Manual Telwin ALPINE 30 BOOST (page 5 of 64) (All languages)

627102

Zoom out

Zoom in

1/64

- 5 -





When recharging a WET-type battery, proceed as follows:

- Remove the caps of the battery charger (if foreseen) so as to let the

gas produced go out. Check that the level of the electrolyte covers

the plates of the battery. If these were not covered add distilled

water and cover them up to 5-10 mm.

WARNING: USE THE MAXIMUM CAUTION DURING

THIS OPERATION AS THE ELECTROLYTE IS A HIGHLY





- Make sure the power cable is disconnected from the mains.

- With models having more than one charge voltage, turn the

deviator or the switch to the selected charge voltage. If there is

no deviator or switch, suitably connect the red crocodile clip (+

symbol) to the specic battery charger terminal in correspondence

with the selected charge voltage.

- Connect the red charge clamp to the positive terminal of the battery

( + symbol). If the symbols are indistinguishable remember that the

positive terminal is the one not connected to the vehicle chassis.

- Connect the black charge clamp to the vehicle chassis, at a safe

distance from the battery and the fuel pipe.

NOTE: if the battery is not installed in the vehicle, connect the clamp

directly to the negative terminal of the battery (- symbol).



NOTE: the Ah values, if given beside the pushbuttons, are purely

indicative (because the charging process depends on how at the

battery is) and they suggest the position for charging an initially at

battery with capacity within the indicated range, in under 15 hours. It

is not advisable to go below the minimum values that are indicated.



)

Recommended method for free electrolyte lead acid batteries (WET).

- Carefully follow the instructions given in paragraphs 6.1 and 6.2.

- Move the deviator (if present) to the BATTERY symbol.

- Turn the charge adjustment deviator/deviators or switch (if present)

(FIG. C) the normal charge position (BATTERY symbol) or fast

charge position (BOOST) as required (with some models the

switch also acts as a power switch).

- If the battery charger has a TIMER a maximum pre-set charge time

can be set (FIG. C).

- Power the battery charger by inserting the power supply cable into

the power outlet and turning the switch (if present) to ON.

- Monitor the ammeter as described in paragraph 4.

NOTE: Once the WET battery is charged, you may note the liquid

inside starting to “boil”. It is advisable to stop charging when this

phenomenon appears so as to prevent damage to the battery.



We recommend using models with the TRONIC mode to charge

sealed batteries (GEL, AGM).

- Carefully follow the instructions given in paragraphs 6.1 and 6.2.

- Turn the deviator to TRONIC and the charge adjustment switch

to the normal charge position (BATTERY symbol) or fast charge

position (BOOST) as required (FIG. C).

- Power the battery charger by inserting the power cable into the

mains socket. The battery charger controls the voltage present at

the battery terminals, automatically interrupting the current being

supplied when the battery is charged (the ammeter indicator

positions itself at zero) and supplying it again automatically when

the battery begins running down. The TRONIC mode is ideal for

automatically maintaining the battery charged (AGM and WET)

without the risk of damaging it.



       

        

    





For “parallel” connection batteries must have the same nominal

voltage (Volt), which corresponds to the battery charger output

voltage, and the total of Ah must be within the charge range of the

battery charger.

For “serial” connection batteries must have the same capacity

(Ah) and the sum of the nominal voltages of all the batteries must

correspond to the battery charger output voltage.



- Remove the power supply from the battery charger by turning the

switch to OFF (if present) and/or removing the power supply cable

from the mains outlet.

- Disconnect the black charge clamp from the chassis of the vehicle

or from the negative terminal of the battery (- symbol).

- Disconnect the red charge clamp from the positive terminal of the

battery (+ symbol).

- Store the battery charger in a dry place.

- Close up the battery cells with the appropriate plugs (if present).



      

manufacturer’s instructions carefully!

- Make sure the power line is protected by fuses or automatic

circuit-breakers with sizes as indicated on the rating plate by the (

) symbol.

- To make starting easier, quickly charge for 10-15 minutes at the

BOOST/BOOST&GO position (see paragraph 6.3.1).

- In order to prevent overheating in the battery charger, ALWAYS

carry out the starting operation according to the duty cycle (work/

pause) as indicated on the appliance (e.g. START 3s ON 120s

OFF-5 CYCLES). Do not insist if the engine does not start: this

could cause serious damage to the battery or even to the electrical

equipment in the vehicle. If the engine does not start, wait a few

minutes and then repeat the rapid charge operation.



- With the power cable disconnected from the mains, if necessary,

turn the deviator to 12V or 24V or suitably connect the red crocodile

clip to the specic battery charger terminal, according to the

nominal voltage of the battery of the vehicle to be started.

- Make sure the battery is connected properly to the respective (+

and -) terminals, and that it is in good condition (not sulphated or

dud). Never ever start vehicles with the batteries disconnected

from their respective terminals; the presence of the battery is

essential for the elimination of possible overvoltage.



- With the battery charger at OFF, plug in the power cable.

- Turn the switch, if present, to ON.

- Turn the switch to START and turn the ignition key to start up the

engine.



- Turn the switch to BOOST&GO.

- Power the battery charger by inserting the power cable into the

mains socket.

- Start up the vehicle by turning the ignition key.



- Disconnect the power to the battery charger by turning the switch

(if present) to OFF and remove the power cable from the mains.

- Disconnect the black crocodile clip from the negative battery

terminal (- symbol) and the red crocodile clip from the positive

battery terminal (+ symbol).

- Store the battery charger in a dry place.



The battery charger protects itself from:

- Overcharge (too much current supplied to the battery).

- Short-circuit (loading clips placed in contact with each other).

- Polarity inversion on the battery clamps.

For appliances tted with fuses, if the fuses have to be replaced

always use the same kind of fuse with the same rated size.

WARNING: If the replacement fuse has a different size from that

shown on the rating plate it could cause damage to people or

property. For the same reason, never ever replace the fuse with a

bridge in copper or other material.

The power supply cable should always be DISCONNECTED from the

mains supply while the fuse is being changed.

When replacing the ribbon fuse, if present, carefully fasten the nuts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Telwin ALPINE 30 BOOST in the language / languages: All languages as an attachment in your email.

The manual is 2,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Telwin ALPINE 30 BOOST Manual

Product: