627123

Telwin NORDICA 4.220 TURBO Manual

7
Zoom out
Zoom in
Previous page
1/88
Next page
- 7 -
Connecting the electrode-holder clamp welding cable
On the end take a special terminal that is used to close the uncovered
part of the electrode.
For welding machines supplied with a terminal, this cable is connected to
the terminal with the symbol
.
Connecting the welding current return cable
This is connected to the piece being welded or to the metal bench
supporting it, as close as possible to the join being made. For welding
machines supplied with a terminal, the cable is connected to the terminal
with the symbol
.
Recommendations:
- Screw the welding cable connectors right down into the quick
couplings (if present), so as to ensure perfect electrical contact;
otherwise, the connectors will overheat, wear rapidly and become
inecient.
- Use welding cables that are as short as possible.
- Do not use metal structures that are not part of the workpiece to
substitute the welding current return cable; this could endanger safety
and produce an unsatisfactory weld.
6. WELDING: DESCRIPTION OF THE PROCEDURE
These welding machines consist of a drooping specication, single phase
transformer and are suitable for welding with alternating current using
coated electrodes (E 43 R type) based on the diameters given on the data
plate.
To switch on the welding machine operate the main switch (Fig. B-1).
The intensity of the supplied welding current can be adjusted
continuously, by means of a manually operated magnetic shunt (Fig. B-2),
or step-by-step by means of a manually operated switch (Fig. B-3).
CHECK THE WELDING MACHINE MODEL.
N.B. In the case of a welding machine with switch, current adjustment
should be carried out with the main switch (Fig. B-1) in the O position
(o).
The value of the current setting, (I
2
) can be read in Amps on the graduated
scale (Fig. B-4) on the top or side panel of machines where it is provided.
THERMOSTATIC PROTECTION
This welder is automatically protected from thermic overheating
(thermostat automatic re-start). When the windings reach performance
temperature, the protections cut o the supply circuit, igniting the
yellow lamp on the front panel (Fig. B-5). After a few minutes’ cooling the
protection will reopen the supply line and turn o the yellow lamp. The
welder is ready for further use.
WELDING
- Use electrodes suitable for working in alternating current.
- The welding current must be regulated according to the diameter of
the electrode in use and the type of the joint to be carried out: see
below the currents corresponding to various electrode diameters:
Ø Electrode (mm)
Welding current (A)
min. max.
1.6 25 50
2 40 80
2.5 60 110
3.2 80 160
4 120 200
- The user must consider that, according to the electrode diameter,
higher current values must be used for at welding, whereas for vertical
or overhead welds lower current values are necessary.
- In addition to being determined by the selected current intensity, the
mechanical characteristics of the welded join are determined by the
other welding parameters i.e. arc length, working rate and position,
electrode diameter and quality (to store the electrodes correctly keep
them dry and protected by suitable packaging or containers).
Welding procedure
- Holding the mask IN FRONT OF THE FACE, strike the electrode tip on the
workpiece as if you were striking a match. This is the correct strike-up
method.
WARNING: do not hit the electrode on the workpiece, this could
damage the electrode and make strike-up dicult.
- As soon as arc is ignited, try to maintain a distance from the workpiece
equal to the diameter of the electrode in use. Keep this distance as
much constant as possible for the duration of the weld. Remember
that the angle of the electrode as it advances should be of 20-30 grades
(Fig. H).
- At the end of the weld bead, bring the end of the electrode backward,
in order to ll the weld crater, quickly lift the electrode from the weld
pool to extinguish the arc.
CHARACTERISTICS OF THE WELD BEAD
Fig. I
7. MAINTENANCE
WARNING! BEFORE CARRYING OUT MAINTENANCE
OPERATIONS MAKE SURE THE WELDING MACHINE IS SWITCHED OFF
AND DISCONNECTED FROM THE MAIN POWER SUPPLY.
EXTRAORDINARY MAINTENANCE
EXTRAORDINARY MAINTENANCE MUST ONLY BE CARRIED OUT BY
TECHNICIANS WHO ARE EXPERT OR QUALIFIED IN THE ELECTRIC-
MECHANICAL FIELD, AND IN FULL RESPECT OF THE IEC/EN 60974-4
TECHNICAL DIRECTIVE.
WARNING! BEFORE REMOVING THE WELDING MACHINE
PANELS AND WORKING INSIDE THE MACHINE MAKE SURE THE
WELDING MACHINE IS SWITCHED OFF AND DISCONNECTED FROM
THE MAIN POWER SUPPLY OUTLET.
If checks are made inside the welding machine while it is live, this
may cause serious electric shock due to direct contact with live parts
and/or injury due to direct contact with moving parts.
- Inspect the welding machine regularly, with a frequency depending
on use and the dustiness of the environment, and remove the dust
deposited on the transformer, using a jet of dry compressed air (max.
10 bar).
- At the same time make sure the electrical connections are tight and
check the wiring for damage to the insulation.
- At the end of these operations re-assemble the panels of the welding
machine and screw the fastening screws right down.
- Never, ever carry out welding operations while the welding machine is
open.
- If necessary use a very thin layer of grease, at a high temperature, to
lubricate the moving parts of the regulators (threaded shaft, sliding
surfaces, shunts etc.).
- Replacing the power supply cable: before replacing the cable,
identify the screw-connecting terminals L1 and L2 (N) on the switches
(Fig. L).
- After having carried out maintenance or repairs, restore the connections
and wiring as they were before, making sure they do not come into
contact with moving parts or parts that can reach high temperatures.
Tie all the wires as they were before, being careful to keep the high
voltage connections of the primary transformer separate from the low
voltage ones of the secondary transformer.
Use all the original washers and screws when closing the casing.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telwin NORDICA 4.220 TURBO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telwin NORDICA 4.220 TURBO in the language / languages: All languages as an attachment in your email.

The manual is 4,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info