Manual Telwin PRO START 1712 (page 4 of 68) (All languages)

649703

Zoom out

Zoom in

1/68

the negative terminal of the battery.

ATTENTION:DANGER!

If the warning light comes on (Fig. A-1) and

the buzzer sounds this means “REVERSE

POLARITY”, DANGER!

In these circumstances NEVER switch on the vehicle,

and remove the cables immediately!

Make sure the vehicle battery and starter battery

polarities are correct before making the connections

described above.

- Position the starter’s switch at ON: this can be done by

pressing it and then rotating it clockwise by 90° (FIG.

A-2).

- Turn the ignition switch or key of the vehicle or boat to

ON. Wait about one minute. Turn the vehicle ignition to

the start position for no more than 3÷4 seconds. If the

vehicle or boat does not start, wait at least 3 minutes

before trying again.

Careful: Always stop the black and red

clamps from touching each other or a

common cable.

Follow the sequence of instructions scrupulously while

the engine is running.

1. Switch off the starter: switch positioned at “OFF”.

2. Disconnect the black clamp (negative) from the vehicle.

3. Disconnect the red clamp (positive) from the vehicle.

4. Return the clamps to their correct seat.

It is highly recommended to recharge the starter as soon

as possible.

Usingthestarterasa12VDCpowersupply:

- Take the cover off the cigar-lighter type socket (Fig.

A-3).

- Insert the cigar-lighter plug of the device to be powered

into the socket (Fig. A-3).

Usingthestarterasa5VDCpowersupply:

- Raise the USB port cover (Fig. A-4).

- Insert the USB cable of the device to be powered into

the socket (Fig. A-4).

- Press the button seen in Fig. A-5: the led seen in Fig.

A-6 will light up to indicate the USB port is in use.

Attention: never connect this USB port

directly to a USB port on a computer: this

could seriously damage both devices!

UsingreectorswithashingLED’s:

In the event of an emergency, it is possible to place the

starter on the roadside and activate the reectors with

ashing LED’s by pressing the button seen in Fig. A-7.

UsingtheLEDlamp:

The LED lamp is magnetically attached to the starter

(Fig. A-9). You can remove the lamp to use it, simply

grasp it with your hand and pull it towards you. The lamp

has a rechargeable battery: the lamp is automatically

recharged when placed in its housing on the starter with

the switch turned to the OFF position/

RECHARGING

Important! To protect the battery and lengthen its

working life, charge it for 12 hours before using it for

thersttime,thenaftereverytimeitisusedand,in

any case, at least every 3 months.

The unit can be recharged using a 230V AC power supply

(using the power supply adapter supplied) or using a 12V

DC power supply. We recommend keeping the battery

fully charged at all times. A low charge level could shorten

the life of the battery. Bear in mind that the time needed

to recharge the battery depends on the number of times it

has been used as a starter. To check whether the battery

needs recharging, press the switch seen in g.A-10.

The three LED’ps seen in Fig. A-13 indicate the charge

status of the battery, with the following meanings:

: the battery is very at;

: the battery is at;

: the battery is fully charged.

The red “Charging” LED (Fig. A-11) will light up when unit

is being charged.

The green “Remove Charger” LED (Fig. A-12) will light

up when the unit is being charged to indicate that the

control device that protects the adaptor or battery has

been triggered. It is recommended to disconnect the

adaptor jack from the recharger socket.

Recharging using a 230V AC power supply

ATTENTION:Usethesuppliedpowersupply

adapter only!

1- To start with, insert the power supply adaptor plug

(Fig. B-1) into a 230V AC socket.

Then insert the relative output plug (Fig. B-2) into the

charger socket (Fig. A-8).

2- The “Charging” LED comes on and the starter is in

recharge mode. The starter is tted with a control

device to prevent overcharging the battery and

adaptor. Leave the system to recharge for as long as

necessary.

N.B.: to check the battery level disconnect the

adaptorandpressthebuttonseeninFig.A-10:The

LED’s seen in Fig. A-13 indicate the charge status of

the battery, with the meanings indicated above.

Recharging onboard the vehicle using 12V DC power

supply:

ATTENTION:Recharge the batterywhenthe

vehicle is running.

1- Insert the cigar-lighter plug of the supplied cable

(Fig. B-3) into the socket onboard the car or boat.

2- Insert the jack (Fig. B-4) of the supplied cable into

the recharger socket on the starter (Fig. A-8).

NOTE: this function is used to keep the charge level of

the starter as high as possible whilst travelling and may

not allow complete recharging.

DISPOSING OF THE BATTERY

When the starter battery is completely run down it should

taken be to a re-cycling depot. In some countries this is

mandatory. Contact the local special refuse authority for

information on recycling.

WARNING: Do not burn the battery to dispose of it.

This could cause an explosion. Before disposing of the

battery, apply insulating tape to the bare terminals to

prevent shorting. Do not expose the battery to intense

heat or re as this could cause an explosion.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Telwin PRO START 1712 in the language / languages: All languages as an attachment in your email.

The manual is 1,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Telwin PRO START 1712

Telwin PRO START 1712 User Manual - All languages - 60 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Telwin PRO START 1712 Manual

Product: