displays can be selected with this key:

charged. This selection automatically modifies the battery

- "I": the current delivered in Amps is displayed, both in

voltage thresholds when switching from constant current to

charge and start;

constant voltage occurs.

- "V": in this position the display indicates the output voltage

The types of battery that can be selected are:

to the battery in Volts;

“GEL”: lead-acid batteries with solid electrolyte (2.3

- "TIME": in this position the display indicates the amount of

V/element)

time elapsed during the charge function in hours and

“WET”: lead-acid batteries with liquid electrolyte (2.4

minutes.

V/element)

“Ni-Cd”: nickel-cadmium batteries (1.4 V/element)

WARNING:

For the nickel-cadmium batteries, the correct number

FIG.C

of elements for the three charge voltages are:

5 elements for 6V batteries

(A) Battery Voltage Selection Key

10 elements for 12V batteries

This key permits selection of the battery voltage. The

20 elements for 24V batteries (assuming 1.4V/e)

scheduled working voltages are 12/24 V.

(B) Battery Voltage Selection Key

(B) Operating Mode Selection Key

This key permits selection of the battery voltage. The

Whenever this key is pressed and the stand-by plug is

scheduled working voltages are 6/12/24 V.

connected, one of the following 3 operating modes is

selected:

STAND BY/CHARGE/START:

Whenever this key is pressed, one of the following 3

Selection is performed by pressing the various buttons until

operating modes is selected:

the led corresponding to the required mode or setting

STAND-BY & CHARGE / CHARGE / START

comes on; a buzzer indicates that the setting has been

Selection is performed by pressing the various buttons until

performed.

the led corresponding to the required mode or setting

The STAND-BY function offers a 12Vdc-1.5A

comes on; a buzzer indicates that the setting has been

When the plug of the STAND-BY connector is inserted in the

performed.

cigar-lighter outlet the respective LED lights up and the

The STAND-BY function offers a 12Vdc-1.5A stabilised

vehicle's essential services will receive power.

power supply output which powers the essential vehicle

This function powers the essential vehicle functions via the

functions via the cigar lighter socket. This function can also

cigar lighter socket, It can also be performed at the same

be performed at the same time as battery charging by

time as battery charging by enabling the CHARGE

OPERATION STAND-BY

FIG. A

With the standby function (A) the essential electronic

services of the vehicle can be powered using the auxiliary

cable inserted in the cigar-lighter socket. When the auxiliary

cable connector is connected to the Startronic the red

standby LED lights up: the power supply output is 12Vdc-

1,5A.

ST 500

ST 300

- 9 -

Bom dia;
existe manual electronico para o carregador de baterias startronic 500 da telwin? Submitted on 14-3-2022 at 12:47
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Telwin STARTRONIC 500 in the language / languages: All languages as an attachment in your email.

The manual is 1,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Telwin STARTRONIC 500 Manual

Product: