14
Programming your modes
Note:
you can dedicate any appliance (TV, DVD, SAT...) to the SAT, DVD, VCR, CBL, AMP and
AUX (1 and 2) modes: you just need to enter
the 4 digit code (found in the code list) of the
appliance. In any case, please follow the steps below:
1. Make sure your equipment is switched on (for example TV).
2. Press and hold the Setup (19) key until the red indicator (13) lights continuously. Release the
Setup key.
3. Press and release the Mode key (1) of the device you want to control (for example TV). The
red indicator blinks once.
4. Using the numeric keypad (3), enter the 4 digit code from the Code List. The red indicator (13)
turns off after the last digit is entered. If you entered a wrong code the red indicator (13)
blinks for 3 seconds and then goes off. You have to repeat from step 2.
5.
Point the remote in the direction of your TV and press the Power button (2). Your device should
turn off. Check other functions (for example for a DVD: ̈ (Play) or ̈̈ (Fast Forward), etc.).
If certain functions are not responding this indicates that the entered code is not the correct
one. In that case repeat the above procedure with the next corresponding code of your brand.
6. Repeat this procedure from step 1 for the other equipment you want to control.
Manual code search
If your equipment (TV, SAT etc....) does not respond, try the other codes for your brand. If it still
doesn’t respond, try the Code Search method.
Note:
as you can dedicate any appliance (TV, DVD, SAT...) to the SAT, DVD, VCR, CBL, AMP and
AUX (1 and 2) modes, you need first to enter any 4 digit code for the kind of appliance you wish
to control (found in the code book), i.e.: If you want to program a DVD under the SAT key, enter
any DVD code found in the code list and then follow the steps below:
1. Make sure your equipment is switched on. If not switch it on manually.
2. Press and hold the Setup (19) key until the red indicator (13) lights continuously. Release the
Setup key.
3. Press the Mode key (1) that matches the equipment you want to control (for example TV). The
red indicator blinks once.
4. Point the remote control at the device you wish to control and press CH+ (10) repeatedly until
the channel changes. If you step pass the correct code use CH- (10) to go back to the right
code. Each time you press the CH+ (or CH-), the red indicator will blink.
5. When the equipment you want to control reacts press OK (11) to confirm the code.
Note:
If your equipment doesn't have CH+, you can use Power (2) or Play (VCR or DVD only)
(17) key.
If all codes have been searched, the red LED indicator will blink for about 3 seconds.
Note:
if certain functions of your equipment can’t be controlled you have to find a different code
for your brand.
Automatic code search
When searching an unknown code, you can step through the library automatically (AutoSearch).
When your equipment responds, you can stop the searching process and store the code you found.
Note:
as you can dedicate any appliance (TV, DVD, SAT...) to the SAT, DVD, VCR, CBL, AMP and
AUX (1 and 2) modes, you need first to enter any 4 digit code for the kind of appliance you wish
to control (found in the code book), i.e.: If you want to program a DVD under the SAT key, enter
any DVD code found in the code list and then follow the steps below:
1. Turn on the device you want to control.
2. Press and hold the Setup (19) key until the red indicator (13) lights continuously. Release the
Setup key.
3. Press the Mode key (1) that matches the equipment you wish to control. The red indicator (13)
blinks once.
4. Point the remote control at the device you wish to control and press the CH+ (10) once. If the
device does not possess a channel up function, then press the ►Play (DVD/VCR only) (17) or
Power (2) key instead of CH+. After a few seconds the remote starts stepping through the
code library (fast search, 1 code per second). You can press CH+ (10) a second time to switch
to slow search (1 code per 3 seconds). Each time a code is sent, the red indicator will blink off.
5. As soon as the device does respond to the remote control, press OK (11) to store the code
you found.
6. If accidentally you miss the code, you can stop the autosearch by pressing CH- (10) and by
repeatedly pressing this key return to the right code (you can step forward by pressing CH+
(10) in case you went too far back).
If all codes have been searched, the red indicator will blink for about 3 seconds.
