781078
20
Zoom out
Zoom in
Previous page
1/25
Next page
GB
20
2The countdown will stop and the indica-
tor (7) displays 00. A blinking will dis-
play on the indicators for each of the pla-
tes that are powered up.
3At that point, you can time another plate
or alter the remaining time on a pre-
viously time set plate. To distinguish
them, take into account the decimal
point appearing on the bottom right
of the indicator (3), only on that/those
plate/s that are timed at that moment.
In the next 5 seconds, touch one of the
sensors (4) or (5) corresponding
to the plate that you wish to time or alter.
The will stop blinking in the indicator
for this plate and the digits on the indica-
tor (7) of the clock will start to blink.
4Touch the sensors (11) or (12)
again until the required time is set. After
a few seconds the decimal point in the
indicator (7) will start to blink, indicating
that the countdown has started.
If you wish to cancel a timing already set,
simply set the time desired in step 4 to 00 or,
directly, by turning off the plate in question.
When you have timed more than one
plate, by default, the indicator (7) of the
clock will display the shortest remaining
time. This time will correspond to the plate
whose indicator (3) displays the blinking
with the decimal point.
Remember that the decimal point in a
power indicator (3) shows you that this plate
is timed! If this decimal point is blinking and
it’s shown the , it means that the indicator
(7) of the clock is showing you, at that pre-
cise moment, the time remaining in the
countdown for that hotplate.
Please remember that if, during the
countdown, you turn off the touch panel
using the on/off sensor button (1),
the countdown will be cancelled!
Overheating safety feature
The induction areas are protected against
overheating that may cause damage to the
electronic system.
The internal fan is automatically enabled
and disabled, depending on the tempera-
ture of the electronic system. Therefore,
the fan may continue to work for a few
minutes to cool the electronics if you
switch the cooker off when the fan is swit-
ched on.
Power surges
Touch controls can withstand a
certain degree of power surges in the
electricity supply. Abnormally high
power surges can cause the control
system to malfunction (as with any type
of electrical appliance).
Suggestions and
recommendations
To ensure maximum performance from
your hob, follow these guidelines:
*Use pans with a flat base, as the greater
the surface contact between the pan
and the glass, the greater will be the
heat transmission. We recommend the
use of heavy pans so that the base is
more difficult to dent. Figure 4 shows
how pans that are dented or concave
have a smaller contact surface.
fig. 4
Right Wrong Wrong
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Teka IT 612 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Teka IT 612 in the language / languages: English, German, French as an attachment in your email.

The manual is 0.86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info