688850

Telair Energy 2510g Manual

20
Zoom out
Zoom in
Previous page
1/40
Next page
Energy 2510 G Vers. 001
20
G
B
9 Hour or voltmetric changeover switch button
10 Reset
11 Battery charged indicator
12 Automatic function indicator
13 AUTO/MAN switch for the automatic or
manual function
6.8 MANUAL operation
See section 7.3
6.9 AUTOMATIC operation
Turn the AUTO/MAN switch (Fig.32 Ref.13) to
the AUTO position and set the start-up switch
(Fig. 25 Ref. 1) to ON position.
The automatic function indicator (Fig.32 Ref.12)
will light up. If the battery which supplies the
generating set has a voltage of more than 11.5
Volts, the battery charged indicator (Fig.32 Ref.
11) will light up.
When the voltage at the ends of the 12V DC
terminals of the generating set is lower than 11.5
Volts, the battery charged light indicator (Fig.32
Ref.11) will go off and the generating set will
begin the start-up procedure (similar to that of the
manual operation).
During the operation in automatic mode, the
display (Fig.32 Ref.2) will show the total running
hours of the generating set. Press the hour or
voltmetric changeover switch button (Fig.32
Ref.9) to display the voltage at the ends of the
12V DC terminals, i.e. at the ends of the battery.
When the battery is charged, and anyway after at
least 15 minutes’ running, the battery charged
hours indicator (Fig.32 Ref.11) will light up and
the electronic control panel will turn off the
generating set.
Setting the switch to the
automatic position after turning the control panel
on sets the generating set in stand-by mode and
does NOT activate the automatic function.
Remember that the time which is taken by
the generating set in automatic mode to
recharge the battery may vary according to
the battery status, the amount of connected
batteries and the season temperature.
Generally, the lower the temperature the less
the time required to charge the battery.
Applying any load higher
than the energy just then available in the
battery will prevent the generating set from
turning on due to insufficient voltage.
7 MAINTENANCE INSTRUCTIONS
Only use original spare
parts. Using poorer quality spare parts may
damage your generating set.
Routine checks and adjustments are of the
essence in preserving a high level of
performance. Routine maintenance also
ensures long generating set life.
Before performing any
check or maintenance operation on the
generating set, turn the selector switch (Fig.
31 Ref.2) to the position 1 “manual” in order
to avoid accidentally starting up the
generating set.
7.1 Service check list
See table at the bottom of page 25.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telair Energy 2510g at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telair Energy 2510g in the language / languages: English as an attachment in your email.

The manual is 4,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info