627232

Telwin LEADER 220 START Manual

2
Zoom out
Zoom in
Previous page
1/60
Next page
protected against indirect contacts by an earth lead as
_____________( GB )______________
required for class I equipment.
INSTRUCTION MANUAL
3. INSTALLATION
ASSEMBLY (FIG.A)
- Unpack the battery charger and assemble the separate
parts contained in the package.
- Models on wheels are to be set in a vertical position.
WARNING: BEFORE USING THE BATTERY CHARGER
POSITIONING THE BATTERY CHARGER
READ THE INSTRUCTION MANUAL CAREFULLY.
- During operation, position the battery charger on a stable
surface and make sure that there is no obstruction to air
1. GENERAL SAFETY RULES WHEN USING THIS
passage through the openings provided to ensure
BATTERY CHARGER
sufficient ventilation.
CONNECTION TO THE MAIN SUPPLY
- The battery charger should be connected only and
- During the charge the battery produces explosive gases,
exclusively to a power source with the neutral lead
avoid the formation of flames and sparkes. DO NOT
connected to earth.
SMOKE.
Check that the mains voltage is the same as the voltage of
- Position the batteries to be charged in a well-ventilated
the equipment.
place.
- Check that the power supply is protected by systems such
as fuses or automatic switches, sufficient to support the
maximum absorption of the equipment.
- The connection to the main supply has to be made using a
suitable cable.
- Inexperience and untrained people should be
- If you put an extension to the primary cable, the section
properly instructed before using the appliance.
should be adequate and, in any case, never less than that
- People (children included) whose physical, sensory
of the cable supplied.
or mental capacities would prevent them from using
- You always have to earth the equipment with the
the appliance correctly must be supervised by a
yellow/green wire contained in the main cable, indicated
person who is responsible for their safety while the
by the label ( ), while the other two wires should be
W
appliance is in use.
connected to the mains.
- Children must be supervised to ensure that they do
not play with the appliance.
4. OPERATION
- Use the battery charger only indoors and make sure that
BEFORE CHARGING
you start it in airy places. DO NOT SET IN THE RAIN OR
NB: Before charging check that the capacity of the
SNOW.
battery (Ah) which is to be charged, is not inferior to that
- Disconnect the mains cable before connecting to or
reported on the data table. (C min).
disconnecting the charging cables from the battery.
Follow the instructions, taking great care to respect the
- Do not connect or disconnect the clamps to or from the
order given below.
battery with the battery charger operating.
- Remove the caps of the battery charger (if foreseen) so as
- Never use the battery charger inside the car or in the
to let the gas produced go out.
bonnet.
- Check that the level of the electrolyte covers the plates of
- Substitute the mains cable only with an original one.
the battery. If these were not covered add distilled water
- Do not use the battery charger to charge batteries which
and cover them up to 5-10 mm.
are not rechargeable.
- Make sure the available power supply voltage
WARNING: USE THE MAXIMUM CAUTION DURING
corresponds to that shown on the battery charger rating
THIS OPERATION AS THE ELECTROLYTE IS A HIGHLY
plate.
CORROSIVE ACID.
- To avoid damaging the vehicle's electronics, read, keep
- Please remember that the exact charge status of the
and take very careful note of the information supplied by
battery can only be determined by using a densimeter
the vehicle manufacturer, when using the battery charger
which allows measurement of the specific gravity of the
either for charging or starting; the same applies to the
electrolyte the following indicate approximate density
instructions supplied by the battery manufacturer.
values for the solute (Kg/l at 20°c):
- This battery charger has components such as switches
1.28 = charged battery
and relays which can cause arcs or sparks. Therefore
1.21 = half-charged battery
when using it in a garage or in a similar place set the
1.14 = flat battery
battery charger in a suitable case.
- With the power supply cable disconnected from the main
- Repair or maintenance of the inside of the battery charger
power supply outlet, position the 6/12 V or 12/24 V switch
can be executed only by skilled technicians.
(if present) according to the rated voltage of the battery to
- WARNING: ALWAYS DISCONNECT THE POWER
be charged.
SUPPLY CABLE FROM THE MAINS BEFORE
- Position the switch/es for adjusting the type of charge (if
CARRYING OUT ANY SIMPLE MAINTENANCE
present) as required (FIG.B. LOW normal charging,
OPERATION ON THE BATTERY CHARGER.
HIGH rapid charging).
- Make sure the power outlet is protected by an earth
- Check the polarities of the battery terminals: positive for
connection.
the + symbol and negative for the - symbol.
- For those models without one, connect a plug with
NOTE: if the symbols are indistinguishable remember
suitable capacity in relation to the fuse size shown on the
that the positive terminal is the one not connected to the
data plate.
vehicle chassis.
- Connect the red charge clamp to the positive terminal of
2. INTRODUCTION AND GENERAL DESCRIPTION
the battery ( + symbol).
- This battery charger can be used to charge free
- Connect the black charge clamp to the vehicle chassis, at
electrolyte lead acid batteries used on petrol and diesel
a safe distance from the battery and the fuel pipe.
engine vehicles, motor cycles, boats etc.
NOTE: if the battery is not installed in the vehicle, connect
- The charging current delivered by the battery decreases
the clamp directly to the negative terminal of the battery (-
according to the characteristic W bend - see the DIN
symbol).
41774 norm.
- The charger case has a protection degree of IP 20 and is
- 2 -
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telwin LEADER 220 START at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telwin LEADER 220 START in the language / languages: All languages as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info