628341
3
Zoom out
Zoom in
Previous page
1/15
Next page
4
5
Getting started
Location
You need to place your Telstra 6100/6100a close enough to a mains power and telephone socket so that
the cables will reach. Make sure it is at least 1 metre away from other electrical appliances to avoid
interference.
WARNING Do not place your Telstra 6100a in the bathroom or other humid areas.
Your Telstra 6100/6100a works by sending radio signals between the handset and base. The strength of
the signal depends on where you site the base. Putting it as high as possible can help to provide the best
signal
Handset range The handset reception range from the base is up to 300m outdoors and up to 50m indoors.
Thick walls can severely affect the range.
Range indicator The symbol on your handset display indicates when you are in range of the base. If the
symbol flashes and you hear a warning beep, you are out of range and will need to move closer to the base.
Setting up
1. Plug the mains power cable into the base. Then plug the power adaptor into the mains wall socket
and switch the power on. The light on the base lights up.
IMPORTANT Do not connect the telephone line until the handset(s) is fully charged. The base must be plugged
into the mains power at all times.
Which socket? Power socket Telephone line socket
Getting started
2. Remove the battery compartment cover and insert the 2 x AAA NiMH batteries supplied into the
handset. Slide the battery compartment cover back into place.
3. Charge the handset for at least 16 hours by placing it on the base. The charging indicator light on
the base comes on. The screen will show the standby display and a scrolling battery icon to show
that the handset is charging.
4. After 16 hours, plug the telephone line cord into your Telstra6100/6100a base unit and the other end
into the wall socket.
6SXO-Y\N
Your Telstra 6100/6100a is now ready for use.
Battery performance When batteries are fully charged the display shows the battery is full. To keep your batteries
in the best conditions, leave the handset off the base for a few hours at a time (after the initial 16 hour charge).
Please note however, that new NiMH batteries do not reach full capacity until they have been in normal use for
several days. Running the batteries right down at least once a week will help them last as long as possible. The
charge capacity of rechargeable batteries will reduce with time as they wear out, so reducing the talk/standby
time of the handset. Eventually they will need to be replaced. New batteries can be obtained from TecHelp on
1300 369 193 or your local electrical retailer.
Battery low warning When the battery charge is low the handset battery icon will show empty.
Place the handset back on the base to recharge.
Replacing batteries Use only rechargeable 750mAh or higher AAA NiMH batteries.
Talk/Standby time Under ideal conditions, fully charged handset batteries should give up to 10 hours
talk time or 100 hours standby on a single charge.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telstra 6100A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telstra 6100A in the language / languages: English as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info