627188

Telwin MAGNUM 400 CE Manual

8
Zoom out
Zoom in
Previous page
1/20
Next page
- 8 -
INTERNAL COMBUSTION ENGINE MAINTENANCE
Carry out the checks and programmed maintenance indicated in
the USER MANUAL of the internal combustion engine producer.
The discharge pump (Fig. N) can be used to change the oil.
EXTRAORDINARY MAINTENANCE
EXTRAORDINARY MAINTENANCE MUST ONLY BE CARRIED
OUT BYTECHNICIANS WHOARE EXPERT OR QUALIFIED IN
THE ELECTRIC-MECHANICAL FIELD, AND IN FULL RESPECT
OFTHEIEC/EN60974-4TECHNICALDIRECTIVE.
WARNING!BEFOREREMOVINGTHEENGINE-DRIVEN
WELDINGMACHINEPANELSANDACCESSINGIT,MAKESURE
ITISSWITCHEDOFF.
Ifchecksarecarriedoutwhiletheinsideoftheengine-driven
weldingmachineislivethiscouldcauseseriouselectricshock
duetodirectcontactwithlivepartsand/orinjuryduetodirect
contactwithmovingparts.
- Make regular checks at intervals that depend on the use and on the
amount of dust in the environment, inspecting inside the engine-
driven welding machine and removing any dust deposited on the
alternator and on the reactance coil using a jet of dry compressed
air (max. 10bar).
- Take the opportunity to make sure there are no loose electrical
connections and that the wiring insulation has not been damaged.
- After completing these operations, re-assemble the engine-driven
welding machine panels, tightly fastening the screws.
- Never ever carry out welding operations if the engine-driven
welding machine is open.
- After having carried out maintenance or repairs, restore the
connections and wiring as they were before, making sure they do
not come into contact with moving parts or parts that can reach
high temperatures. Tie all the wires as they were before, being
careful to keep the primary high voltage connections separate from
the secondary low voltage ones.
Use all the original washers and screws when re-closing the
structural work.
9. ENGINE-DRIVEN WELDING MACHINE TRANSPORT AND
WINTERSTORAGE
Regarding engine-driven welding machine transport and winter
maintenance, refer to the USER MANUAL of the internal combustion
engine producer.
10.TROUBLESHOOTING
IF THE WELDING MACHINE IS NOT WORKING PROPERLY,
BEFORE MAKING MORE SYSTEMATIC CHECKS OR CALLING
YOUR SERVICING CENTRE MAKE THAT:
- The welding current is suitable for the diameter and type of
electrode to be used.
- You have not exceeded the rated duty cycle; if the thermal cutout
has triggered wait until the engine-driven welding machine has
cooled naturally, make sure the fan is working properly.
- There is no shorting at engine-driven welding machine output: in
such a case eliminate the problem.
- The welding circuit connections have been made correctly, in
particular that the earth clamp is actually connected to the piece,
with no insulating material (e.g. paint) in the way.
As far as troubleshooting for the engine is concerned, refer to
the USER MANUAL of the internal combustion engine producer.
Refer to the nearest engine retailer should problems with the
internal combustion engine occur.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telwin MAGNUM 400 CE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telwin MAGNUM 400 CE in the language / languages: All languages as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info